LAN Party With Ethernet Switch Without Internet?
Oct 10, 2012
I have a school club, but our school does not allow any wireless networks within the school perimeters.Wired are allowed, but wireless are not allowed.I plan to host a LAN party for my club, and we will have about 20-30 people.We cannot have any internet access, and I have not touched a wired stuff, There is a 24 ethernet switch, and if I buy one, and suppose I buy another 24 ethernet switch (I know there is a 48 ethernet switch), can I connect those two 24 ethernet switches to make 47 ports?* For a LAN party without internet access, can we use an ethernet switch or do we use something else?* For 20-30 people, it is recommended that we have a ~8mbps upload speed. When ethernet switches advertise 10mbps, is that upstream & downstream? When all the computers are hooked to 24 ports, does the advertised 10mbps go lower? (I have seen 100/10 mbps, and I don't know what that means)
View 4 Replies
ADVERTISEMENT
May 5, 2012
I'm fairly new to networking but I've learned quite a bit on my own without being educated. I'm trying to just figure things out on my gear. So for my LAN party i'm going to need an internet connection. I'm not going to rely on my venues subnet though so i want to create a new /24 subnet(250 hosts is good for a start). I want my subnet to be able to speak to the outside network too.
View 8 Replies
View Related
Jun 8, 2013
how ISE support on third party LAN switch, if the requirement is doing 802.1X based flexauth.Refer to the diagram i attached; 01 topology.png
Concern 1: if the 3com switch with 802.1X feature, but still without the full feature to support FlexAuth, policy encforcement, DACL etc. In this kind of situation, will user still able to authenticate (using method PEAP-MSCHAP v2), but authorization just grant with permit any any?
Concern 2: Can i assume i authenticated the 3com switch using MAB? But this will cause endpoint with no 802.1X, am i right?
Concern 3: cisco switch C4507-E, loaded with IOS version Cat4500e-UNIVERSALK9-M, version 03.04 and Supervisor Engine :WS-X45-SUP7-E, is this platform is supported in Cisco TrusctSEC?
View 2 Replies
View Related
Mar 23, 2012
Im having a ACT Broadband internet connection, he provides internet connection through a wire which runs into my room that can be directly connected to the my computers NIC. Whenever i switch on my computer and opens the browser it first redirects to the page url... where it asks for Username & Password, our ISP gives us a IP Address which displays on the web page after logging in.I want the internet connection to be shared with my roommates so i bought a 8 port Ethernet switch (url..), which is having a uplink port also. I have connected the wire given by the ISP to the up link port of the switch & i connected my PC to one port of the switch with another network cable. I also connected my friends PC to second port of switch with another network cable, my problem is that when i sign into my ISP web page and start using the internet & my friend also wants internet in his PC & when he opens the browser the ISP's webpage is appearing and when he sign's in internet is disconnecting in my Pc. I tried to change the IP but as a default IP is given by the ISP if change the IP internet is not working.
View 3 Replies
View Related
Aug 9, 2011
I want to connect internet via telephone cable by using rj11 jack from my ethernet switch to another computer it is 150mts away from my office premises.
View 1 Replies
View Related
Aug 12, 2011
can a poe switch be connected to an Ethernet switch
View 1 Replies
View Related
May 24, 2012
I use wireless internet connection and I see “third party setup = Yes under configuration. Is it about sharing data or being monitored
View 1 Replies
View Related
Mar 27, 2013
Any 3rd party CA to provide a root cert for the ACS & verify csr's generated by the 7925's? I've spoken with customer service at Verisign and GeoTrust and either i'm explaining it totally wrong or their not providing CA services for this type of secured environment. sHA1 using EAP-TLS.
View 1 Replies
View Related
Aug 3, 2012
my computer doesn't have a COM port, so i connected an EthernetCOM cable to my laptop (ehternet end) and COM to the switch. Question now is, how can i establish connection?
View 2 Replies
View Related
Jul 29, 2011
I'm trying to connect a few of my devices to the wireless internet at home.
1.Xbox 360
2.Galaxy Tab 10.1
3.My Touch 4g
All of them can recognize the the network they just will not connect. All my freq are good 2.4 or 2.5. WEP Key works no problem, just the minute I try to connect the galaxy tab and cell phone just says "remembered, secured with WPA/WPA2 PSK." The xbox when running the test connection fails as well.
Running vista x64 home premium on HP DV7 1270us.
View 14 Replies
View Related
Jan 13, 2012
I had something odd happen to my Dlink router DIR-651 model. During the early evening hours someone changed the SSID name of my Router. Nothing else changed that I could see right off. So I reset the router to Factory Defaults.
View 1 Replies
View Related
Feb 21, 2013
I would like to use the NCS 1.2 to monitor Juniper SRX 210 firewall. When I try to import the MIB File from NCS, which show "Error: Failed to load MIB File "mib-802" because it is not in the resource path.what I can upload the MIB File from Juniper. [code]
View 0 Replies
View Related
May 2, 2011
I have came across some third-party ws-g5483's that I was thinking of using. But when I go to plug them in, nothing seems to happen. I have tried them in ws-c3548-xl-en and also a ws-c3524-pwr-xl-en with the same results. I know on the newer switches you can do the serviice unsupported-transceiver command but is there anything I can do to get these to work with older switches?
View 5 Replies
View Related
Jul 29, 2012
We have 2 internet providers and I would like to find some way to switch our 5 computers between the 2 internets without having to unplug the ethernet cables everytime someone wants to switch. Is there some type of switch we can buy for each computer to do this or is there no such thing?
View 8 Replies
View Related
Mar 27, 2012
Via ethernet which cable is use between printer to switch
View 1 Replies
View Related
Jan 6, 2012
I have a D-Link Ethernet Switch. I have my computer and a Roku hooked to it. I tried hooking Another Roku and it cannot hook to Network. I unplugged my old Roku and hooked the new one and no problem. Just can't hook both up at once. Is there something I should be doing to enable this? I am allowed 4 computers through my network.
View 7 Replies
View Related
Jan 15, 2011
If I can use my switch as a router or a way to get more Ethernet port? Since my router is down for the count and I need more ports!
View 4 Replies
View Related
Jan 9, 2011
I'm going to be wiring a new (to me) house with a couple cat 6 runs to each room. The runs will all be brought back to an enclosed 6u rack and cat 6 110 style patch panel. This rack will contain:
- HP 2824 Switch
- PfSense router (Supermicro X7SPA-HF ITX board)
- DSL modem
Since the rack is completely metal and enclosed I'm going to put my Netgear WNDR3700 WiFi router (used as an access point only) on top of the rack. My question is, what the implications are in regards to placing a WiFi device right next to a bundle of ethernet cables?
View 4 Replies
View Related
Oct 24, 2011
I am using a cisco asa5520 and i have set up remote access vpn with an AnyConnect connection profile.In the connection profile i have set up that users should authenticate using both certificate and AAA.Due to a high security requirement, the user certificate is issued from a 3rd party. This is working fine and the user now need a valid certificate and a username/password to authenticate successfully.I added the CA certificate as a associated trustpoint on the ASA box to get the certificate verification working.Problem:If Jane and Joe both have a valid certificate AND a valid username/password, Jane could authenticate using a combo of Joes certificate, and Janes username/password. Both are valid (isolated), but i only want jane to be able to authenticate with her username/password and her personal certificate.
View 1 Replies
View Related
May 20, 2012
I'm responsible for designing the network for a LAN party that will be held in October. There will be up to 400 participants and 25-30 crew members. 10 table rows, 40 participants and one 48-port gigabit switch on each table. Core network will be a couple of Cisco 3560G or similar. There will be 2xGbit between the table and core switches.So, how to set up VLANs and subnets for a 400+ people network?
1) Everything on one /23 subnet, or
2) Participants on one /23 subnet, separate subnets for servers, crew and wireless, or
3) Participants on two /24 subnets, separate subnets for servers/crew/wireless, or
4) Separate /26 subnets for each table switch and for servers/crew/wireless?
As far as I can see, the main disadvantage of all participants on one subnet is troubleshooting and isolating network problems - and the main disadvantages of separate subnets is more complex setup and that people cannot browse LAN games other than those on the same switch.
View 19 Replies
View Related
Sep 4, 2011
Does any one used third party SPF in Cisco ASR 1002 series routers, does it supports them.
View 2 Replies
View Related
Apr 23, 2012
I am thinking about running some third-party unified communications apps under VMWare ESXi5 on a Cisco SRE 900 module. According to the Cisco docs, third-party apps are supported on these modules (see table below) but the app in question is NOT on Cisco's list below.
[URL]
Some questions:
1. As long as the third-party app is capable of running under VMWare/VSphere ESXi5, is there anything on the SRE that would prevent you from running this third-party app even though it's not on Cisco's list?
2. What is Cisco's policy on the use of third-party apps that are not on their list? For example, will they take a support call on the SRE running a non-listed app. (I don't want to void any sort of support contract through the use of a third-party app not on their list).
View 2 Replies
View Related
Jun 17, 2012
My main PC and modem is in a back room of the house, my secondary PC and game systems are in the living room.My main PC HAS to have a wired internet connection because that is what I want.My game systems and second PC need a wired connection.I would like to have my D-Link wireless router in the living room so I can use the WiFi for my iPods, iPad, laptop, and anything else that I am looking at when I am sitting on the front porch. I have an Epson printer that I can hook up to my network that I want to be in the back room with my main PC.To get the internet into the living room I am going to run a CAT5E ethernet cable under my house (off the ground and away from electric wires and copper pipe) from my back room to the living room.Is it possible for me to go from the modem to a switch box (I actually have two switch boxes, but I believe I will only need one)which would be connected to my main PC, the printer, and the ethernet wire going under the house to the living room... Then in the living room have the wire that comes from under the house (from the back room) go directly into the wireless router and then from the router have cables going to my game systems and the second PC?If this will work, will I still be able to control the wireless router with my main PC?
View 9 Replies
View Related
Jan 13, 2012
I connected a switch and the device is not even recognized in my router site.
View 12 Replies
View Related
Feb 21, 2013
I bought a "Nexxt Solutions 8 ports Ethernet Switch" and it only allows me to use the internet on the first computer that I plug into one of the Lan ports. I get a Limited Connection MessageI did some research and found something about a DHCP Server and automatic IP assignment, but I can't find a comprehensive tutorial on how to setup this.I'm sure the solution is simple.
View 2 Replies
View Related
Jan 7, 2011
So my old router needed replacement and my dad bought a Netgear gigabit ethernet switch instead of a router. It said that it gets 1Gbps when I look inside the local area connection speed. The problem was we tried to use it like a router but only 2 computers could connect to the internet at one time but it was indeed noticeably faster when it came to video streaming speed. We since returned it and bought a Netgear N600 router that says the speed is 300mbps but like my old router it shows the speed is actually 100mbps and the streaming is good for the most part but every now and then slows down. Would using the ethernet switch with our new router work with streaming speeds and connection stability and of course let more computers connect and also use the routers wireless.
View 13 Replies
View Related
Oct 2, 2012
OK i'm re-organising my network setup, most of my devices in my room are hard wired through Ethernet but some devices in the house need to run wireless.Currently i am running a super hub that has been configured into just modem only and a wireless router that gives wireless and hard wires up to 4 devices. Im wanting something that can be mounted out the way like an Ethernet switch but give it wireless accessibility too. I see you can buy access points to connect to your Ethernet switch device but will it give ample wireless connectivity if im running 4+ hardwired devices?I have recently been upgraded from 30Mbps to 60Mbps, this is fed from cable connection to the modem.
View 5 Replies
View Related
Aug 8, 2012
I have a Ethernet module (SM-ES3G-16-P) installed in a 3945 router and noticed during first boot no licenses are active at all. I would assume at a mimimum ipbase would be active. With this module, does static routing work with just ipbase?
Example:
interface g0/1
no switchport
ip addr 192.168.254.2 255.255.255.0
[code]....
View 3 Replies
View Related
Dec 10, 2012
I have a couple of 2600 APs (external antenna) which are getting PoE from my switch but no ethernet. This is happening on both APs. If I connect a laptop to the (cat5e) cable I get ethernet. If i move the AP to another patch lead adjacent to my switch I get ethernet connectivity too. So, change the cable is the answer I thought, however I have exactly the same issue on both APs and each ethernet cable has been reterminated a number of times (straight through). I wonder is the 2600 AP less tolerant to the actual ethernet cable ?
I just swap the cable, however the patch leads have been run (only 15m or so) and have been replaced once - relaying again is not an easy job. It's more a case of reterminating the cable that is already there and as I've already done this a few times on each patch lead and the results are the same each time I'm thinking I'm missing something obvious.
View 10 Replies
View Related
Feb 25, 2013
I contact you due that I’m currently configuring a Router Cisco 2921 with an Etherswitch module. The specific inventory of Router Cisco 2921 is:
Router#show inventory,NAME: "CISCO2921/K9 chassis", DESCR: "CISCO2921/K9 chassis"
PID: CISCO2921/K9 , VID: V06 , SN: XXXXXXXXXXX
NAME: "High Speed WAN Interface Card - 1 Port Gigabit Ethernet on Slot 0 SubSlot 0", DESCR: "High Speed WAN Interface Card - 1 Port Gigabit Ethernet"
PID: HWIC-1GE-SFP , VID: V01 , SN: XXXXXXXXXXX"
[Code]....
View 1 Replies
View Related
Oct 24, 2011
I am new to these forums and I have upgraded from firmware 1.00 on the DIR-815 to the 1.01 firmware and once I upgraded, I can log into Xbox, but can't host party chats or host game rooms. I also noticed that any and all messages sent from friends didnt show until I rebooted my console. Something is SERIOUSLY WRONG here and would like a MOD to comment on this.
View 12 Replies
View Related
Jun 22, 2011
Xbox works fine for some things, I can access Netflix, can download from live marketplace, etc, but cannot join a party and cannot play a game. Other people cannot join my party, cannot play my game. Error when I try to join a party is "Can't connect to xbox live party, there might be a network problem."
Xbox join party and games work fine when connected directly to comcast (motorola) modem.Dir-601, firware 1.02NA and 101NA. Hardware version A1.Port forwarding TCP 53,80,3074 and UDP 53,88,3074 - also included TCP 80 and 21 to no avail.
View 1 Replies
View Related
Sep 29, 2009
I am attempting to install a third party SSL cert (GoDaddy) to properly secure the external interface of my 1811 ISR so that I can implement SSL VPN. I have tried using SDM 2.5, but that doesn't appear to be working. I am familiar with doing this on a Cisco 3005 Concentrator, but I'm not aware of how to install an intermediate cert on the 1811 (or if it's even possible), in order to properly have the GoDaddy cert properly imported and used for SSL VPN. I have gone through the CSR process and have the initial cert from them generated and have imported it, but it never appears to be identified correctly if I browse to the external interface on the router. The router always defaults to its self-signed cert.
View 1 Replies
View Related
