I am planning on deploying a 2960 switch and will need to uplink it to a 4510 switch. There are 2 TenGig Ports available and I was thinking of uplinking one of them to the 1Gb SFP port on the 2960. Would this work?
View 4 RepliesI have cisco 2960 and Catlyst 4510 switches now we are planning to implement IPV6.
i have the fallowing IOS on my switches.
C2960-lanbasek9-mz.122-50.se5
Cat4500e-entservicesk9-mz.122-54.sg1.bin
The above ios will support for IPV6 or I have to purchase new IOS, which version will support.
I am looking to find a command or counter to tell me if a cisco switch port on a 4510 was ever up and passed traffic. I want to shutdown all unused switchports on our access switches. But before I do that I need to make sure device is just not off or the person is away on vacation. If I do sh int interface, is there a counter I can reference.
View 4 Replies View RelatedAre you only able to have two sessions for port mirroring on a Cisco 4510?
View 1 Replies View RelatedWe currently have Cisco WS-X6708-10GE blade installed in our Cisco 7606-S switch. Each of the ports have a X2-10GB-SR tranciever. When I look at the port with the "sh int tengig xx" command I see the following:
!
TenGigabitEthernet 4/1 is up, line protocol is up (connected)
Hardware is c7600 10Gb 802.3, address is 001c.b0ca.75c0
!
TenGigabitEthernet 4/2 is up, line protocol is up (connected)
Hardware is c7600 10Gb 802.3, address is 001c..b0ca.75c0(code)
I have packet loss with QoS configured and I was wondering is it somehow connected with the QoS configured on the switch.The traffic is passing through fa0/19 and gi0/1 interfaces.
mls qos map cos-dscp 0 8 16 24 32 46 48 56
mls qos srr-queue input bandwidth 90 10
mls qos srr-queue input threshold 1 8 16
mls qos srr-queue input threshold 2 34 66
[code]...
When i connect two cisco 2960 series switchs via stright trough cable causes delay in transmission sw1 has vlans and having trunk port connected to router all vlans are able to access internet sw2 is connected to vlan5 on switch1 sw2 has factory default configuration computers on sw2 can access internet but I have low bandwith problem on sw2 there is transmission delay problem?
View 1 Replies View RelatedI need to connect 4 Floor Building with 4 Cisco 2960 - 48 ports switch each other and it needs to be through a fiber. So all PCs connected to each switch would reach the LAN/WAN from the other switch. (attached is the image here with)
I see that the 2960 has 2 SFP ports each port of each switch should connect each other or how?
My simple question is:
1. What cable / patch code I have to use = Single-mode or Multimode? ( distance for each switch will not more then 25 mts)
2. Do I have to use SFP or SFP+ module?
3. What kind of SFP/SFP+ module I have to use = Single-mode or Multimode?
4. What kind of connector should patch code have = LC / SC or ?
5. How to connect each switch with redundancy like ...each switch should be interconnected with each other or I have to choose Cisco 3750G which has more then 2 SFP ports (option#1 & opetion#2 = attached here with) =
Best practice for connecting cisco switches over fiber.
I have two Catalyst 2960 Series (48 port) switches with the newest Cisco IOS installed. There is also a Cisco 2600 Series Router which I can't manage because it's ISP managed.
Now the problem is as follows. I'd like to create two VLANs, one in the IP range 192.168.0.xxx and the other in the 192.168.1.xxx. Now the router has a gateway IP address 192.168.1.1 .
Would it be possible to somehow connect these two VLANs with the router so that these 2 VLANs can't see each other but they can ofcourse both contact the router and exit on the internet?
I was looking for a way to connect an AUX port from a 1700 router to a 6500 switch module console port, to see the output of the Switch's on the 1700 router, in case there is a network downtime, I could see what's going on in the switch, what cable should I use ? Also, is there is any kind of documentation for this type of config what have I seen is very few info.
View 2 Replies View RelatedI have Catalyst 2960 S (WS-C2960S-48FPS-L) Switch. I have plugged in SFP module but still interface is down and line protocol down. Is there any configuration to enable SFP module and make the interface up?
This port is connected to nexus 5 k.
I have a Cisco 2960 48-port switch. I enter "sh vlan" and it lists all the VLAN's. One of the VLAN's listed is "10" with the name "EPIC". What is the quickest way to find out what ports, if any, are assigned to this VLAN?
View 2 Replies View RelatedOur company bought a Cisco 2960-S to add to the network, We gave the interface VLAN 1 an IP address, and tried to attached the switch to a jack port on the wall to test if it gets a link or not. The status of the port blinks amber and stays contionous amber, I have searched the manual of the switch and it says that amber means that the port is being blocked by STP.
View 4 Replies View RelatedI have a Cisco Catalyst 2960 series switch. When I connect another switch or a VMWare Esx server on one of the ports, the port blinks for few seconds and then goes off. When I connect a desktop or laptop or a windows server the ports stay led and I can access resources on the network. However, when connect another switch or a vmware esx server, the port is disabled.
What config in the switch can I check to make sure the ports stay on regardless when I connect a desktop / laptop, switch or vmware server?
If I knew the IP address of a host, can we know on which port on the switch its connected. The switch model is 2960
View 6 Replies View RelatedTo rate limit the 2960 switch port to 1 MB.I have made the specified chnages , how ever still it is reaching more tha 1 MB
Hard coded the bandwidth of port to 10 MB and have applied the specified command srr-queue bandwidth limit 10.
One of my engineers issued a command to turn off port security on a number of ports using the range command. The command failed on the first attempt due to a tacacs auth failure which I suspect is due to a low tacacs timeout value. The engineer then reduced the number of ports in the range command and re-issued the config change after which the switch just crashed and rebooted.
The logging buffer on the switch displays the following:
000072: *Mar 1 00:03:00 GMT: %PLATFORM-1-CRASHED: System previously crashed with the following message:
000073: *Mar 1 00:03:00 GMT: %PLATFORM-1-CRASHED: Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 12.2(50)SE3, RELEASE SOFTWARE (fc1)
000074: *Mar 1 00:03:00 GMT: %PLATFORM-1-CRASHED: Technical Support: [URL]
000075: *Mar 1 00:03:00 GMT: %PLATFORM-1-CRASHED: Copyright (c) 1986-2009 by Cisco Systems, Inc.
000076: *Mar 1 00:03:00 GMT: %PLATFORM-1-CRASHED: Compiled Wed 22-Jul-09 07:03 by prod_rel_team
000077: *Mar 1 00:03:00 GMT: %PLATFORM-1-CRASHED:
[Code]........
I have done some searching and this could be related to bug CSCsq71492. I have tried using the output interpreter but it is still down.
I have upgraded a couple of 2960G switches to 12.2.52SE and now discovered that TCP port 4786 is open on the switches.
I have looked in the document{URL}, trying to find a way to disable this function/port, but didn't find anything useful. Any way to disable this function/port?
I have a couple of Cisco 2960's sending syslog messages to a remote syslog-ng on port 514 (standard).
I need to set another Swtich so it sends traffic to the same syslog server but on another UDP port (such as 714),, is that possible,? I cannot find the option on the documentation.
I am configuring a Cat 2960 port for connecting a VOIP phone, authenticated by MAB. On connecting the phone, I get the port authenticated and assigned to the correct VLAN, with LLDP-MED advertising the correct voice vlan. However, I then see no traffic from the phone on the switch. I can see the MAC address of the phone is learned in the right VLANs, but the mac address is showing as "Drop", which normally means the address is statically configured to be blocked. There is no static mac address table blocking configured on the switch.
Switch Version
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 50 WS-C2960-48TC-L 15.0(1)SE3 C2960-LANBASEK9-M
Port configuration
interface FastEthernet0/1
description "Standard user port"
[code].....
I want to implement port-based and MAC-based in these two switches: 2960 & 3560 (both of them have this IOS version: 12.2(55)SE1). And I haven't found a way to implement both of them at the same time. This is what I got:
ip dhcp use subscriber-id client-id
ip dhcp subscriber-id interface-name
ip dhcp excluded-address 192.168.0.0 192.168.0.2
ip dhcp excluded-address 192.168.0.251 192.168.0.255
[code]....
With this configuration I can use port-based, but not MAC based. If I remove the first two lines and change the last line for this one:
address 192.168.0.7 client-id 0112.ae1d.af58.60
Then, the computer with that MAC address got the correct IP, but then the port-based doesn't work. Also, I got this line in the interface what I want to use MAC-based:
ip dhcp server use subscriber-id client-id
i have configured SPAN over cisco 2960 to monitor source port traffic but after configuration i dont able to get response from destination port as my NMS is attached on destination port so i lost its web interface.
Configuration is as under.
monitor session 1 source interface gigabitEthernet0/5 (Source Port on Vlan 100) monitor session 1 destination interface gigabitEthernet0/1 (Destination Port on Vlan 200)
We're going to be switching some of our gear from Foundry to Cisco, and were looking at the WS-C2960S-48TS-L. We currently have 3 different VLAN's, and I wanted to have 1 uplink back to our firewall (ASA 5550) and then let the firewall do the routing between the subnets. I realize that 1 link will carry the traffic twice then, but is that possibly with those switches to have all three vlans assigned to one port and then just let the firewall do the routing between the vlans or would I need to have 3 uplink ports back to the 5550?
View 1 Replies View RelatedI am testing 2960 24 S with storm-control and Errdisable Port timer interval 60s , connected HUB on fa0/17 to make traffic / loop.After Strom Control detection the interface goes down thats ok after 60s they will try to recover the interface and going up although the loop is still there.For my understanding if the interface detect still a loop on that interface they will disable the port again for 60s and will check again. [code]
View 7 Replies View RelatedI configured port security on my 2960 switches with the following commands: [code]
The problem is that when I should change someone's PC, first I disable port-secirity, then I clear all the mac addresses learned on the interface, then I plug the new PC and enable port-security. The new PC couldn't connect to the network and it's mac address has not be learned on the interface. Why?Which commands should I use to clear an old mac address and enable port-security with the new mac address.
i want use CACTI for monitor my bandwidth so i have a question how can i enable snmp for a switch port ? or i shoudl just enable snmp from configuratiopn terminal and then in CACTI i will choose which port will be monitor? can i do something that CACTI connect to my switch with a encryption key ? i have cisco 2960 48 port switch
View 2 Replies View RelatedIn my network we use all cisco 2960 switches, problem is when someone copying 4gb data or high from one switch to another switch, by that time rto (Request time out) is coming.
router
|
|
|
[Code]....
1. when user 1 copy data from server ,at that time who is in switch2 behind like user2 ,he is getting problem like when ping to default-gateway,or rto is coming and network is very slow .
2. when i open sw2,sw1,sw3,trunk ports utilization is very high except sw4 to sw1 trunk ports,who behind sw4 like user4 ,he is not getting problem.
3.all switches trunkport in my network is faster ethernet and i have no option to connect trunkport to gigaehternet and ethernet channel.
I am experiencing the same problem described in this post {URL}. I have seen this happen on different networks, with different equipment attached. It happens on both 2960 and 3750 switches. Basically the connection drops, and we see in the web interface "Port is Disabled". This appears to happen every 10 minutes.
On the CLI, the status shows as connected.
Port Name Status V lan Duplex Speed Type
Fa0/38 connected 1 a-full a-100 10/100BaseTX
I have ran cable diagnostics while the drop out is occurring.
Interface Speed Local pair Pair length Remote pair Pair status
--------- ----- ---------- ----------------- ----------- -------------------
Fa0/38 100M Pair A 28 +/- 15 meters Pair B Normal
[code]...
During the outage, I see the duplex fluctuate between full and half. The outage occurs for approx 90 seconds. If I fix the duplex and speed at both ends, the outage reduces to around 30 seconds. If I apply spanning-tree port fast the outage reduces further to around 10 seconds. Before I change any configuration on the port, the logs show the interface going down
Aug 16 13:06:51.875: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/38, changed state to down
Aug 16 13:06:52.874: %LINK-3-UPDOWN: Interface FastEthernet0/38, changed state to down
[code]...
However, once I apply the configuration nothing is logged. However we can still see the connection is disappearing for around 10 seconds. I suspect the issue wasn't resolved for the person reporting the problem in the link above, but because the outage is minimized, and not being logged it is going unnoticed.
Is there a way to identify if a switch port is burned via CLI? I have a 2960-48PST switch and some ports don't provide power to a PoE device connected. When I change the port, the device turns on.
View 3 Replies View RelatedI want to configure switch port bandwidth limit for my Catalyst 2960-48, is there any hardware / ios limitation? can I configure it at all 48 switch ports?
View 1 Replies View Relatedhow can i limit bandwidth on a gig port of 2960 or 4506e switch?
View 9 Replies View RelatedIs it possible to obtain a replacement rackmount kit for a 2960 48 port switch? I've had a read of the manuals but can't see a part number specified. The part number suggested to me (by BT) is for the 8 port version, which is not much use.
View 2 Replies View RelatedIn s SPAN session , normally the destination prt is used for monitoring purpose only. But could destination port be used to access the equipement or PC connected to that port , for a 2960 LAN BASE image switch .
View 2 Replies View Related