Cisco Switching/Routing :: Remote Span With C2960
Mar 12, 2013
I am trying to configure RSPAN for one of my client. They have Server-Client VTP architecture. Voice Recording Server is connected to C4507. Agents are connected to C2960 and C3750. I got 2 sessions configured and the connectivity is a as follows:
1. Voice Recording Server-----C4507-----C2960-----C2960-----Agent IP Phones (Session 1)
2. Voice Recording Server-----C4507-----C3750-----Agent IP Phones (Session 2)
Recording works with Session-2 but not with Session-1. I understand the problem could be due to multiple reasons: 1.1. C2960 is working in client VTP mode so i cannot add remote span command under the vlan configuration. 1.2. C2960 has LANLITE IOS image which i am not sure if it supports Remote Span.
View 2 Replies
ADVERTISEMENT
Apr 8, 2012
I want to know what is the different between IOS of the catalyst WS-C2960-48PST-S and the IOS of catalyset WS-C2960-48PST-L.a want to upgrad the IOS of a WS-C2960-48PST-S with the IOS of WS-C2960-48PST-L (because this reference has a LANBASE version of IOS).
View 4 Replies
View Related
Dec 13, 2011
I am hoping you can provide me with some opinions, feedback, thoughts on the following. We have some Cisco 6509 switches in our environment currently hitting around 60% usage on the Router overall statistics.
Now we are looking at implementing an intrusion detection system but by being as least invasive as possible to the network. Our thoughts are to utilize a SPAN port on the switches to send traffic to the NIDS device but we have concerns of the following. The limitations of SPAN sessions on 6509's . The overhead on the switch of turning a SPAN session on and leaving it on permanently.
View 1 Replies
View Related
Dec 31, 2011
I have CISCO catalyst with VLANs (VLAN ID 33, 36, 40-53) configured. I need to configure port mirroring in Switch 3750 for NAC (Network Access Control). I need to Monitor all the VLANs. Here is the SPAN configuration of switch: [code] Monitor session 1 source vlan 33 , 36 , 40 – 53.Monitor Session 1 destination interface fa 1/0/8 (here I am not able to set encapsulation dot1q ) because the error occurred saying %one or more dest port do not support the encapsulation%.
View 5 Replies
View Related
Feb 12, 2013
I currently have IOS image cat4500e-entservices-mz.122-53.SG5.bin. According to my research it appears SPAN is supported on this OS. However, after looking at procedure notes using websites like here:
[url]... I cannot find and obviously not figure out how to use the SPAN command. My main objective is to simply setup a port mirror on one of my TenGigabitEthnet interfaces and from what I read SPAN is the best way to setup a tap interface on a cisco switch.
View 2 Replies
View Related
Dec 12, 2011
Been dealing with a strange problem for several days now. It started out with a problem that I thought was VTP related but ended up being something else. I setup a span port on a 3750 that I am connected to that was mirroring the trunk connection coming into the switch.
Never saw an VTP traffic come across the connection but doing a sh vtp status indicated the traffic was arriving and getting processed. When I found some debug commands (debug sw-lan vtp), I was also able to see the packets go between switches. Seeing this issue concerns me that there is other traffic that isnt showing up during a span session.
I know that doing a span on a switch, especially using a trunk port as a source, isnt a good idea. Since I didnt have a TAP at time, this was my only choice. I have since borrowed a NetOptics TP-CU3 tap from a good friend and was able to confirm the VTP traffic was going across the trunk connection between switches.
All of my 3750's are running 12.2.55.SE.
View 8 Replies
View Related
May 1, 2013
I have a Cisco 881 router running 15.1(4)M4. I am trying to configure SPAN on it to mirror my outside interface (source) to one of my LAN interfaces (dest).
!--- WAN interface
interface FastEthernet4
description Comcast WAN$ETH-WAN$
[Code]......
As you can see from the above output there is a problem with the command on this interface. When I try to set Fa0 as my source it works fine:
rtr(config)#mon session 1 source int fastEthernet 0
rtr(config)#
Is this because fa4 is layer 3 and fa0 is a switchport? If so, is there another way to set fa4 as the source?
View 4 Replies
View Related
Jul 12, 2012
I have a need to capture some traffic but my core 6513's are already using the limit of 2 span sessions. I can't edit any of the sessions either because I want to source traffic from vlans and you can only do one or the other. Is using a VACL with 'switchport capture' on the destination interface an option ? E.g. I want to source traffic from vlan 10,20,30,40 and send the all to interface Gi10/10 ? Is there any caveats ? I dont need to be too granular with the ACL's but just capture all traffic in those vlans.
View 2 Replies
View Related
Mar 16, 2011
i will be creating combination of SPAN and RSPAN on catalyst 6506 according to the link
[URL]
im planning to implement this on two 6506 switches will this work? or do i violate the number of monitor session? sorce span?
sw1
monitor session 1 source interface Fa5/18monitor session 1 destination interface Fa5/48
monitor session 2 source interface Fa6/34monitor session 2 destination interface
[Code].....
View 1 Replies
View Related
Apr 18, 2012
I've learned recently that the Nexus 7000 only allows the configuration of a maximum of 2 Monitor sessions for spanning traffic. I only have one monitor session left and I need to do the following. 2 Core Nexus 7000 boxes with 2 different traffic probes/sniffers to each nexus( eg Sniffer 1 connects to Switch A on interface eth 1 and to Switch B on eth 1 ; Sniffer 2 connects to Switch A on eth 2 and to Switch B on eth 2.) My plan was to setup a standard session with multiple sources and destinations then on the interfaces connecting to the sniffers run a trunk and do 'sw trunk allowed xxxxx' and filter what I need to go to each sniffer box. However I've recently found out that some of my source traffic is coming from Port-Channel interfaces. Is there a way I can get around this and still do the filtering within only 1 monitor session ?
View 1 Replies
View Related
Sep 16, 2012
i have configured SPAN on cisco 4900 series switches its a Loacal SPAN . as there is only commnads to complete this activity but hard luck its not working.
View 5 Replies
View Related
Jul 3, 2012
I have configured SPAN in cisco 3750 switch as below mentioned. but the destination port protocol is down.
Network Diagram:
switch(config)#monitor session 1 source interface gigabitethernet1/0/1switch(config)#monitor session 1 destination interface gigabitethernet1/0/11 ingress vlan 1
[Code]....
View 8 Replies
View Related
May 26, 2013
I have cisco 2651 with one L3 interface ip 172.26.18.200. This Cisco is gateway from E1 PRI (PBX Aastra MX-ONE TSW) to SIP (Asterisk). This cisco 2651 connected to cisco 2950 in port Fa 0/12. Fa 0/12 is in VLAN 518 (dot1q).
On cisco 2950 i made next commands:
# monitor session 1 source interface Fa 0/12 both encap dot1q
# monitor session 1 destination interface Fa 0/9
#sho monitor session 1
[Code].....
View 2 Replies
View Related
Oct 24, 2011
I am in the early planning stages for a 6509 to Nexus 7K migration. Based on my experience with the 7K's at a previous company where we ran into a lot of issues, I am trying to be very careful.
I am more at home with the 6500 chassis and know what I can do with them. I remember running into a limitation on the Nexus that involved their not supporting span sessions like the 6500's do. Is that still the case ?
If that isnt an option in the short term, I will need to look at a substantial investment in ethernet tap's to replace the lost span functionality because the security group's heavy use of span sessions.
View 1 Replies
View Related
May 23, 2012
I'm trying to configure a mirror port on a 3750. This configuration needs to replicate data from local ports, but I need that also act as a regular access port.
With the initial configuration, SPAN port, there is no problem, all the data of the configurated ports is replicating in the configurated port. On the port configurated as mirror there is a PC connected for audio recording. When the port is not operating as SPAN there is communications without problem over the LAN. But when I configure the port as SPAN, communication is interrupted.
Here is the actual configuration:
SWITCH1-PISO7#sh monitor session 1
Session 1
---------
Type : Local Session
[Code]......
View 5 Replies
View Related
Dec 26, 2012
We have a customer who uses about 20 x c2960's switches for access layer and 2 x c3560e for distribution layer. C2960's uses C2960-LANLITEK9-M , Version 12.2(58)SE1. Everything was working fine. Now we got information, that sometimes there are problems with connectivity. Customer tries to reach internet.
SW11#sh int fa0/18
FastEthernet0/18 is up, line protocol is up (connected)
Hardware is Fast Ethernet, address is e8ba.806a.4412 (bia e8ba.806a.4412)
[Code].....
View 7 Replies
View Related
Jan 29, 2012
I am having problem in upgrading Cat2960 because I deleted the flash in this switch already and now I need installing an IOS image? [code]
View 1 Replies
View Related
Dec 30, 2009
I do not see 802.1Q tags nor do I see p-bits (COS) in my wireshark captures. My setup is not working and I have no way to verify (sniff) that the 6509 is setting the p-bits to 3. [code]
View 4 Replies
View Related
Jun 8, 2012
i have configured SPAN over cisco 2960 to monitor source port traffic but after configuration i dont able to get response from destination port as my NMS is attached on destination port so i lost its web interface.
Configuration is as under.
monitor session 1 source interface gigabitEthernet0/5 (Source Port on Vlan 100) monitor session 1 destination interface gigabitEthernet0/1 (Destination Port on Vlan 200)
View 2 Replies
View Related
May 18, 2013
I have a single Nexus 7K (6.x) with only F2 modules and I would like to SPAN the same source interfaces and vlans to mulitple destination servers (interfaces). When configuring SPAN to a single destination traffic gets replicated successfully but when I add an additional destination to the same SPAN session then none of the destination interfaces receive any traffic. As soon as modify the SPAN to include only a single destination interface it works again. I'm guess this is a limitation of the Nexus 7K 6.x code or the F2 modules.
View 4 Replies
View Related
Jun 9, 2013
I'm setting up a montitor session on a NEXUS 7K as below.we are receiving in 150M of data and 0 data going out port 9/25.but port 4/24 shows 300M to the span port?
View 1 Replies
View Related
Oct 1, 2012
i am running c3640-is-mz.124-21.bin on a cisco router 3640. i am trying to create a monitor session in the CLI and everytime i type the command Router(config)#monitor session 1 interface ethernet2/1 % Invalid input detected at '^' marker. Router(config)#monitor session 1 interface ethernet2/1 ^% Invalid input detected at '^' marker. i get the error invalid input ?
View 10 Replies
View Related
Dec 12, 2012
I'm trying to configure a SPAN session on a Cisco 3725 router, but it won't let me complete the command. The router has two Fast Ethernet interfaces: 0/0 and 0/1. I'm trying to configure a SPAN session with Fa0/0 as the source interface and Fa0/1 as the destination interface. [code] But when I try to configure the session, it seems like it's giving me the option to configure the SPAN session, but in the end the router won't let me: [code] When I type "?", why would it give me the option of using the Fast Ethernet interface as source port, then when I try to execute the command, it doesn't like it?
View 7 Replies
View Related
Mar 2, 2012
I have two servers, connected on two(Different) 6513 directly connected switches. Both these servers are in the same Vlan.
I have to monitor communication these two servers. I have a system connected on one of the 6513 switch, where network tool wireshark is installed.
How to configure span port.
switch 6513-1# show run int Gi10/43 --------------------Server 1 is connected
switch 6513-2# show run int Gi9/45 ------------------------Server 2 is connected
switch 6513-2# show run int Gi9/46 ------------------------System on which network tool wireshark is installed.
View 9 Replies
View Related
Mar 3, 2013
rsbd7k01-p-vdca(config)# monitor session 2
rsbd7k01-p-vdca(config-monitor)# source vlan ?
<1-3967>
rsbd7k01-p-vdca(config-monitor)# source vlan 1 - 3967
ERROR: vlan 33-3967: Number of source vlans exceeds maximum
rsbd7k01-p-vdca(config-monitor)#
View 3 Replies
View Related
Mar 22, 2012
I have configured Span port on our 4510. We have an application 5view server to monitor trafic connected to G9/17 Since we have changed the network connection from physical Giga port and add a Port-channel instead, we don't see any more trafic from the new Port-channel to G9/17
We have the configuration below on our 4510 :
monitor session 1 source interface Gi4/6
monitor session 1 source interface Po20
monitor session 1 filter vlan 311 - 312 , 375
monitor session 1 destination interface Gi9/17
From the commands show, we don't see the trafic duplication from the source to the destination port :
Port Source
4510-5567#sh int po20
Port-channel20 is up, line protocol is up (connected)
Hardware is EtherChannel, address is 0016.9de2.a818 (bia 0016.9de2.a818)
[Code].....
View 2 Replies
View Related
Apr 23, 2013
I have a C2960-24TT-L Switch with the following problem:When the Power Cord is plugged in the Switch, all switch indicator LEDs go on very briefly. Then SYST LED blinks very briefly, goes on steady and remains at this state without any indication at the console.Tried the reset by holding the MODE button while plugging in power but I still get no indication at the console. All is fine with console, meaning that if I take out the cable and plug it in another switch, then I see all that there is there to be seen.My question: Is the switch beyond repair or is there something that can be done to get the switch to run POST and boot at rommon so that I can reload SW and configs?
View 3 Replies
View Related
Apr 26, 2012
I have two WS-C2960-24TC-L Switch with Software Ver 12.2(25r)SEE6 with image c2960-lanbase-mz.122-35.SE5.bin and 12.2(25r)SEE1 with image c2960-lanbase-mz.122-25.SEE2.bin currently on it.
I want to enable SSH connections on the switches and believe I need to import the cryto image onto the switch. I would like to upgrade it to new version that can also support ssh connection but not sure which image to download from cisco. The switches are now live.
System image file is "flash:c2960-lanbase-mz.122-35.SE5/c2960-lanbase-mz.122-35.SE5.bin"
cisco WS-C2960-24TC-L (PowerPC405) processor (revision H0) with 61440K/4088K
[Code].....
View 5 Replies
View Related
Feb 7, 2012
I've got a C2960 (sw01) and a C2948. (sw02) The sw02 switch is trunked with sw01, and is meant to serve as an extension to the VLANs (1-4) that exist on sw01. It is trunking properly, however, how would I go about giving the sw02 an IP so that I can access it via SSH? Would I have to create a VLAN specifically on sw02 with an ip and switchport an interface to use it? I know that a VLAN can only have a single IP, but I'd like sw02 to have an IP on VLAN1 (192.168.1.0 subnet), is that possible?
View 5 Replies
View Related
Feb 14, 2012
i am trying to upgrade the firmware in my C2960 switch to 15(1) SE2, and i get the error:Failed to execute the command archive download -sw /overwrite /http iosFile
View 2 Replies
View Related
Jul 1, 2012
I am not sure why the CRC and input errors are increasing in fastethernet port...This port is used as Intradomain cross connect to Data Center service provider for LAN extension between two Data Centers in different locations... The link is 100 MB. The switch port is directly connected to patch panel of DC provider and I believe they have some L3 switch or some other device that is providing LAN extension...
#sh interfaces fastEthernet 0/23
FastEthernet0/23 is up, line protocol is up (connected)
Hardware is Fast Ethernet, address is 0019.3050.1497 (bia 0019.3050.1497)
Description: ASA_VPN_TO
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
[code]....
View 26 Replies
View Related
Oct 2, 2012
I am not sure why the CRC and input errors are increasing in fastethernet port...This port is used as Intradomain cross connect to Data Center service provider for LAN extension between two Data Centers in different locations... The link is 100 MB. The switch port is directly connected to patch panel of DC provider and I believe they have some L3 switch or some other device that is providing LAN extension...
#sh interfaces fastEthernet 0/23
FastEthernet0/23 is up, line protocol is up (connected)
Hardware is Fast Ethernet, address is 0019.3050.1497 (bia 0019.3050.1497)
[Code].....
View 3 Replies
View Related
May 19, 2013
I have an issue with one of our switches, switch model WS-C2960-24TC-L, i am not able to display switch temperature as below,
Switch#sh verCisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 15.0(2)SE2, RELEASE SOFTWARE (fc1)Technical Support: URL ) 1986-2013 by Cisco Systems, Inc.Compiled Tue 05-Feb-13 12:41 by prod_rel_team(code)
View 2 Replies
View Related
