Cisco Wireless :: 2600 APs - Getting PoE From Switch But No Ethernet
Dec 10, 2012
I have a couple of 2600 APs (external antenna) which are getting PoE from my switch but no ethernet. This is happening on both APs. If I connect a laptop to the (cat5e) cable I get ethernet. If i move the AP to another patch lead adjacent to my switch I get ethernet connectivity too. So, change the cable is the answer I thought, however I have exactly the same issue on both APs and each ethernet cable has been reterminated a number of times (straight through). I wonder is the 2600 AP less tolerant to the actual ethernet cable ?
I just swap the cable, however the patch leads have been run (only 15m or so) and have been replaced once - relaying again is not an easy job. It's more a case of reterminating the cable that is already there and as I've already done this a few times on each patch lead and the results are the same each time I'm thinking I'm missing something obvious.
View 10 Replies
ADVERTISEMENT
Jun 5, 2011
trying to establish a connection on an ibm 3745 controller via two IBM 5822 modems to a cisco 2600 router using sdlc encapsulation secondary bridging data from the serial port to the E/Net port to run the 3270 client ???
View 19 Replies
View Related
May 2, 2012
I have a Cisco 2600 series with 2 X Fast Ethernet ports and I would like to configure the cisco to perform the task if it is possible.The scenario is:
2 networks:
F0/0: 192.168.x.x
F0/1: 10.1.x.x
No communication between them except one way multicast from F0/1 to F0/0.
View 1 Replies
View Related
Feb 14, 2012
does Cisco 2600 series switch support 802.1x and DHCP snooping?
View 6 Replies
View Related
Jan 10, 2012
My network generally runs older routers (2600 series) with 16 port switch modules (NM-ESW-16). This has always worked great since I can configure the router and the switch ports on the fly, making changes to either as necessary. Well I am upgrading to 2811 routers, and we wanted to get gigabit ethernet ports on our switch modules. I think I made an error when I purchased a few of these switch modules: NME-16ES-1G.
The first problem, is that the switch ports don't even show up on the router config, I have to establish a session into the switch, (And I can't seem to get back to the router unless I manually switch off power and restart). I don't like this type of switch module, it's like I'm running a completely separate device, and while having a layer 3 switch is cool, It doesn't let me setup routing protocols so I don't like doing it this way. I want to go back to using a switch module that simply adds a ton of ports to my router like the NM-ESW-16. (Note: The NM-ESW-16 does actually work in the 2811 and would be perfect if it were Gigabit speed.)
The seconds problem is that the NME-16ES-1G isn't actually a Gigabit switch. It has a single gigabit port, but the 16 ports are all Fastethernet, and not gigabitethernet. So ideally, I am looking for a switch module that I can fully configure from the router interface that has 16 gigabitethernet ports, and works with a 2811. IE I want to do this. [code]
View 4 Replies
View Related
Jun 17, 2012
My main PC and modem is in a back room of the house, my secondary PC and game systems are in the living room.My main PC HAS to have a wired internet connection because that is what I want.My game systems and second PC need a wired connection.I would like to have my D-Link wireless router in the living room so I can use the WiFi for my iPods, iPad, laptop, and anything else that I am looking at when I am sitting on the front porch. I have an Epson printer that I can hook up to my network that I want to be in the back room with my main PC.To get the internet into the living room I am going to run a CAT5E ethernet cable under my house (off the ground and away from electric wires and copper pipe) from my back room to the living room.Is it possible for me to go from the modem to a switch box (I actually have two switch boxes, but I believe I will only need one)which would be connected to my main PC, the printer, and the ethernet wire going under the house to the living room... Then in the living room have the wire that comes from under the house (from the back room) go directly into the wireless router and then from the router have cables going to my game systems and the second PC?If this will work, will I still be able to control the wireless router with my main PC?
View 9 Replies
View Related
Oct 2, 2012
OK i'm re-organising my network setup, most of my devices in my room are hard wired through Ethernet but some devices in the house need to run wireless.Currently i am running a super hub that has been configured into just modem only and a wireless router that gives wireless and hard wires up to 4 devices. Im wanting something that can be mounted out the way like an Ethernet switch but give it wireless accessibility too. I see you can buy access points to connect to your Ethernet switch device but will it give ample wireless connectivity if im running 4+ hardwired devices?I have recently been upgraded from 30Mbps to 60Mbps, this is fed from cable connection to the modem.
View 5 Replies
View Related
May 11, 2012
I have a Cisco WLC 2106 and I got 2 access points working, conected the controller (Aironet 1130AG), but I would like to know if I could connect a host or a laptop to the 2106 WLC.
I have a router conected to the WLC using the port 1, and the APs are in ports 7 and 8, but when I plug a pc in the port number 3, I do not get and IP from DHCP server, (DHCP is giving by the router). Im not sure if the 2106 WLC ports are for connect other network devices like a pc... I would like to know if there is a way to configure the controller to conect a host or a pc to the ethernet ports.
View 5 Replies
View Related
Feb 6, 2013
I have a situation where my Cisco 5508 did not come with SFP by default.
Can i use the SERVICE PORT to connect the WLC to the Switch
1. the controller has 8-SFP Slots
2. one service Port
3. On redundant Port
View 11 Replies
View Related
Dec 29, 2011
In my main office, I have a cable modem which is connected to my main E4200 router. All of my equipment (except my Ooma) is served by the E4200. The E4200 broadcasts a wireless network.In my basement, I have a Wii / entertainment center. The E4200 signal from upstairs isn't strong enough to stream video.
I bought the WET610N and have successfully set it up to interact with the E4200 wirelss network. I can hardwire my laptop to the WET610N and verify the internet works greatHowever, the Wii must connect over wireless. I have other equipment in the basement which would benefit from an internet connection. So, I want to A) connect the ESXS88W 10/100 8-port workgroup switch I have to the WET610N *AND* also broadcast a wireless signal in my basement (assuming the wireless network I see in the basement is the same "old" one from upstairs which has not benefited from the WET610N).
How can I set up my WRT54G2 to broadcast a wireless signal in the basement so that it leverages the E4200 signal served by the WET610N, while also having the workgroup switch offer hardwired connections to my other equipment (like Dish Network receiver)? It doesn't seem to work by just plugging the WRT54G2 into the workgroup switch.
View 2 Replies
View Related
Aug 12, 2011
can a poe switch be connected to an Ethernet switch
View 1 Replies
View Related
Aug 3, 2012
my computer doesn't have a COM port, so i connected an EthernetCOM cable to my laptop (ehternet end) and COM to the switch. Question now is, how can i establish connection?
View 2 Replies
View Related
Aug 8, 2012
I have a Ethernet module (SM-ES3G-16-P) installed in a 3945 router and noticed during first boot no licenses are active at all. I would assume at a mimimum ipbase would be active. With this module, does static routing work with just ipbase?
Example:
interface g0/1
no switchport
ip addr 192.168.254.2 255.255.255.0
[code]....
View 3 Replies
View Related
Feb 25, 2013
I contact you due that I’m currently configuring a Router Cisco 2921 with an Etherswitch module. The specific inventory of Router Cisco 2921 is:
Router#show inventory,NAME: "CISCO2921/K9 chassis", DESCR: "CISCO2921/K9 chassis"
PID: CISCO2921/K9 , VID: V06 , SN: XXXXXXXXXXX
NAME: "High Speed WAN Interface Card - 1 Port Gigabit Ethernet on Slot 0 SubSlot 0", DESCR: "High Speed WAN Interface Card - 1 Port Gigabit Ethernet"
PID: HWIC-1GE-SFP , VID: V01 , SN: XXXXXXXXXXX"
[Code]....
View 1 Replies
View Related
Jul 29, 2012
We have 2 internet providers and I would like to find some way to switch our 5 computers between the 2 internets without having to unplug the ethernet cables everytime someone wants to switch. Is there some type of switch we can buy for each computer to do this or is there no such thing?
View 8 Replies
View Related
Oct 10, 2012
I have a school club, but our school does not allow any wireless networks within the school perimeters.Wired are allowed, but wireless are not allowed.I plan to host a LAN party for my club, and we will have about 20-30 people.We cannot have any internet access, and I have not touched a wired stuff, There is a 24 ethernet switch, and if I buy one, and suppose I buy another 24 ethernet switch (I know there is a 48 ethernet switch), can I connect those two 24 ethernet switches to make 47 ports?* For a LAN party without internet access, can we use an ethernet switch or do we use something else?* For 20-30 people, it is recommended that we have a ~8mbps upload speed. When ethernet switches advertise 10mbps, is that upstream & downstream? When all the computers are hooked to 24 ports, does the advertised 10mbps go lower? (I have seen 100/10 mbps, and I don't know what that means)
View 4 Replies
View Related
Mar 27, 2012
Via ethernet which cable is use between printer to switch
View 1 Replies
View Related
Jan 6, 2012
I have a D-Link Ethernet Switch. I have my computer and a Roku hooked to it. I tried hooking Another Roku and it cannot hook to Network. I unplugged my old Roku and hooked the new one and no problem. Just can't hook both up at once. Is there something I should be doing to enable this? I am allowed 4 computers through my network.
View 7 Replies
View Related
Jan 15, 2011
If I can use my switch as a router or a way to get more Ethernet port? Since my router is down for the count and I need more ports!
View 4 Replies
View Related
Jan 9, 2011
I'm going to be wiring a new (to me) house with a couple cat 6 runs to each room. The runs will all be brought back to an enclosed 6u rack and cat 6 110 style patch panel. This rack will contain:
- HP 2824 Switch
- PfSense router (Supermicro X7SPA-HF ITX board)
- DSL modem
Since the rack is completely metal and enclosed I'm going to put my Netgear WNDR3700 WiFi router (used as an access point only) on top of the rack. My question is, what the implications are in regards to placing a WiFi device right next to a bundle of ethernet cables?
View 4 Replies
View Related
Mar 23, 2012
Im having a ACT Broadband internet connection, he provides internet connection through a wire which runs into my room that can be directly connected to the my computers NIC. Whenever i switch on my computer and opens the browser it first redirects to the page url... where it asks for Username & Password, our ISP gives us a IP Address which displays on the web page after logging in.I want the internet connection to be shared with my roommates so i bought a 8 port Ethernet switch (url..), which is having a uplink port also. I have connected the wire given by the ISP to the up link port of the switch & i connected my PC to one port of the switch with another network cable. I also connected my friends PC to second port of switch with another network cable, my problem is that when i sign into my ISP web page and start using the internet & my friend also wants internet in his PC & when he opens the browser the ISP's webpage is appearing and when he sign's in internet is disconnecting in my Pc. I tried to change the IP but as a default IP is given by the ISP if change the IP internet is not working.
View 3 Replies
View Related
Jan 13, 2012
I connected a switch and the device is not even recognized in my router site.
View 12 Replies
View Related
Feb 21, 2013
I bought a "Nexxt Solutions 8 ports Ethernet Switch" and it only allows me to use the internet on the first computer that I plug into one of the Lan ports. I get a Limited Connection MessageI did some research and found something about a DHCP Server and automatic IP assignment, but I can't find a comprehensive tutorial on how to setup this.I'm sure the solution is simple.
View 2 Replies
View Related
Jan 7, 2011
So my old router needed replacement and my dad bought a Netgear gigabit ethernet switch instead of a router. It said that it gets 1Gbps when I look inside the local area connection speed. The problem was we tried to use it like a router but only 2 computers could connect to the internet at one time but it was indeed noticeably faster when it came to video streaming speed. We since returned it and bought a Netgear N600 router that says the speed is 300mbps but like my old router it shows the speed is actually 100mbps and the streaming is good for the most part but every now and then slows down. Would using the ethernet switch with our new router work with streaming speeds and connection stability and of course let more computers connect and also use the routers wireless.
View 13 Replies
View Related
Jan 30, 2012
Today my sw upgrade procedure failed on a ME3600 Series switch.
From the past with LAN switches i thought that we need to set IP settings manually in ROMMON and then load remotely an IOS via TFTP.
But it seems that this is not supported there.So now i would like to ask how can i bring a bootable IOS to the ME3600 switch. and at least: how can i bring back my switch to life.
I could imagine that there is a missing default gateway.But what is the syntax for default gateway? And after I have connectivity i need to work for the process of loading a bootable image to the switch.
View 3 Replies
View Related
Aug 9, 2011
I want to connect internet via telephone cable by using rj11 jack from my ethernet switch to another computer it is 150mts away from my office premises.
View 1 Replies
View Related
Oct 28, 2011
I have seen 5-port network switches (for home network use)for sale that list CAT5 and CAT5e as the cabling. My question is, can CAT6 cable be used with these switches without performance issues?
View 1 Replies
View Related
Feb 8, 2011
I have a 3640 router with 4 Fast Ethernet Network Modules (1fe-tx, 1fe2w & 2fe2w-v2) and a Catalyst 2912 switch. I can not acheive a link between the 2 devices. All four will not get a link light and the interface(s) show no errors. If I plug the Router nic into virtually any other switch or workstation it works flawlessly. I put a switch between the catalyst and the 3640 and it works without error.
Steps I have tried...
1. Configure interfaces on both Switch and Router to Auto Speed, Auto Duplex2. Configure interfaces on both Switch and Router to speed 100, Full Duplex3. Try Both Crossover and Straight-Through verified working cables.4. Tried a second 2912xl-en switch
Both 2912 switches are factory defaulted, other then the changes I made to the speed and duplex to try to get them connected.Both the router and switches have been doing other functions (seperatlly) within our network for years?So my question is...Why is the NICs in the router compatible with every other vendor other than CISCO?
View 5 Replies
View Related
Apr 16, 2013
we have some (2) HP Notebooks with a Broadcon 4313 b/g/n WLAN Chip and use the latest drivers (2012). This Chip can provide up to 72 mbit/s with 2,4 ghz.
If we connect this notebooks to a Aironet 2600 AP (10 feet distance) the Windows 7 WLAN Dialog shows 72 Mbit/s for 3 seconds and than only 5.5 Mbit. Others (newer) Laptops show 450 Mbit. The WLAN works with WPA2/AES and PSK. The speed doesn't go up, if we copy a big file to the laptop.
Here is the Linktest from the AP to Client (from the WLC 2504 Webinterface):
View 12 Replies
View Related
Feb 13, 2013
is it possible to plug a cisco aironet ap 2600 to a Cisco-Switch with PoE capabale port and give power to the Cisco AP-2600 through the switch port ? if yes, what is the exact switch part-number so that i can order one?Currently i have a Cisco Cat 3550-24 , does it support PoE?
View 2 Replies
View Related
Apr 19, 2013
We have recently deployed Cisco APs (2600 series) in our org. but we are facing alot of bandwidth/speed issues. when a single user is copying or pasting any data into the network, the speed seems ok, but when multiple-users start copying data , so the data-rate speed gets slower and slower as the users are increasing.
Can any one tell me what is the issue? Why the internal data rate speed gets shared between users? i think each user should bydefault get any specific data rate speed, but that is what not happening on our end.
View 6 Replies
View Related
Jul 23, 2012
I'm watching a video streamed from my laptop and the signal is constantly being dropped. I suspect the D-Link DES-105. I have another Ethernet switch on the system as well but it is a Gigabit unmanaged switch from D-Link and has worked well with video streams. I've removed the DES 105 from the circuit and videos play fine. Should I dump to DES-105 for another Gigabit switch? SOme say I have a bad cable somewhere but I have tested all and have not found a problem.
View 2 Replies
View Related
Nov 4, 2011
I have setup an Asus RT n16 with 3 computers that support gigabit ethernet and a media server on one floor. On the other floor I have set up a fast ethernet switch (connected to my asus router) which is connected to several fast ethernet enabled computers.
Would the fast ethernet devices slow down the entire gigabit networking to 100mbps connections on my floor - similar to how a wireless n network running at 300mpbs must slow down to 54mbps when a wireless g device is connected to it?
View 6 Replies
View Related
