Adding Wireless To Ethernet Switch Setup?
Oct 2, 2012
OK i'm re-organising my network setup, most of my devices in my room are hard wired through Ethernet but some devices in the house need to run wireless.Currently i am running a super hub that has been configured into just modem only and a wireless router that gives wireless and hard wires up to 4 devices. Im wanting something that can be mounted out the way like an Ethernet switch but give it wireless accessibility too. I see you can buy access points to connect to your Ethernet switch device but will it give ample wireless connectivity if im running 4+ hardwired devices?I have recently been upgraded from 30Mbps to 60Mbps, this is fed from cable connection to the modem.
View 5 Replies
ADVERTISEMENT
Sep 9, 2012
my sister gave me an old ethernet switch so I could use the internet on my computer and my PS3. Unfortunately I didn't get any type of setup manual so I downloaded one off the manufacturer's website
View 1 Replies
View Related
Jun 15, 2012
My dorms have wifi in the common room, and ethernet wall ports in the rooms since wifi doesnt reach that far. They both have the same network name (e.g. the wifi network is named 'apple', and when i connect through ethernet in my room the name is also 'apple') I need to have wifi in my room. So, if i get a router and connect it to the ethernet port in my room's wall, would that work? Is that all you have to do or is there some other stuff i should know about?also can i put a password on it? And also, will it carry the network traffic of the common room?(if two people are using the common room's wifi, will the wifi speed in my room be affected nd whatnot) i have a linksys router lying around at home (the blue one with the double antennas, everyones seen them, and the one in the common room is the same...wireless g)
View 7 Replies
View Related
Jan 7, 2012
I am staying with some family for the next two months and they don't have wireless internet at their house. When they bought their house it was wired for ethernet and have the modem going to a netgear 8 port switch which is going to the different rooms of the house. I would like to add a wireless access point to one of those 8 ports coming from the switch. I currently have a TP-LINK TLWR740N router that I can configure into an access point, or I can buy just and access point. Unfortunately it is not an option for me to plug the modem into the router and then the router into the switch.
View 1 Replies
View Related
Jan 26, 2012
I would like to set up a WAP at home so that we can choose when different members of the family have wifi access.I am currently using ethernet and a Thomson Speedtouch 546(i) V6 router. We have 3 laptop PCs and an imac, also a PS3 and Wii
View 4 Replies
View Related
Feb 26, 2013
I have a working 3800 router which runs on bgp pretty well. Existing setup has 2 serial ports for the bgp and 1 gigabit port for the LAN.Now, i want to add another 3800 as a standby router making it clustered - ACTIVE/STANDBY via hsrp protocol.
1.) What are the implications in adding another 3800. Do i need to reconfigure the ip addresses on my serial? or just the LAN
2.) Are there any additional requirements like firmware versions etc?
View 1 Replies
View Related
Aug 19, 2012
I have 1 computer, desktop, and would like to hook up a wireless to use for phone and kindle,etc. Question is shoud I use a switch or router? I have a netgear fs105 and hooked it up but was told it's not wireless (that's how much I know). Have Vista. and dsl.
View 2 Replies
View Related
Jan 30, 2013
We have upgraded our switch and since then Remote web workplace and owa are not working
View 1 Replies
View Related
May 14, 2012
I've added a number of switches to NCS and some of the switches had the wrong snmp communities, etc so weren't added as switches but instead were put under unknown devices.
I've corrected the information for each unknown device and am now seeing the following inventory status:1951799867 (IP: 10.243.26.22) will not have its features collected due to , device SPT_ONLY
They're still unknown devices and there seems to be no way to get them to show up as switches.I've tried to remove these devices but without success (despite a message appearing below the devices I tried to remove saying "Selected device(s) removed successfully.")
View 1 Replies
View Related
Feb 24, 2011
I'm trying to set up a wired ethernet connection to a wireless Belkin router. The wireless router works fine - I have several devices that will connect wireless with no problem. The hp desktop I'm trying with the wired connection is showing that the ethernet connection is working, but it's not asking for the wireless network name or security code, and the internet will not work?I made sure the desktop was set up to automatically obtain IP addresses, then I did the "ipconfig /flushdns / ipconfig /release and ipconfig /renew commands, but it still won't work.
View 5 Replies
View Related
Sep 18, 2012
I recently purchased a Mac and wanted to reset my wireless router and set it up using my mac. However, when I downoaded the software to set it up again, it said it was not compatable with my Mac OS (X Lion 10.7.4). I am sure there is a way to manually set it up via an ethernet connection, but I am at a loss as to how to do that. The wireless router is working just fine, I am able to connect to the internet wirelessly and there's nothing wrong with my internet service, however the wireless router is not secured.I have my Mac connected to the wireles router via an ethernet cord.
View 1 Replies
View Related
Apr 16, 2012
I have 6 cisco switches already on my network and I just got a 2960S PoE switch that I need to enable for VoIP. The voice vendor is coming in to setup our phone system for VoIP and I need to enable this new 2960S 48 port switch for the VoIP phones, I don't know how to do that, or other taskes needed for this project.
I was told that I need to uplink the new 2960S with the Catalysy 4507R using an ethernet cable and to "trunk the ports" and enable the 2960S as a VTP client - ok great - how?
I was told I also need to use the switch port voice VLAN command for the new VLAN - again, great - but how?
I actually was able to telnet into the switch and I gave it an IP and I created a new vlan but thats all. We are using non Cisco IP phones.
View 4 Replies
View Related
Mar 23, 2012
I have a Catalyst 3750 I want to add to an existing stack (same models) through the stackwise port We use some complex QoS and other features on our network, and I'm not sure how much configuration I need to do on the new switch before adding it to the stack. Since this is going into an existing setup?
View 9 Replies
View Related
Jun 17, 2012
My main PC and modem is in a back room of the house, my secondary PC and game systems are in the living room.My main PC HAS to have a wired internet connection because that is what I want.My game systems and second PC need a wired connection.I would like to have my D-Link wireless router in the living room so I can use the WiFi for my iPods, iPad, laptop, and anything else that I am looking at when I am sitting on the front porch. I have an Epson printer that I can hook up to my network that I want to be in the back room with my main PC.To get the internet into the living room I am going to run a CAT5E ethernet cable under my house (off the ground and away from electric wires and copper pipe) from my back room to the living room.Is it possible for me to go from the modem to a switch box (I actually have two switch boxes, but I believe I will only need one)which would be connected to my main PC, the printer, and the ethernet wire going under the house to the living room... Then in the living room have the wire that comes from under the house (from the back room) go directly into the wireless router and then from the router have cables going to my game systems and the second PC?If this will work, will I still be able to control the wireless router with my main PC?
View 9 Replies
View Related
Dec 10, 2012
I have a couple of 2600 APs (external antenna) which are getting PoE from my switch but no ethernet. This is happening on both APs. If I connect a laptop to the (cat5e) cable I get ethernet. If i move the AP to another patch lead adjacent to my switch I get ethernet connectivity too. So, change the cable is the answer I thought, however I have exactly the same issue on both APs and each ethernet cable has been reterminated a number of times (straight through). I wonder is the 2600 AP less tolerant to the actual ethernet cable ?
I just swap the cable, however the patch leads have been run (only 15m or so) and have been replaced once - relaying again is not an easy job. It's more a case of reterminating the cable that is already there and as I've already done this a few times on each patch lead and the results are the same each time I'm thinking I'm missing something obvious.
View 10 Replies
View Related
Sep 12, 2012
We have a WS-C3750G-24PS switch running 12.2(50)SE , C3750-IPBASEK9-M in production & stand alone and we want to ask a new Cisco WS-C3750-24P running 12.2(55)SE3 , C3750-IPBASEK9-M into the stack with the 1st one.
Just want to know if it is possible and are there any problems with the IOS being different version.
View 8 Replies
View Related
Mar 10, 2008
After I added the 3rd 3750E to my stack on Sunday I can no longer save my configs with 'copy run start' or 'write mem':
#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
nv_done: unable to open "flash:/config.text.new"
nv_done: unable to open "flash:/private-config.text.new"
nv_done: unable to open "flash:/multiple-fs.new"[OK]
[code]....
my flash seems to have plenty of space:
57409536 bytes total (24203776 bytes free)
View 4 Replies
View Related
Mar 3, 2013
I've a WLC 2106 and it is running IOS version 7.0.240. I am trying to setup a wireless mesh and used the Ethernet bridge port on the MAP to extend the network. The wireless mesh works fine but I can not get the switch to work that is connected to the ethernet port on the MAP.I'm using two different Access points. I'm using a Air Cap 3502i as the RAP and a Air Lap1142N as the MAP.The switch port that is connected to the RAP and MAP is configured as the following:
switchport mode trunk
switchport trunk native vlan 2
switchport trunk allowed vlan 10,20,30,40
[code]....
The wireless mesh between the RAP and MAP works fine. I can connect a device to the MAP wirelessly and access the network with no problem but I can not get anything to work that connects to the switch that is connected to the MAP ethernet port.
View 2 Replies
View Related
Apr 22, 2011
on my home network I currently only run an Airlink101 AR675W router. We have a couple issues with this. The router for one is in my basement and there are points in my house that have low signal strength, especially upstairs in the far corners of the home. Second is I am currently running my home PC as a media center but it is set-up wirlessly so streaming is clunky and jittery. Also on this network is 3 X-box's wired, a PS3 running wirless, 2 PC's wired in, 2 wirless laptops and the afore mentioned wirless PC. A lot of weight for the network. What I want to do is move the router upstairs, hardwire it into my wireless PC (the one doing the streaming) and connect a second router (an identical make and model I am buying this weekend) downstairs which will be basically used as an "expansion" of the wirless and a switch for the hardwired devices downstairs. would this be better than simply moving the wirless router upstairs (hardwiring my PC) and putting a 5 or 8 port switch in downstairs for the X-box's and 2 wired PC's there?
View 2 Replies
View Related
Mar 25, 2012
in our network we were using three 3750-48-s switches with stacking one of the switch due to some hardware failure power problem,
now i want to add a new switch 3750-48-s in the existing Stack two switches , the old two switches ios version is = 12.2(25r)SEC the new Catalyst 3750 io verion is = 12.2(35)SE5
how to add this switch in the existing two stack switches , with documentation
View 1 Replies
View Related
Nov 23, 2011
I am looking to add a new 3750 Switcch to an existing stack shown below
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 26 WS-C3750-24P 12.2(35)SE5 C3750-IPBASE-M
2 26 WS-C3750-24P 12.2(35)SE5 C3750-IPBASE-M
3 26 WS-C3750-24P 12.2(35)SE5 C3750-IPBASE-M
[code]....
I have looked on notes to add a switch to an existing stack and haven’t identified answers on how the IOS will be affected on the new switch – will it downgrade to the current stack version or will the current stack upgrade to its version. At this moment in time I would prefer if the new switch IOS downgraded to the current stack IOS version.The new switch is a 3750V2 – will this affect how it joins the stack?The new switch has the image of IPBASEK9-M – again will this affect how it joins the stack?
View 5 Replies
View Related
Jul 31, 2012
Trying to find some documentation as to whether there are any other steps for inserting this new module in our N7K. We have 2 blades in already and 2 Sups in 5 & 6. I'm assuming its like the 6500s, where we just slide it in and the OS configures the global parms for it and the default VLAN.
View 2 Replies
View Related
Dec 6, 2012
I am having an issue with adding a c3750x switch to an existing switch stack Currently there is 2 x WS-C3750X-48P and I am trying to add another WS-C3750X-48P to this switch I have cabled the switch to the stack using the stack cables and added the command to provision the switch on the exisitng stack. However when I turn the switch on it just goes on its own stack.
I noticed the new switch had a later version of IOS so have downgraded this to the same version as the other switches but still no joy Here is the sh ver from the exisitng stack
uptime is 4 weeks, 4 days, 23 hours, 30 minutes
System image file is "flash:/c3750e-universalk9-mz.122-53.SE2/c3750e-universalk9-mz.122-53.SE2.bin"
License Level: ipbaseLicense Type: PermanentNext reload license Level: ipbase
cisco WS-C3750X-48P (PowerPC405) processor (revision A0) with 262144K bytes of memory.Processor board ID FDO1448Z0FJLast reset from power-on21 Virtual Ethernet interfaces1 FastEthernet interface156 Gigabit Ethernet interfaces6 Ten Gigabit Ethernet interfacesThe password-recovery mechanism is enabled.
[code]....
View 3 Replies
View Related
Oct 16, 2012
I am attempting to add and Catalyst 3750 - 12 port Gigabit switch to an existing stack of 3750 48 port switches (non-X fabric). I am not sure how to proceed. These are the two questions/thoughts I have. Any additional perspective I should have before proceeding.
What kind of configuration should I apply to the Gig switch before adding it to the stack?I am sure I will need to assign priority to the new switch, ideally, it will act as master.
View 1 Replies
View Related
Jan 23, 2013
We have a cisco stack with 5 ws-c3750-24p 12.2)55)SE3 c3750-ipbasek9-m switches. Can i add a switch to the stack that is the following model: ws-c3750g-48ts 12.2(25)see3 c3750-ipbase-m
View 3 Replies
View Related
May 11, 2012
I have a Cisco WLC 2106 and I got 2 access points working, conected the controller (Aironet 1130AG), but I would like to know if I could connect a host or a laptop to the 2106 WLC.
I have a router conected to the WLC using the port 1, and the APs are in ports 7 and 8, but when I plug a pc in the port number 3, I do not get and IP from DHCP server, (DHCP is giving by the router). Im not sure if the 2106 WLC ports are for connect other network devices like a pc... I would like to know if there is a way to configure the controller to conect a host or a pc to the ethernet ports.
View 5 Replies
View Related
Feb 6, 2013
I have a situation where my Cisco 5508 did not come with SFP by default.
Can i use the SERVICE PORT to connect the WLC to the Switch
1. the controller has 8-SFP Slots
2. one service Port
3. On redundant Port
View 11 Replies
View Related
Sep 7, 2012
We have two catalyst 6506 switches with 10 gb u plinks and around 120 edge switches cat 3750-x switches. Still the module on the core wheere servers are connected is 1000mbps port.Now if we induct a nexus switch to the datacenter what kinds of benefits we can reap In a virtulised environment as well as real environment?following are the some of the queries.Can we reduce the number of edge switches? ( by virtual environment), Inter operabaility between cat ios and nexus ios, how this will affect the environement,What will be the over all benefits ?, What are the cons of this induction ?
View 22 Replies
View Related
Feb 29, 2012
I currently have Cisco 3750G which is currently live and active and fully populated and only have remote access.
I have an additional same switch which I would like to stack. My initial plans were to have 2 GIbit etherchannels, but I came across the option to Stacks both switch with each other.
When I do a show switch on the live switch its set as a Member: [code]
I would like to add the new switch to the stack without losing the config for the switch which is live. I understand that the highest priority of the switches becomes the Master but as the live switch is Priority 1, would chancing this affect the switches config, or would it lose connection at all?
Also when I plug in the new switch and it reboot how do I ensure it becomes the slave without rebooting the live switch?The cables on the switch do they have to go to port1 on the live switch and port 1 on the new switch or can they be port 1 and port 2?
View 19 Replies
View Related
Jan 10, 2012
ws-c2960-24tt-L Ethernet switch adding or removing any device from switch cause a loss of connection to all other devices on switch for about 60sec.
View 1 Replies
View Related
Dec 29, 2011
In my main office, I have a cable modem which is connected to my main E4200 router. All of my equipment (except my Ooma) is served by the E4200. The E4200 broadcasts a wireless network.In my basement, I have a Wii / entertainment center. The E4200 signal from upstairs isn't strong enough to stream video.
I bought the WET610N and have successfully set it up to interact with the E4200 wirelss network. I can hardwire my laptop to the WET610N and verify the internet works greatHowever, the Wii must connect over wireless. I have other equipment in the basement which would benefit from an internet connection. So, I want to A) connect the ESXS88W 10/100 8-port workgroup switch I have to the WET610N *AND* also broadcast a wireless signal in my basement (assuming the wireless network I see in the basement is the same "old" one from upstairs which has not benefited from the WET610N).
How can I set up my WRT54G2 to broadcast a wireless signal in the basement so that it leverages the E4200 signal served by the WET610N, while also having the workgroup switch offer hardwired connections to my other equipment (like Dish Network receiver)? It doesn't seem to work by just plugging the WRT54G2 into the workgroup switch.
View 2 Replies
View Related
Aug 12, 2011
can a poe switch be connected to an Ethernet switch
View 1 Replies
View Related
Sep 18, 2012
I want to use a linksys router with a 3com switch. 3Com model 3CGSU08A.i have two routers to choose from a E2000 and a WRT54GL which one is better and settings to use.
View 1 Replies
View Related
