Cisco Wireless :: Does Ethernet Ports On WLC 2106 Works As A Switch
May 11, 2012
I have a Cisco WLC 2106 and I got 2 access points working, conected the controller (Aironet 1130AG), but I would like to know if I could connect a host or a laptop to the 2106 WLC.
I have a router conected to the WLC using the port 1, and the APs are in ports 7 and 8, but when I plug a pc in the port number 3, I do not get and IP from DHCP server, (DHCP is giving by the router). Im not sure if the 2106 WLC ports are for connect other network devices like a pc... I would like to know if there is a way to configure the controller to conect a host or a pc to the ethernet ports.
View 5 Replies
ADVERTISEMENT
Feb 21, 2013
I bought a "Nexxt Solutions 8 ports Ethernet Switch" and it only allows me to use the internet on the first computer that I plug into one of the Lan ports. I get a Limited Connection MessageI did some research and found something about a DHCP Server and automatic IP assignment, but I can't find a comprehensive tutorial on how to setup this.I'm sure the solution is simple.
View 2 Replies
View Related
Jan 16, 2012
this router of my girlfriends only works when iplug the dsl modem into the output ports what could possibly cause this. would a firmware upgrade straighten it out...
View 1 Replies
View Related
Oct 15, 2008
basic question regarding the switchports on the rear of the 2106 controller. How do I configure them for use? I'm using port 1 as my uplink to a trunk port on an ASA and my network traffic to the management interface and guest vlans is all working as expected, but when I plug anything into any of the other ports, they get no addresses from my dhcp server (the ASA). I see nowhere to configure which vlan to tie the ports to or anything. I suppose I'm more used to a catalyst or ASA where I can just pick the ports and vlans (or trunks) I want to attach them to. [code] Again, all of the existing network functionality (private and guest network) is all functioning fine so I'm pretty confident I have the above configured correctly, I just cant make any progress on the WLC ports 2 - 8.
View 13 Replies
View Related
Mar 3, 2013
I've a WLC 2106 and it is running IOS version 7.0.240. I am trying to setup a wireless mesh and used the Ethernet bridge port on the MAP to extend the network. The wireless mesh works fine but I can not get the switch to work that is connected to the ethernet port on the MAP.I'm using two different Access points. I'm using a Air Cap 3502i as the RAP and a Air Lap1142N as the MAP.The switch port that is connected to the RAP and MAP is configured as the following:
switchport mode trunk
switchport trunk native vlan 2
switchport trunk allowed vlan 10,20,30,40
[code]....
The wireless mesh between the RAP and MAP works fine. I can connect a device to the MAP wirelessly and access the network with no problem but I can not get anything to work that connects to the switch that is connected to the MAP ethernet port.
View 2 Replies
View Related
Oct 8, 2012
I have 4 cisco 2960 switches to which many users are connected. No vlans are the only default vlan 1 is there. Now I want to make ether channel on switch 1 whcih has 24 fast etherenet ports. Can I make port 1- 8 as one ether channel which are connected to users or i can only make ethere channel of ports that are connectd to other switchs. If I can, how the other switchs will comnicate with the switch ports bundalled in the ether channel in switch 1.
View 6 Replies
View Related
Jan 23, 2011
I have a Netcomm NB9WMAXXn router and 3 laptops i want to connect to it wirelesslyThe problem is that the iwreless internet connection slows down and eventually drops out after about 30m unless one of the laptops remains connected via Ethernet to the router. The wireless laptops will remain connected to the router but the internet connection will fail. The laptop with Ethernet connection retains a very good connection so i'm thinking this is an issue with my router or it's configuration
View 1 Replies
View Related
Jun 30, 2012
While im playing games like battefield 3 left 4 dead 2 or minecraft i get rubberbanding lag which is basically my game character running foward then being shot back to his original postion. I originally was using a wireless usb adapter so i blamed it for the cause of the lag. (My pings were fine btw) I went to ethernet for a week and the lag went away so everything is fine via ethernet. I just bought a new wireless card but there is still this terrible lag!
View 10 Replies
View Related
Jun 9, 2013
We have an ASA 5505. 5505 comes with two default vlans 1&2 with each of them marked as inside & outside respectively.My query is , if i do not want to use vlans on 5505 and only want to use the Ethernet ports as pure physical layer 3 ports, is it possible?i.e. i want to assign a layer 3 ip address on eth0/0 and eth0/1 and make them as the inside & outside interfaces rather than vlans. is it possible to do away with vlans in 5505 & will it work otherwise?
View 3 Replies
View Related
Jun 9, 2012
Our home school's having trouble attaching a wireless router to my XP PC's ethernet port.Our donated vintage Macs and XP machines are tied to the internet via a cable box's wireless router. Works just fine. Now I wish to boost the signal to a building beyond the local area by attaching a wireless router to a Dell 260 running XP. This router's IP is 192.168.11.1 (ON) and 192.168.11.100 (OFF), and I've spent hours with the Connection Wizard thing on XP trying to create a ethernet path to the router but I can't find a configuration that states an ethernet path or channel. The modem lights normally and other machines can pick up and connect with its signal but there's no real transmission, the receiver machines getting:Firefox can't find the server at [URL].Check the address for typing errors such as [URL]instead of [URL] If you are unable to load any pages, check your computer's network connection.If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the Web.Ironically, the router works just great on the Macs, which has both Airport on to receive signals from a cable TV wireless router and also has its shared Ethernet connection on, and the ethernet side requires no IP configuration like it seems you must on the XP's internet connection page. The router in question just plugs in the Mac and transmits just fine. I would use the Mac for this purpose but I really wish to use the Dell.The Dell's current network configuration after many trials:
Wireless Connection 3
LAN / High Speed Internet
Connected, Firewalled
802.11n USB Wireless LAN Card
IP 169.18.2.7
[code]....
Oddly, the Mac's Network panel states: "The cable for built-in ethernet is connected, but your computer does not have an IP address and cannot connect the internet." Yet it does!
View 6 Replies
View Related
Dec 30, 2012
Mac airport shows full bars in network connnection and green connected dot, but no access to internet. Ethernet connection works fine. I also couldnt connect with my Iphone.
I have Charter cable with Motorolla SB6121 modem. I've reset the modem, rebooted everything, cloned my ip address, all several times .......but still no go.
Linksys says they don't support this router anymore accept for a pay for support service, which I would like to avoid.
View 5 Replies
View Related
Mar 13, 2013
I try connecting via ethernet cable and it doesn't seem to work until the administrator of the network (my brother) comes home and then turns his computer on and starts using it. However, if i switch to a wireless adapter it sometimes works (like right now) even when my brother is not using the internet. Also, i tried to connect via wifi on my macbook pro to the same server and it used to work flawlessly 100% of the time, now i can only connect once in a while for short periods of times.
View 1 Replies
View Related
Oct 5, 2011
lost wireless to all wireless devices (laptop, iPhone and iPad). Still have hard wired ethernet internet access from desktop. Tried resetting router, powering off router, resetting and powering off cable modem. Nothing works. Lights on router all on.
View 1 Replies
View Related
May 1, 2013
I have a E4200 v1, connected with a few PCs by ethernet ports and various devices by wifi. Now the wireless devices work perfectly but sometimes the PC via ethernet ports cannot connect to LAN and internet.
View 2 Replies
View Related
Aug 7, 2011
How many of the 881 switch interface ports can be used as router ports, have used the 877 etc where i can use 2 but need a low cost router that supports 3 for routing. (needs to be physical ports)
View 2 Replies
View Related
May 9, 2012
If I hook up a wireless router as an access point will both the Ethernet ports and the wireless connection on that router work?
View 2 Replies
View Related
May 17, 2012
My computer worked fine on the eithernet, but I had to move it to a different room and now it won't recognize ANY WIFI connections. I know the wifi is working because I have laptops and phones connected to it. the computer is only 8 months old. It's an HP Pavillion AMD Phenom II 820 Quad-Core Processor, Windows 7 64 Bit, Wireless LAN 802.11b/g/n.
View 19 Replies
View Related
Apr 7, 2012
I can't seem to connect to the internet via the Ethernet port on my laptop, but the built-in Wi-Fi card works perfectly fine. I normally use Wi-Fi, as our signal is very strong, even if I go outside and up the road, I can still connect.
My issue is that although I don't need it, I'd like to setup Ethernet for the first time since installing Windows 7. I've had Windows 7 since April 2011, and prior to that I used Windows Vista. From memory, I don't think Vista had any problems with connecting via Ethernet back before I moved house, but this was over two years ago.
My laptop is an ASUS X58L, and the NIC identified by Device Manager, is a Realtek RTL8139/810x Family Fast Ethernet NIC. Going into the properties, I can see that I have the latest Windows 7 driver installed - 6.111.723.2009, however prior to this I had the driver that came with the machine (when it was running Vista), which was 6.108.331.2008 and tried updating from Device Manager, but for some reason it said that I had the best driver already installed. To install the 2009 Windows 7 driver, I had to manually download it from Realtek. With either of the drivers, connecting via Ethernet doesn't work, and I'm confused as to what to do next.
View 13 Replies
View Related
Nov 15, 2011
I'm visiting my friend at her apartment and her internet only works through an ethernet cable. I unplugged the cable from her computer and plugged it into mine and it worked perfectly but when we switched it back to her computer her internet takes forever to identify and ends with local only connection how do we fix her computer?
View 1 Replies
View Related
Nov 3, 2012
I recently finished my basement and put together a home entertainment system. I ran ethernet through the walls to a wall jack. I plugged my laptop into it and it tested good (internet worked and pinged my router 1ms time & 64 TTL.) I put an A/V rack in front of it and brought down my Netgear GS605 switch, XBox360, BD player that had all been on the network upstairs and added a new LAN capable receiver. None of those components will recognize the network. Light doesn't light on the switch(neither amber nor green,) Xbox doesn't recognize a cable is even plugged in. I unplug the switch and using the same cables my laptop picks it up just fine. I bypassed the switch and went strait to the other A/V gear and none of them recognize the network.By the way, the switch is auto detect between patch/crosssover. The IP settings are all the same from when the gear was connected upstairs.
View 6 Replies
View Related
Aug 9, 2012
I've been having an issue with my internet connection. I have AT&T Uverse high speed internet, complete with the Motorola NVG510 ADSL modem. For the past couple weeks, my download speeds have gone from 1.0 MB/s to < 100 KB/s up to 400 KB/s if I'm lucky.I used to be able to download files and watch videos at the same time with very little trouble, but now I only have enough bandwidth to either do one or the other without causing any problems. I thought my ISP had throttled my bandwidth, but I've run the Glasnost tests at url... and it came back as fine.It may not mean anything, but I should note that a few weeks ago, we had storms move through the area and lightning struck our house. It ended up shocking my mom through the USB mouse while she was using my computer, it blew out one of my computer speakers, and I believe it's the reason why the ethernet port on my motherboard no longer works.
View 13 Replies
View Related
Dec 19, 2012
Earlier my desktop was to b in d same place where the router was der. Everything worked fine. Now I decided to shift my desktop to another room. I have kept the router at the earlier place only. I have brought a 25m long new cat 5 cable. When I connected it to my desktop, the orange led on ethernet port do not light up and the desktop is unable to detect the ethernet cable and hence the internet connection. On the router, a light of ethernet keeps on blinking every 1 second. I was worried whether my ethernet port got fried. So i inserted another ethernet cable, but then the ethernet orange light came and the pc detedted the connection. Therefore I thought the cable might be faulty. Therefore I connected my laptop with that 25m cable. But my laptop detected it and showed the internet connection. But now when i again connect the cable to my desktop, there's no light and the pc does not detect it. However, if i connect the 25m cable to my desktop then during boot the ethernet light on router is stable just as when it is normally connected to the internet. But when i go into windows it starts blinking every 1 second.
My router is MTNL Model No. UT-304R2
Desktop - Asus P7H55, core i5
Laptop- HP 2000
Windows 7 Ultimate on both desktop and laptop.
View 17 Replies
View Related
Feb 28, 2012
I have my internet coming from my DSL modem (of course) and running into my wireless router. Once it is in the router I can't get a connection, period. Not even through any of my router's ethernet ports. This wasn't the case until about 3 o'clock yesterday. If I unplug the cable from my wireless router and plug it directly into my computer it runs fine. If I run it through my Micro-Cell tower and into my computer it runs fine. But if I plug it into a router it won't work through Wi-Fi or Ethernet. I have tested the connections of all the ethernet cables I am using. Figuring it had to be a problem with my router (since it was working earlier and the connection only disappears when plugged into it) so I bought another, same problem. What else could it be? PS: I'm using both a MacBook Bro, a PC, a PS3, and a Nintendo 3DS and none get a signal from the wifi. I always keep the PC hardwired through the ethernet ports on the router and use the wireless for everything else
View 1 Replies
View Related
Oct 28, 2011
I've been using the Linksys router e1000 N type for a week now and it hasn't beeen such a great experience. The thing is when i connect the modem to my laptop via ethernet cable internet works but not when i connect the cable to the router even though this worked before. actually a few hours before. so i dont know whats happened to my router since clearly the problem is in there. the modem has lights for PC Cable DATA and POWER. The lights to all of them blink when i have connected the modem directly to laptop but the PC light is non existent when i connect it to router. hence i get no internet access. the routers power is on so i dont know what the prob is ive rebooted it a few times but to no avail.
View 1 Replies
View Related
Feb 18, 2013
I have a 80ft cat5 ethernet cable I got cut at compusa about 3years ago to go across the house to my room. I used to have an a really old computer but about 6months ago I bought a brand new top of the line computer and got really excited and set it up on my desk in my room to discover my ethernet cable wasnt being detected on my computer. The weird part is that it works with other computers.. I had my gf's laptop(3yo) using it, my dads(3yo), my older computer that I dont use anymore but whenever I connect mines it doesnt work.I test hooking up a few different cables to my computer and they work but that one specificly wont.
View 3 Replies
View Related
Mar 21, 2013
I just updated my F5D8233-4 ver 3000 router with the latest firmware. Now only one of the hardwired ports works (#1) and it causes the router trouble enough sometimes to make it disconnect from the cable modem. All the wifi connections (5 of them) work well and do not appear to cause any trouble. What can I do?
View 1 Replies
View Related
May 29, 2012
Region : Ireland
Model : TL-MR3420
Hardware Version : V2
Firmware Version :
ISP :
I have my router updated with the latest firmware and I'm pretty sure all the settings are correct but I'm only getting a max transfer rate of 144Mbps. I know this because I use InSSIDer 3 to analyse my wifi network etc. I stream movies over my network and while DVD quality movies play fine, HD movies tend to freeze and buffer a lot. I have the router's channel width set to 40Mhz, so I know that's not the problem. Strangely, I also use a Netgear wifi extender with the MR3420 and it's max rate is 300Mbps.
View 7 Replies
View Related
Oct 27, 2011
I've lost connectivity with all but one of the ethernet ports on my E4200 router. My desktop PC was connected to Port 1 but stopped working. Network troubleshooting via my Windows 7 Dell 8300 said I was not connected and to check the cable. I did that with several different cables and tried the usual router and modem reset. Only through trial and error did I find that I could connect to port 4 which is why I am able to write this post. What could have changed to disable ports 1-3 and can I get them working again? No issues with wireless connectivity.
View 3 Replies
View Related
Feb 12, 2013
I have a P7H55 Asus Motherboard with the Ethernet port and cable working fine individually. However, when i connect them together,the Ethernet light on the router remains stable as if connected but still the desktop shows not connected. i have installed the drivers which came from the motherboard manufacturer and are the latest.In the Network and Sharing Center, the icon is enabled.It does not show cross sign.
View 1 Replies
View Related
Apr 4, 2013
I have been using my laptop since a year now and yesterday suddenly my internet stopped working. On top of the connectivity bar a yellow sign appeared. Now my internet status is "No internet access" but when i connect my ethernet cable the internet starts working and i can see the "Internet access" status. I have re-installed my wi-fi driver too from the orignal CD that i got with my laptop, but still no luck also i did not install anything in past 1 week and the only anti-virus i have is Avast (tried disabling it too). I plugged out the cables from my router and plugged them again but that dint work too. There are 2 other laptops (running on windows 7 just like mine) on which the wifi connection is working but on mine it is not working.
View 9 Replies
View Related
Feb 10, 2013
I have a P7H55 Asus Motherboard with the ethernet port and cable working fine individually. However, when i connect them together,the ethernet light on the router remains stable as if connected but still the desktop shows not connected. This time i have installed the drivers which came from the motherboard manufacturer and are the latest. In the Network and Sharing Center, the icon is enabled. It does not show cross sign.
View 10 Replies
View Related
Nov 9, 2012
I have Lenovo laptop and my internet works just fine when the cable is connected but Wifi does not work. It shows that i have excellent signal on the side but it just wont connect. When i type in password it says " Windows cannot connect to XYZ ". I use Windows 7 and my wireless network adapter is Atheros AR9285.
C:UsersMY>IPCONFIG/ALL
Windows IP Configuration
Host Name . . . . . . . . . . . . : MY-PC
[Code]......
View 14 Replies
View Related
Jun 10, 2012
So I have a Westell 7500 Modem/Router with Century Link DSL. I've been running a couple of laptops and my wifi enabled TV on the wireless. A few days ago I got a new desktop PC (Windows 7) and plugged the ethernet cable into it. Everything was great but the wireless was a bit slow for the TV so I plugged that in with an ethernet cable too. No problems for a few days. Today, we had a power blip and everything reset and I noticed that the internet light on the modem was solid red and I couldn't access the internet on any machine (ethernet or wifi). I called the ISP who said there was an outage in the area. A few hours later, solid green light on the modem BUT the TV (ethernet connected), my iphone, and my laptops could NOT connect, despite the network showing up with a full signal. Oddly, my new PC, connected via ethernet was fine so I played some Diablo (side note). Here's the deal: the new PC connects just fine but nothing else will. If I unplug the ethernet cable to the PC or disable the LAN connection, the red internet light appears on the modem. It seems as though the PC has hijacked the modem in some way. Even the TV won't connect with the ethernet cable. The only way the internet works now is if the modem is connected to the new PC. I've done all the resents - unplugged the modem and let it sit for 10-15 minutes, accessed the router settings, etc etc. Why would this start happening now after everything was working well for several days and how do I fix it? I need the wifi connection! Update: Plugged my Macbook Pro into the ethernet cable (took it out of new PC) and it works.
View 1 Replies
View Related
