Cisco Switching/Routing :: 2960 -Destination Port Not Responding Over SPAN
Jun 8, 2012
i have configured SPAN over cisco 2960 to monitor source port traffic but after configuration i dont able to get response from destination port as my NMS is attached on destination port so i lost its web interface.
Configuration is as under.
monitor session 1 source interface gigabitEthernet0/5 (Source Port on Vlan 100) monitor session 1 destination interface gigabitEthernet0/1 (Destination Port on Vlan 200)
View 2 Replies
ADVERTISEMENT
Jan 16, 2012
In s SPAN session , normally the destination prt is used for monitoring purpose only. But could destination port be used to access the equipement or PC connected to that port , for a 2960 LAN BASE image switch .
View 2 Replies
View Related
Dec 12, 2011
Been dealing with a strange problem for several days now. It started out with a problem that I thought was VTP related but ended up being something else. I setup a span port on a 3750 that I am connected to that was mirroring the trunk connection coming into the switch.
Never saw an VTP traffic come across the connection but doing a sh vtp status indicated the traffic was arriving and getting processed. When I found some debug commands (debug sw-lan vtp), I was also able to see the packets go between switches. Seeing this issue concerns me that there is other traffic that isnt showing up during a span session.
I know that doing a span on a switch, especially using a trunk port as a source, isnt a good idea. Since I didnt have a TAP at time, this was my only choice. I have since borrowed a NetOptics TP-CU3 tap from a good friend and was able to confirm the VTP traffic was going across the trunk connection between switches.
All of my 3750's are running 12.2.55.SE.
View 8 Replies
View Related
May 23, 2012
I'm trying to configure a mirror port on a 3750. This configuration needs to replicate data from local ports, but I need that also act as a regular access port.
With the initial configuration, SPAN port, there is no problem, all the data of the configurated ports is replicating in the configurated port. On the port configurated as mirror there is a PC connected for audio recording. When the port is not operating as SPAN there is communications without problem over the LAN. But when I configure the port as SPAN, communication is interrupted.
Here is the actual configuration:
SWITCH1-PISO7#sh monitor session 1
Session 1
---------
Type : Local Session
[Code]......
View 5 Replies
View Related
Jun 9, 2013
I'm setting up a montitor session on a NEXUS 7K as below.we are receiving in 150M of data and 0 data going out port 9/25.but port 4/24 shows 300M to the span port?
View 1 Replies
View Related
Oct 1, 2012
i am running c3640-is-mz.124-21.bin on a cisco router 3640. i am trying to create a monitor session in the CLI and everytime i type the command Router(config)#monitor session 1 interface ethernet2/1 % Invalid input detected at '^' marker. Router(config)#monitor session 1 interface ethernet2/1 ^% Invalid input detected at '^' marker. i get the error invalid input ?
View 10 Replies
View Related
Mar 2, 2012
I have two servers, connected on two(Different) 6513 directly connected switches. Both these servers are in the same Vlan.
I have to monitor communication these two servers. I have a system connected on one of the 6513 switch, where network tool wireshark is installed.
How to configure span port.
switch 6513-1# show run int Gi10/43 --------------------Server 1 is connected
switch 6513-2# show run int Gi9/45 ------------------------Server 2 is connected
switch 6513-2# show run int Gi9/46 ------------------------System on which network tool wireshark is installed.
View 9 Replies
View Related
Oct 29, 2011
I read quite a few documents on configuring SPAN on a cisco switch but none of them mention any limitations or any kind of CPU load it can have on a switch. I need to configure this on one of our switches and would like to know if there are any implications related to SPAN.
View 5 Replies
View Related
Jun 18, 2012
I have configured SPAN in cisco 3750 switch as below mentioned. but the destination port protocol is down.switch(config)#monitor session 1 source interface gigabitethernet1/0/1switch(config)#monitor session 1 destination interface gigabitethernet1/0/11 ingress vlan 1
View 8 Replies
View Related
Apr 17, 2013
If I monitor a trunkport on the rootbridge in both directions I get Duplicate Multicast Packets on the perticular VLAN. The first guess is, that this is worked as designed and not a IOS Bug (Platform CAT6500 SUP720 IOS 12.2(33)SXI9 ) Until know I only found an old Cisco press link from 2002 with this subject.
View 2 Replies
View Related
Nov 2, 2011
Is it possible to configure the span(switch port analyzer) port and restrict it to only listen to ingress and egress of TCP/1433 from the source port?
View 2 Replies
View Related
May 19, 2013
Basically I am trying to use Wireshark to do a packet capture on a Nexus 5010. I want to do a monitor session on on the switch so I can capture from a source port to a destination port on the same switch. I can configure the source port but when I go to configure the destination port I get "ERROR: Eth102/1/4: Configuration not allowed on fex interface". I have tried to reconfigure this port as a switchport but "switchport mode access" command does not take. I don't want to make any changes to any other ports but this one.
View 1 Replies
View Related
Apr 4, 2011
I am having some problems creating a SPAN port on my Cisco 871 (running IOS 12.4-11T). My 871 is connected to a DSL modem, and uses "IP Negotiated" to get its dynamic ip address.I want to monitor the WAN port (FastEthernet4) using SPAN, but when I type "monitor session 1 source interface FastEthernet4" into the cli, it is rejected. I can successfully use any of the other FastEthernet ports, as well as Vlan1 as a source for the SPAN session. I have tried to use Dialer0 instead of FastEthernet4, but it still doesnt work.
View 5 Replies
View Related
Mar 18, 2013
I have Catalyst 2960 S (WS-C2960S-48FPS-L) Switch. I have plugged in SFP module but still interface is down and line protocol down. Is there any configuration to enable SFP module and make the interface up?
This port is connected to nexus 5 k.
View 11 Replies
View Related
Mar 5, 2012
I have a Cisco 2960 48-port switch. I enter "sh vlan" and it lists all the VLAN's. One of the VLAN's listed is "10" with the name "EPIC". What is the quickest way to find out what ports, if any, are assigned to this VLAN?
View 2 Replies
View Related
Aug 29, 2012
Our company bought a Cisco 2960-S to add to the network, We gave the interface VLAN 1 an IP address, and tried to attached the switch to a jack port on the wall to test if it gets a link or not. The status of the port blinks amber and stays contionous amber, I have searched the manual of the switch and it says that amber means that the port is being blocked by STP.
View 4 Replies
View Related
Mar 2, 2012
If I knew the IP address of a host, can we know on which port on the switch its connected. The switch model is 2960
View 6 Replies
View Related
Nov 5, 2009
To rate limit the 2960 switch port to 1 MB.I have made the specified chnages , how ever still it is reaching more tha 1 MB
Hard coded the bandwidth of port to 10 MB and have applied the specified command srr-queue bandwidth limit 10.
View 4 Replies
View Related
Dec 15, 2009
One of my engineers issued a command to turn off port security on a number of ports using the range command. The command failed on the first attempt due to a tacacs auth failure which I suspect is due to a low tacacs timeout value. The engineer then reduced the number of ports in the range command and re-issued the config change after which the switch just crashed and rebooted.
The logging buffer on the switch displays the following:
000072: *Mar 1 00:03:00 GMT: %PLATFORM-1-CRASHED: System previously crashed with the following message:
000073: *Mar 1 00:03:00 GMT: %PLATFORM-1-CRASHED: Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 12.2(50)SE3, RELEASE SOFTWARE (fc1)
000074: *Mar 1 00:03:00 GMT: %PLATFORM-1-CRASHED: Technical Support: [URL]
000075: *Mar 1 00:03:00 GMT: %PLATFORM-1-CRASHED: Copyright (c) 1986-2009 by Cisco Systems, Inc.
000076: *Mar 1 00:03:00 GMT: %PLATFORM-1-CRASHED: Compiled Wed 22-Jul-09 07:03 by prod_rel_team
000077: *Mar 1 00:03:00 GMT: %PLATFORM-1-CRASHED:
[Code]........
I have done some searching and this could be related to bug CSCsq71492. I have tried using the output interpreter but it is still down.
View 22 Replies
View Related
Mar 1, 2010
I have upgraded a couple of 2960G switches to 12.2.52SE and now discovered that TCP port 4786 is open on the switches.
I have looked in the document{URL}, trying to find a way to disable this function/port, but didn't find anything useful. Any way to disable this function/port?
View 3 Replies
View Related
Oct 22, 2011
I have a couple of Cisco 2960's sending syslog messages to a remote syslog-ng on port 514 (standard).
I need to set another Swtich so it sends traffic to the same syslog server but on another UDP port (such as 714),, is that possible,? I cannot find the option on the documentation.
View 9 Replies
View Related
Jul 30, 2012
I am configuring a Cat 2960 port for connecting a VOIP phone, authenticated by MAB. On connecting the phone, I get the port authenticated and assigned to the correct VLAN, with LLDP-MED advertising the correct voice vlan. However, I then see no traffic from the phone on the switch. I can see the MAC address of the phone is learned in the right VLANs, but the mac address is showing as "Drop", which normally means the address is statically configured to be blocked. There is no static mac address table blocking configured on the switch.
Switch Version
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 50 WS-C2960-48TC-L 15.0(1)SE3 C2960-LANBASEK9-M
Port configuration
interface FastEthernet0/1
description "Standard user port"
[code].....
View 1 Replies
View Related
Jan 3, 2012
I want to implement port-based and MAC-based in these two switches: 2960 & 3560 (both of them have this IOS version: 12.2(55)SE1). And I haven't found a way to implement both of them at the same time. This is what I got:
ip dhcp use subscriber-id client-id
ip dhcp subscriber-id interface-name
ip dhcp excluded-address 192.168.0.0 192.168.0.2
ip dhcp excluded-address 192.168.0.251 192.168.0.255
[code]....
With this configuration I can use port-based, but not MAC based. If I remove the first two lines and change the last line for this one:
address 192.168.0.7 client-id 0112.ae1d.af58.60
Then, the computer with that MAC address got the correct IP, but then the port-based doesn't work. Also, I got this line in the interface what I want to use MAC-based:
ip dhcp server use subscriber-id client-id
View 3 Replies
View Related
Mar 10, 2013
I am planning on deploying a 2960 switch and will need to uplink it to a 4510 switch. There are 2 TenGig Ports available and I was thinking of uplinking one of them to the 1Gb SFP port on the 2960. Would this work?
View 4 Replies
View Related
May 21, 2012
We're going to be switching some of our gear from Foundry to Cisco, and were looking at the WS-C2960S-48TS-L. We currently have 3 different VLAN's, and I wanted to have 1 uplink back to our firewall (ASA 5550) and then let the firewall do the routing between the subnets. I realize that 1 link will carry the traffic twice then, but is that possibly with those switches to have all three vlans assigned to one port and then just let the firewall do the routing between the vlans or would I need to have 3 uplink ports back to the 5550?
View 1 Replies
View Related
Jan 25, 2012
I am testing 2960 24 S with storm-control and Errdisable Port timer interval 60s , connected HUB on fa0/17 to make traffic / loop.After Strom Control detection the interface goes down thats ok after 60s they will try to recover the interface and going up although the loop is still there.For my understanding if the interface detect still a loop on that interface they will disable the port again for 60s and will check again. [code]
View 7 Replies
View Related
Feb 18, 2013
I configured port security on my 2960 switches with the following commands: [code]
The problem is that when I should change someone's PC, first I disable port-secirity, then I clear all the mac addresses learned on the interface, then I plug the new PC and enable port-security. The new PC couldn't connect to the network and it's mac address has not be learned on the interface. Why?Which commands should I use to clear an old mac address and enable port-security with the new mac address.
View 4 Replies
View Related
Dec 18, 2011
i want use CACTI for monitor my bandwidth so i have a question how can i enable snmp for a switch port ? or i shoudl just enable snmp from configuratiopn terminal and then in CACTI i will choose which port will be monitor? can i do something that CACTI connect to my switch with a encryption key ? i have cisco 2960 48 port switch
View 2 Replies
View Related
Aug 16, 2012
In my network we use all cisco 2960 switches, problem is when someone copying 4gb data or high from one switch to another switch, by that time rto (Request time out) is coming.
router
|
|
|
[Code]....
1. when user 1 copy data from server ,at that time who is in switch2 behind like user2 ,he is getting problem like when ping to default-gateway,or rto is coming and network is very slow .
2. when i open sw2,sw1,sw3,trunk ports utilization is very high except sw4 to sw1 trunk ports,who behind sw4 like user4 ,he is not getting problem.
3.all switches trunkport in my network is faster ethernet and i have no option to connect trunkport to gigaehternet and ethernet channel.
View 2 Replies
View Related
Aug 15, 2012
I am experiencing the same problem described in this post {URL}. I have seen this happen on different networks, with different equipment attached. It happens on both 2960 and 3750 switches. Basically the connection drops, and we see in the web interface "Port is Disabled". This appears to happen every 10 minutes.
On the CLI, the status shows as connected.
Port Name Status V lan Duplex Speed Type
Fa0/38 connected 1 a-full a-100 10/100BaseTX
I have ran cable diagnostics while the drop out is occurring.
Interface Speed Local pair Pair length Remote pair Pair status
--------- ----- ---------- ----------------- ----------- -------------------
Fa0/38 100M Pair A 28 +/- 15 meters Pair B Normal
[code]...
During the outage, I see the duplex fluctuate between full and half. The outage occurs for approx 90 seconds. If I fix the duplex and speed at both ends, the outage reduces to around 30 seconds. If I apply spanning-tree port fast the outage reduces further to around 10 seconds. Before I change any configuration on the port, the logs show the interface going down
Aug 16 13:06:51.875: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/38, changed state to down
Aug 16 13:06:52.874: %LINK-3-UPDOWN: Interface FastEthernet0/38, changed state to down
[code]...
However, once I apply the configuration nothing is logged. However we can still see the connection is disappearing for around 10 seconds. I suspect the issue wasn't resolved for the person reporting the problem in the link above, but because the outage is minimized, and not being logged it is going unnoticed.
View 30 Replies
View Related
Jan 21, 2013
Is there a way to identify if a switch port is burned via CLI? I have a 2960-48PST switch and some ports don't provide power to a PoE device connected. When I change the port, the device turns on.
View 3 Replies
View Related
Sep 18, 2012
I want to configure switch port bandwidth limit for my Catalyst 2960-48, is there any hardware / ios limitation? can I configure it at all 48 switch ports?
View 1 Replies
View Related
Apr 4, 2012
how can i limit bandwidth on a gig port of 2960 or 4506e switch?
View 9 Replies
View Related
