Cisco WAN :: 3640 Router / Catalyst 2912 Switch - Ethernet Link?
Feb 8, 2011
I have a 3640 router with 4 Fast Ethernet Network Modules (1fe-tx, 1fe2w & 2fe2w-v2) and a Catalyst 2912 switch. I can not acheive a link between the 2 devices. All four will not get a link light and the interface(s) show no errors. If I plug the Router nic into virtually any other switch or workstation it works flawlessly. I put a switch between the catalyst and the 3640 and it works without error.
Steps I have tried...
1. Configure interfaces on both Switch and Router to Auto Speed, Auto Duplex2. Configure interfaces on both Switch and Router to speed 100, Full Duplex3. Try Both Crossover and Straight-Through verified working cables.4. Tried a second 2912xl-en switch
Both 2912 switches are factory defaulted, other then the changes I made to the speed and duplex to try to get them connected.Both the router and switches have been doing other functions (seperatlly) within our network for years?So my question is...Why is the NICs in the router compatible with every other vendor other than CISCO?
View 5 Replies
ADVERTISEMENT
Oct 17, 2011
i have 2 x T1 terminating on border router cisco 3640 route. (configured using multilink interface). Our IP block is routed on this bundled T1 circuits by At&T. I want more internet bandwidth.
1. Can i connect my DSL (on ethernet interface and using static DSL IP) on the same router and confgure two static routes to internet - one to multilink interface and other to ethernet interface (connected to DSL) ?
2. I have many servers using static NAT to external IPs which are routed on T1 circuits. Will it get into issues when communicating to outside? [for example my exchange server, websites etc?
View 6 Replies
View Related
Apr 28, 2013
I'm using 3640 router running on c3640-js-mz.124-25d.bin IOS. I'm using NM-1A-OC3SML= (ATM OC3, long reach single mode) interface card. Now my pc is connected an fast ethernet interface of the router. Need to know the ATM configuration on this cisco 3640 router in order to achieve the ATM over ethernet traffic get success. As of now i've confugred as below but it's not working it seems.
interface ATM2/0
bandwidth 120000
ip address 10.2.2.1 255.255.255.0
no atm ilmi-keepalive
pvc 0/36
protocol ip 10.2.2.10 broadcast
cbr 70000
encapsulation aal5mux ip
let me know the correct encapsulation type for the connectivity.
View 2 Replies
View Related
Dec 5, 2011
My customer wants to replace some Cisco 2912 by new routers, but I can't find a way to add Token ring Network Module on 2951 or 3925 routers with the Cisco configuration tool.Does token ring is still supported on ISR G2 routers?
View 5 Replies
View Related
Jul 23, 2012
I'm watching a video streamed from my laptop and the signal is constantly being dropped. I suspect the D-Link DES-105. I have another Ethernet switch on the system as well but it is a Gigabit unmanaged switch from D-Link and has worked well with video streams. I've removed the DES 105 from the circuit and videos play fine. Should I dump to DES-105 for another Gigabit switch? SOme say I have a bad cable somewhere but I have tested all and have not found a problem.
View 2 Replies
View Related
Oct 24, 2012
We have a location that currently has one frame T1 and 4 point-to-point T1s. We are looking at adding a second frame T1 to be bonded with the first. Currently, we have an old 3640 router, so I am thinking this would be a good time for an upgrade. Cost is a concern, so I am hoping to buy something refurbished that is newer than what we have now but is not going to cost a ton as buying new would. My thought is either a 2821 or 2921 with 2 HWIC-4T1/E1. I am not familiar with this HWIC just wanting to make sure this a good solution for our situation.
View 8 Replies
View Related
Nov 20, 2009
I have a Catalyst 4006 switch in production and a spare switch of same model. I have to quickly copy the configuration from production switch to spare switch (both L2 and L3 configurations) How do I do that?
View 6 Replies
View Related
May 13, 2012
i have configured a cisco router with the following configuration to practice obtaining certificates from a microsoft 2008 server configured as a stand alone CA.this part works okay but what i am trying to do next is giving me a headachei am trying to delete the identity certificate but am having no luck whatsoever
interface FastEthernet0/0ip address 192.168.2.1 255.255.255.0ip nat outsideno shut
interface FastEthernet0/1ip address 192.168.1.1 255.255.255.0ip nat insideno shut
access-list 101 permit ip 192.168.1.0 0.0.0.255 192.168.5.0 0.0.0.255
access-list 102 deny ip 192.168.1.0 0.0.0.255 192.168.5.0 0.0.0.255access-list 102 permit ip 192.168.1.0 0.0.0.255 any
[code].....
i entered the following commands on the router to delete the certificatebut as you can see its telling me the certificate dosn't exist(this method of deleting the cert has come from Richard Deals complete cisco vpn configuration guide) 3Purley(config)#crypto ca certificate chain PurleyPurley(config-cert-chain)#no certificate 61E0446A000000000002% Certificate not found.ps the router is a 3640 running c3640-jk9o3s-mz.124-7.bin
View 1 Replies
View Related
May 14, 2011
I have been confronted with an issue recently with two of my 3640 series router reloading endlessly.Initially i thought it could be a matter of MEM not well seated, but unfortunately it wasn't the problem.i have attached the gibberish produced when these routers are booted up.Be informed as well that these devices are loaded with max MEM.
View 1 Replies
View Related
Sep 23, 2012
The Cisco 3600 series (3640) is hanged during booting proccess, the IOS is decompressed, but after some text it hanges and I even cannot go to user exec. ROMmon and bypassing the config setting, but the result is still the same.
View 5 Replies
View Related
Feb 25, 2013
I contact you due that I’m currently configuring a Router Cisco 2921 with an Etherswitch module. The specific inventory of Router Cisco 2921 is:
Router#show inventory,NAME: "CISCO2921/K9 chassis", DESCR: "CISCO2921/K9 chassis"
PID: CISCO2921/K9 , VID: V06 , SN: XXXXXXXXXXX
NAME: "High Speed WAN Interface Card - 1 Port Gigabit Ethernet on Slot 0 SubSlot 0", DESCR: "High Speed WAN Interface Card - 1 Port Gigabit Ethernet"
PID: HWIC-1GE-SFP , VID: V01 , SN: XXXXXXXXXXX"
[Code]....
View 1 Replies
View Related
Jan 15, 2011
If I can use my switch as a router or a way to get more Ethernet port? Since my router is down for the count and I need more ports!
View 4 Replies
View Related
Jun 17, 2012
My main PC and modem is in a back room of the house, my secondary PC and game systems are in the living room.My main PC HAS to have a wired internet connection because that is what I want.My game systems and second PC need a wired connection.I would like to have my D-Link wireless router in the living room so I can use the WiFi for my iPods, iPad, laptop, and anything else that I am looking at when I am sitting on the front porch. I have an Epson printer that I can hook up to my network that I want to be in the back room with my main PC.To get the internet into the living room I am going to run a CAT5E ethernet cable under my house (off the ground and away from electric wires and copper pipe) from my back room to the living room.Is it possible for me to go from the modem to a switch box (I actually have two switch boxes, but I believe I will only need one)which would be connected to my main PC, the printer, and the ethernet wire going under the house to the living room... Then in the living room have the wire that comes from under the house (from the back room) go directly into the wireless router and then from the router have cables going to my game systems and the second PC?If this will work, will I still be able to control the wireless router with my main PC?
View 9 Replies
View Related
Jan 7, 2011
So my old router needed replacement and my dad bought a Netgear gigabit ethernet switch instead of a router. It said that it gets 1Gbps when I look inside the local area connection speed. The problem was we tried to use it like a router but only 2 computers could connect to the internet at one time but it was indeed noticeably faster when it came to video streaming speed. We since returned it and bought a Netgear N600 router that says the speed is 300mbps but like my old router it shows the speed is actually 100mbps and the streaming is good for the most part but every now and then slows down. Would using the ethernet switch with our new router work with streaming speeds and connection stability and of course let more computers connect and also use the routers wireless.
View 13 Replies
View Related
Oct 1, 2012
i am running c3640-is-mz.124-21.bin on a cisco router 3640. i am trying to create a monitor session in the CLI and everytime i type the command Router(config)#monitor session 1 interface ethernet2/1 % Invalid input detected at '^' marker. Router(config)#monitor session 1 interface ethernet2/1 ^% Invalid input detected at '^' marker. i get the error invalid input ?
View 10 Replies
View Related
Dec 18, 2012
I have a 2821 router and need to add another Ethernet port.
However, all the Ethernet modules seem to be End of Sale and the suggested replacements are only compatible with the ISRg2 range.
View 2 Replies
View Related
Dec 29, 2011
In my main office, I have a cable modem which is connected to my main E4200 router. All of my equipment (except my Ooma) is served by the E4200. The E4200 broadcasts a wireless network.In my basement, I have a Wii / entertainment center. The E4200 signal from upstairs isn't strong enough to stream video.
I bought the WET610N and have successfully set it up to interact with the E4200 wirelss network. I can hardwire my laptop to the WET610N and verify the internet works greatHowever, the Wii must connect over wireless. I have other equipment in the basement which would benefit from an internet connection. So, I want to A) connect the ESXS88W 10/100 8-port workgroup switch I have to the WET610N *AND* also broadcast a wireless signal in my basement (assuming the wireless network I see in the basement is the same "old" one from upstairs which has not benefited from the WET610N).
How can I set up my WRT54G2 to broadcast a wireless signal in the basement so that it leverages the E4200 signal served by the WET610N, while also having the workgroup switch offer hardwired connections to my other equipment (like Dish Network receiver)? It doesn't seem to work by just plugging the WRT54G2 into the workgroup switch.
View 2 Replies
View Related
Dec 19, 2010
We want to terminate new 10M link via Ethernet interface on Cisco 1841 router. We have free Gig port on the router. We also have HWIC-FE module inserted in the router. However, our implementation team said that Cisco 1841 doesn't support 10M link. It is not designed to cater to such high Bandwidth.
View 14 Replies
View Related
Sep 1, 2007
Can we force the Gigabit Ethernet port to be 1000 full duplex in Cisco Catalyst Express 500 series?
View 3 Replies
View Related
Dec 10, 2012
I have a 2960S Catalyst switch in my LAN, with the firewall and the servers in the same VLAN (vlan 3).All the servers and the firewall are in the vlan 3 are in the "192.168.19.0/24" subnet, the firewall has the IP "192.168.19.1".I can land on the firewall with a VPN (192.168.130.0/24) which has a complete view on the subnet 19/24.I can access, manage and get SNMP information of the Catalyst from the servers but I can't do the same from the VPN.Is there some feature I need to enable on the switch in order to allow 192.168.130.0/24 to access it?
View 4 Replies
View Related
Dec 27, 2010
I just started configuring my cisco catalyst 2950 switch. Basically im preparing for my CCENT exams my basic configuration is as follows.
-My Laptop is connected to the console port
-I'm connected to the internet via my wireless
-I'm connected to the switch port via my NIC card
View 4 Replies
View Related
Aug 12, 2011
can a poe switch be connected to an Ethernet switch
View 1 Replies
View Related
Apr 23, 2012
I have a situation where I have tenants connecting to my wireless network and paying towards the internet bill. I am able to control this by using MAC filtering, but I have just realised that this only works for wireless clients.
Is there a way to replicate this for the router's Lan ports? Or possibly even just disable Lan access. The router model is a D-link DSL-2750U.
View 2 Replies
View Related
Mar 3, 2011
I have two computers in the house which are linked by an ethernet cables, my wireless router only has one ethernet hole,so I would like to know what I need to buy? such as an adapter or something, so I can have two ethernet cables to connect to my router.the type of router I have is called a Hauwei echolite HG521 broadband wireless ADSL2+ router.
View 1 Replies
View Related
Jun 15, 2011
I recently bought a tenda w548d Version 2.0 Adsl2+ Modem router. it worked fine with its default settings and wired connection was ok when i chose DSL uplink while installing its driver from CD. But it couldn't connect wireless. There were strong signals but connected computer couldn't get access to the internet. so i tried using ethernet uplink instead of DSL uplink while reinstalling the software Since then the light of ADSL never lights, even it never blinks. now the software on the cd can connect to the router. i cannot access its settings using IP address in browser, the page wouldn't load. I am so worried. Can i revert the setting back to dsl uplink?I can connect to the internet very smoothly using my old router so you can't blame my phone line or lan wire. I have tried reset the new router many times but still the ADSL light never lights up. And the ADSL light is ok because when i turn the router on, it lights with all the others.
View 2 Replies
View Related
Oct 18, 2012
I'm trying to configure Catalyst 2960 series 8 port switch in my office. I have just plugged in switch and started and then put Ethernet cable (which is coming from the wall port (LAN) into CONSOLE (switch). and connected my laptop's ethernet cable to switch's 1x por
View 16 Replies
View Related
Jun 13, 2012
I'm having trouble setting up SSH on my new Switch.
no aaa new-model
aaa authentication login default local
ip domain-name king.local
[Code].....
I would like to be able to use Vlan 10 192.168.155.1 for SSH remote management.
View 11 Replies
View Related
Jun 18, 2012
is there a discover tool for such a switch, i forgot the assigned ip .
View 2 Replies
View Related
Feb 21, 2011
we are using the catalyst 3550 L3 for BGP routing. For e.g. Gi 0/4 is our internal interface tha we want "switch".
We need on Gi 0/5 the same network that is on gi 0/4.
How is it possible? Make it like a 2 port mini switch. Or make a bridge of these 2 interfaces without any complicated reconfiguration needed?
View 2 Replies
View Related
May 23, 2013
I'm trying to do password recovery on a Catalyst 3850 switch..I've read the section in this: url...where it says that I need to have physical access to the switch (I do), and that I reset the password if I issue a break command and interrupt the boot procedure. I've tried to do that... it gives me the "switch:" prompt, so I think I've interrupted the boot procedure successfully, but, what do I do next?I've successfully done recoveries on Catalyst 2950s, 3550s & 3560s, but the procedure for this one, if I'm reading the link above right, sounds like it's completely different.
View 10 Replies
View Related
Aug 20, 2012
i try to implement layer 2 qos in 2960. when i complete to configure the switch, i want to test the qos.PC1 conect to switch port 1,PC2 conect to switch port 2 . PC1 is source teminal. i use skydata.exe and FTP for the test.
when use the skydata ,the PC2 speed can reach 10mbps.when use the FTP , the PC2 only can reach 1.2mbps. why?
View 3 Replies
View Related
Jan 22, 2011
I have Cisco Catalyst 2901 switch with Sup engine which have CatOS installed. I want to know that can I install Cisco IOS in this switch.
View 1 Replies
View Related
Sep 10, 2011
Working on my CCNA w/ live equip, I accidentley deleted the hardware IOS- yes, beginners mistake. Upon bootup, I do not get a command prompt. I tried the recovery procedure(hold mode button before power up) recommended by Cisco to no avail. My issue is I use SecureCRT & the charaters/font is ineligible. Here is an example of what I see when typing; "þæb Bûÿÿûýÿ¿¿ÿÿ". Currently, the SYST indicator is blinking & I have no access.
View 3 Replies
View Related