Cisco Switching/Routing :: Creating A Span Port On Router 3640

Oct 1, 2012

i am running c3640-is-mz.124-21.bin on a cisco router 3640. i am trying to create a monitor session in the CLI and everytime i type the command Router(config)#monitor session 1 interface ethernet2/1 % Invalid input detected at '^' marker. Router(config)#monitor session 1 interface ethernet2/1 ^% Invalid input detected at '^' marker. i get the error invalid input ?

View 10 Replies


ADVERTISEMENT

Cisco Switching/Routing :: VTP Traffic Not Seen On SPAN Port On 3750

Dec 12, 2011

Been dealing with a strange problem for several days now.  It started out with a problem that I thought was VTP related but ended up being something else.  I setup a span port on a 3750 that I am connected to that was mirroring the trunk connection coming into the switch.
 
Never saw an VTP traffic come across the connection but doing a sh vtp status indicated the traffic was arriving and getting processed.  When I found some debug commands (debug sw-lan vtp), I was also able to see the packets go between switches.  Seeing this issue concerns me that there is other traffic that isnt showing up during a span session.
 
I know that doing a span on a switch, especially using a trunk port as a source, isnt a good idea.  Since I didnt have a TAP at time, this was my only choice.  I have since borrowed a NetOptics TP-CU3 tap from a good friend and was able to confirm the VTP traffic was going across the trunk connection between switches.
 
All of my 3750's are running 12.2.55.SE.

View 8 Replies View Related

Cisco Switching/Routing :: SPAN Port Configuration On 3750?

May 23, 2012

I'm trying to configure a mirror port on a 3750. This configuration needs to replicate data from local ports, but I need that also act as a regular access port.
 
With the initial configuration, SPAN port, there is no problem, all the data of the configurated ports is replicating in the configurated port. On the port configurated as mirror there is a PC connected for audio recording. When the port is not operating as SPAN there is communications without problem over the LAN. But when I configure the port as SPAN, communication is interrupted.
 
Here is the actual configuration:
 
SWITCH1-PISO7#sh monitor session 1
Session 1
---------
Type                   : Local Session

[Code]......

View 5 Replies View Related

Cisco Switching/Routing :: 2960 -Destination Port Not Responding Over SPAN

Jun 8, 2012

i have configured SPAN over cisco 2960 to monitor source port traffic but after configuration i dont able to get response from destination port  as my NMS is attached on destination port so i lost its web interface.
 
Configuration is as under.
 
monitor session 1 source interface gigabitEthernet0/5  (Source Port on Vlan 100) monitor session 1 destination interface gigabitEthernet0/1 (Destination Port on Vlan 200)

View 2 Replies View Related

Cisco Switching/Routing :: NEXUS 7k Span Session Getting Twice Data To Port

Jun 9, 2013

I'm setting up a montitor session on a NEXUS 7K as below.we are receiving in 150M of data and 0 data going out port 9/25.but port 4/24 shows 300M to the span port?

View 1 Replies View Related

Cisco Switching/Routing :: Configuring Span Port On 6513 Switch

Mar 2, 2012

I have two servers, connected on two(Different) 6513 directly connected switches. Both these servers are in the same Vlan.
 
I have to monitor communication these two servers. I have a system connected on one of the 6513 switch, where network tool wireshark is installed.
 
How to configure span port.
 
switch 6513-1# show run int Gi10/43  --------------------Server 1 is connected
 
switch 6513-2# show run int Gi9/45 ------------------------Server 2 is connected
 
switch 6513-2# show run int Gi9/46 ------------------------System on which network tool wireshark is installed.

View 9 Replies View Related

Cisco Switching/Routing :: Effects Of SPAN Port Configuration On 4507R+E Switch?

Oct 29, 2011

I read quite a few documents on configuring SPAN on a cisco switch but none of them mention any limitations or any kind of CPU load it can have on a switch. I need to configure this on one of our switches and would like to know if there are any implications related to SPAN.

View 5 Replies View Related

Cisco Switching/Routing :: SPAN / Monitoring Destination Port Behaviour - 2960 LAN

Jan 16, 2012

In s SPAN session , normally the destination prt is used for monitoring purpose only. But could destination port be used to access the equipement or PC connected to that port , for a 2960 LAN BASE image  switch .

View 2 Replies View Related

Cisco Switching/Routing :: CAT6500 / Duplicate Multicast Packets On A Span Session Port?

Apr 17, 2013

If I monitor a trunkport on the rootbridge in both directions  I get Duplicate Multicast Packets on the perticular VLAN.   The first guess is, that this is worked as designed and not a IOS Bug (Platform CAT6500 SUP720 IOS 12.2(33)SXI9 ) Until know I only found an old Cisco press link from 2002 with this subject.

View 2 Replies View Related

Cisco Switching/Routing :: 1433 - Span Port Configuration To Listen To Specific Traffic Only?

Nov 2, 2011

Is it possible to configure the span(switch port analyzer) port and restrict it to only listen to ingress and egress of TCP/1433 from the source port?

View 2 Replies View Related

Cisco WAN :: 871 SPAN Want To Monitor The Wan Port Using Span

Apr 4, 2011

I am having some problems creating a SPAN port on my Cisco 871 (running IOS 12.4-11T).  My 871 is connected to a DSL modem, and uses "IP Negotiated" to get its dynamic ip address.I want to monitor the WAN port (FastEthernet4) using SPAN, but when I type "monitor session 1 source interface FastEthernet4" into the cli, it is rejected.  I can successfully use any of the other FastEthernet ports, as well as Vlan1 as a source for the SPAN session. I have tried to use Dialer0 instead of FastEthernet4, but it still doesnt work.

View 5 Replies View Related

Cisco Switching/Routing :: 3640 Router Hangs

Sep 23, 2012

The Cisco 3600 series (3640) is hanged during booting proccess, the IOS is decompressed, but after some text it hanges and I even cannot go to user exec. ROMmon and bypassing the config setting, but the result is still the same.

View 5 Replies View Related

Cisco Switching/Routing :: Can't Configure SPAN On 800 Series Router

May 1, 2013

I have a Cisco 881 router running 15.1(4)M4. I am trying to configure SPAN on it to mirror my outside interface (source) to one of my LAN interfaces (dest).
 
!--- WAN interface
interface FastEthernet4
description Comcast WAN$ETH-WAN$

[Code]......
 
As you can see from the above output there is a problem with the command on this interface. When I try to set Fa0 as my source it works fine:
 
rtr(config)#mon session 1 source int fastEthernet 0
rtr(config)#
 
Is this because fa4 is layer 3 and fa0 is a switchport? If so, is there another way to set fa4 as the source?

View 4 Replies View Related

Cisco Switching/Routing :: 3640 / ATM Over Ethernet Not Working

Apr 28, 2013

I'm using 3640 router running on c3640-js-mz.124-25d.bin IOS. I'm using  NM-1A-OC3SML=  (ATM OC3, long reach single mode)  interface card. Now my pc is connected an fast ethernet interface of the router. Need to know the ATM configuration on this cisco 3640 router in order to achieve the ATM over ethernet traffic get success. As of now i've confugred as below but it's not working it seems.
 
interface ATM2/0
bandwidth 120000
ip address 10.2.2.1 255.255.255.0
no atm ilmi-keepalive
pvc 0/36
  protocol ip 10.2.2.10 broadcast
  cbr 70000
  encapsulation aal5mux ip

let me know the correct encapsulation type for the connectivity.

View 2 Replies View Related

Cisco Switching/Routing :: 3640 Can't Apply Service-policy?

Mar 21, 2013

I got this 3640, trying to apply a service-policy (output and input), but seems like I do it something wrong...because he only apply the output policy... here the config, I already try to config the service police inside the fa0/0, but is not showed at all, he only show the output, its like I never apply that

View 1 Replies View Related

Cisco Switching/Routing :: System Crash 2611 And 3640

Apr 8, 2013

I got some unexpected System crash, and this happens to 2 different routers on the same network.. (We suffer a Crash and change the router, happens the same to the new router after some time, maybe 40 minutes!!)
 
Here is the last console report for the new router....
 
%Software-forced reload
 
Preparing to dump core...
4w1d: %SYS-2-WATCHDOG: Process aborted on watchdog timeout, process = IP NAT Age

[Code]....

View 3 Replies View Related

Cisco Switching/Routing :: 3640 Can't Route Traffic Until Pinging

Nov 1, 2011

We have a Cisco 3640 router running c3640-is-mz.123-3g.bin Switching ports are devided into several VLans. Each VLan has its own IP subnet. We can't ping IP address X in subnet A from subnet B unless we log into the router and ping it from there first. (and then the IP address will show up in "show ip arp" command. Then we can ping X in subnet A from subnet B, and browse web on device X from subnet B, etc. )

View 6 Replies View Related

Cisco Switching/Routing :: 3640 GLBP Working Now Want Interface Redundancy?

Dec 6, 2011

So I have 2 routers (cisco 3640) that each go to their own ISP and then back to the same switch.  I have setup ospf and glbp, and now have pretty good redundancy.  If either internet connection or routers go down everything is still golden. 
 
So I was thinking that if an interface went down then the router would not be load balanced with glbp which got me thinking whats the best way to get interface redundancy (and I was going to add a 2nd switch with the second interface).

1) Setup BVI on the 2 interfaces.
2) Setup a 2nd interfaces (on each router), I would have to split the subnet, for instance: [code]then the machines could be on the subnet 192.168.0. 0/23 and setup glbp for 1 ip across all 4 interfaces (I'm not even sure if you can do this but think it would work).
3) Is there a way to utilize etherchannel or anything like this
 
A negative to option 2 would be that if 1 of the interfaces went down, all the sudden 2/3 (or so) of your traffic would be going through 1 router.

View 5 Replies View Related

Cisco Switching/Routing :: 2600 / 3640 WIC-2T Configuring Serials Modules

Feb 5, 2012

How to configure my serial modules on my 2600 and 3640?  Each router has the WIC-2T with two cables connecting them.  I tried to ping one router from the other, but no luck. Serial IP address I just made up, this is my home lab, so if I messed those up some how,
 
Here is the running config for each rotuer:
 
2610:
Current configuration : 1071 bytes
!
version 12.3
[Code]...

View 22 Replies View Related

Cisco Switching/Routing :: 3845 / 3640 - GLBP - Weighting Based On Bandwidth For One PPP Of Many?

Dec 28, 2011

I have two routers at our core data center, a 3845 and a 3640.  These are configured with GLBP.  There are 4 remote sites:
 
Site #1: One T1 link to the 3825
Site #2: One T1 link to the 3825, and One T1 link to the 3640
Site #3: One T1 link to the 3825, and One T1 link to the 3640
Site #4: One fractional T1 link to the 3825, and One T1 link to the 3640.
 
My question regards site #4.  If i understand correctly, GLBP works on the premise of "host" balancing, and not true "load" balancing.  The reason I ask is that the large majority of our WAN traffic is from our Exchange server to our remote sites.  In the case of site #4, our exchange server is sending traffic on the fractional T1.  Is there any way with GLBP to either split this traffic from a particular host across two links in a round-robin fashion, but leave other hosts to travel wherever the router sends them, or, to force at least our exchange server to use the full T1, rather than the fractional?
 
I've read up on the weighting mechanism, and it appears that tracking an interface has nothing to do with bandwidth use.  If I understand correctly, if I were to track the Site #4 PPP to the 3640, and give a weight of 10 to glbp on there, it would really only take affect if the interface is down.  It will have nothing to do with host AVF election.For the record, exchange traffic is constant to this site, so there is no chance for the host connection to reset and potentially elect to use the larger pipe. I would like to "tweak" this to make better use of available bandwidth.

View 2 Replies View Related

Cisco Switching/Routing :: 3640 What IOS Version Can Support IPv6 RIP In Hardware Limit

Jun 25, 2012

I have the cisco 3640 with IOS Version 12.2(46) , and it with DRAM:32M , Flash:8M.What IOS version can support IPv6 RIP in the hardware limit?

View 3 Replies View Related

Cisco WAN :: ASR 1006 Supported Span Port Or Port Mirroring?

Mar 2, 2011

is ASR 1006 supported span port or port mirroring? Any config about that?

View 2 Replies View Related

Cisco Switching/Routing :: 6509 - Doing IDS Via SPAN Ports

Dec 13, 2011

I am hoping you can provide me with some opinions, feedback, thoughts on the following. We have some Cisco 6509 switches in our environment currently hitting around 60% usage on the Router overall statistics.
 
Now we are looking at implementing an intrusion detection system but by being as least invasive as possible to the network. Our thoughts are to utilize a SPAN port on the switches to send traffic to the NIDS device but we have concerns of the following. The limitations of SPAN sessions on 6509's . The overhead on the switch of turning a SPAN session on and leaving it on permanently.

View 1 Replies View Related

Cisco Switching/Routing :: Remote Span With C2960

Mar 12, 2013

I am trying to configure RSPAN for one of my client. They have Server-Client VTP architecture. Voice Recording Server is connected to C4507. Agents are connected to C2960 and C3750. I got 2 sessions configured and the connectivity is a as follows:

1. Voice Recording Server-----C4507-----C2960-----C2960-----Agent IP Phones (Session 1)
2. Voice Recording Server-----C4507-----C3750-----Agent IP Phones (Session 2)
 
Recording works with Session-2 but not with Session-1. I understand the problem could be due to multiple reasons: 1.1. C2960 is working in client VTP mode so i cannot add remote span command under the vlan configuration. 1.2. C2960 has LANLITE IOS image which i am not sure if it supports Remote Span.

View 2 Replies View Related

Cisco Switching/Routing :: SPAN Configuration In Catalyst 3750

Dec 31, 2011

I have CISCO catalyst with VLANs (VLAN ID 33, 36, 40-53) configured. I need to configure port mirroring in Switch 3750 for NAC (Network Access Control).  I need to Monitor all the VLANs. Here is the SPAN configuration of switch: [code] Monitor session 1 source vlan 33 , 36 , 40 – 53.Monitor Session 1 destination interface fa 1/0/8  (here I am not able to set encapsulation dot1q ) because the error occurred saying %one or more dest port do not support the encapsulation%.

View 5 Replies View Related

Cisco Switching/Routing :: How To Setup SPAN On 4900m Switch

Feb 12, 2013

I currently have IOS image cat4500e-entservices-mz.122-53.SG5.bin.  According to my research it appears SPAN is supported on this OS.  However, after looking at procedure notes using websites like here:

[url]... I cannot find and obviously not figure out how to use the SPAN  command.  My main objective is to simply setup a port mirror on one of my TenGigabitEthnet interfaces and from what I read SPAN is the best way to setup a tap interface on a cisco switch.

View 2 Replies View Related

Cisco Switching/Routing :: 6513 Span Session Limit?

Jul 12, 2012

I have a need to capture some traffic but my core 6513's are already using the limit of 2 span sessions. I can't edit any of the sessions either because I want to source traffic from vlans and you can only do one or the other. Is using a VACL with 'switchport capture' on the destination interface an option ? E.g. I want to source traffic from vlan 10,20,30,40 and send the all to interface Gi10/10 ? Is there any caveats ? I dont need to be too granular with the ACL's but just capture all traffic in those vlans.

View 2 Replies View Related

Cisco Switching/Routing :: How Many Span / Rspan Can Configure In Cat6500

Mar 16, 2011

i will be creating combination of SPAN and RSPAN on catalyst 6506 according to the link
 
[URL]
 
im planning to implement this on two 6506 switches will this work? or do i violate the number of monitor session? sorce span?
 
sw1
monitor session 1 source interface Fa5/18monitor session 1 destination interface Fa5/48
monitor session 2 source interface Fa6/34monitor session 2 destination interface

[Code].....

View 1 Replies View Related

Cisco Switching/Routing :: Nexus 7000 Span Limitation

Apr 18, 2012

I've learned recently that the Nexus 7000 only allows the configuration of a maximum of 2 Monitor sessions for spanning traffic. I only have one monitor session left and I need to do the following. 2 Core Nexus 7000 boxes with 2 different traffic probes/sniffers to each nexus( eg Sniffer 1 connects to Switch A on interface eth 1 and to Switch B on eth 1 ; Sniffer 2 connects to Switch A on eth 2 and to Switch B on eth 2.) My plan was to setup a standard session with multiple sources and destinations then on the interfaces connecting to the sniffers run a trunk and do 'sw trunk allowed xxxxx' and filter what I need to go to each sniffer box. However I've recently found out that some of my source traffic is coming from Port-Channel interfaces. Is there a way I can get around this and still do the filtering within only 1 monitor session ?

View 1 Replies View Related

Cisco Switching/Routing :: 4900 Span Configuration On Switches

Sep 16, 2012

i have configured SPAN on cisco 4900 series switches its a Loacal SPAN . as there is only commnads to complete this activity but hard luck its not working.

View 5 Replies View Related

Cisco Switching/Routing :: 3750 - SPAN Configuration For Websense

Jul 3, 2012

I have configured SPAN in cisco 3750 switch as below mentioned. but the destination port protocol is down.
 
Network Diagram:
 
switch(config)#monitor session 1 source interface gigabitethernet1/0/1switch(config)#monitor session 1 destination interface gigabitethernet1/0/11 ingress vlan 1

[Code]....

View 8 Replies View Related

Cisco Switching/Routing :: SPAN SIP And Wireshark 2950 Configuration

May 26, 2013

I have cisco 2651 with one L3 interface ip 172.26.18.200. This Cisco is gateway from E1 PRI (PBX Aastra MX-ONE TSW) to SIP (Asterisk). This cisco 2651 connected to cisco 2950 in port Fa 0/12. Fa 0/12 is in VLAN 518 (dot1q).

On cisco 2950 i made next commands:
 
# monitor session 1 source interface Fa 0/12 both encap dot1q
# monitor session 1 destination interface Fa 0/9
#sho monitor session 1
[Code].....

View 2 Replies View Related

Cisco Switching/Routing :: 6509 - Nexus And Span Sessions

Oct 24, 2011

I am in the early planning stages for a 6509 to Nexus 7K migration. Based on my experience with the 7K's at a previous company where we ran into a lot of issues, I am trying to be very careful.
 
I am more at home with the 6500 chassis and know what I can do with them.  I remember running into a limitation on the Nexus that involved their not supporting span sessions like the 6500's do.  Is that still the case ? 
 
If that isnt an option in the short term, I will need to look at a substantial investment in ethernet tap's to replace the lost span functionality because the security group's heavy use of span sessions.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved