Is it possible to obtain a replacement rackmount kit for a 2960 48 port switch? I've had a read of the manuals but can't see a part number specified. The part number suggested to me (by BT) is for the 8 port version, which is not much use.
View 2 RepliesIf I knew the IP address of a host, can we know on which port on the switch its connected. The switch model is 2960
View 6 Replies View Relatedi want use CACTI for monitor my bandwidth so i have a question how can i enable snmp for a switch port ? or i shoudl just enable snmp from configuratiopn terminal and then in CACTI i will choose which port will be monitor? can i do something that CACTI connect to my switch with a encryption key ? i have cisco 2960 48 port switch
View 2 Replies View RelatedIn my network we use all cisco 2960 switches, problem is when someone copying 4gb data or high from one switch to another switch, by that time rto (Request time out) is coming.
router
|
|
|
[Code]....
1. when user 1 copy data from server ,at that time who is in switch2 behind like user2 ,he is getting problem like when ping to default-gateway,or rto is coming and network is very slow .
2. when i open sw2,sw1,sw3,trunk ports utilization is very high except sw4 to sw1 trunk ports,who behind sw4 like user4 ,he is not getting problem.
3.all switches trunkport in my network is faster ethernet and i have no option to connect trunkport to gigaehternet and ethernet channel.
Is there a way to identify if a switch port is burned via CLI? I have a 2960-48PST switch and some ports don't provide power to a PoE device connected. When I change the port, the device turns on.
View 3 Replies View RelatedI want to configure switch port bandwidth limit for my Catalyst 2960-48, is there any hardware / ios limitation? can I configure it at all 48 switch ports?
View 1 Replies View Relatedhow can i limit bandwidth on a gig port of 2960 or 4506e switch?
View 9 Replies View RelatedI need to configure a Cisco 2960 switch as a DHCP server. The current IP address will be on a different seed than the DHCP addresses. i.e.
Switch IP = 10.1.2.3, GW = 10.1.2.1, Subnet = 255.255.255.0
DHCP addresses would be 192.168.1.1 - 200, GW=???? (10.1.2.3?) and subnet would be 255.255.255.0
2960 switch stack (flex) Spanning tree re-calculate from stack port one?I need to identify with port in the stack is causing the re-calc I have four 48 port switches and show spanning detail only indicates stack port 1.
View 1 Replies View RelatedThis is an easy question for all the architechs and designers out there. I have a stack of 3508-XL switches and one of them failed. we have 2 spares but hese are more than 10 years old and have reaced EoL.What is the equivalent switch of a 3508-xl replacement today?
View 11 Replies View RelatedI have a Cisco SG 300-20 as the core switch, layer 3. It is 192.168.4.6 on VLAN1 and 192.168.5.1 for VLAN2 (VOIP). All the ports are set in trunk mode. DHCP relay is setup on this switch.
The phones connected into a layer 2, Catalyst 2960-S switch. All ports are set in trunk mode. Default gateway on it is set to 192.168.5.1.
DHCP for both VLANs is provided by a Windows Server 2008 R2 server (the relay IP 192.168.4.15).
There is also an ASA 5510 in the mix which is 192.168.4.1. It has a route added to it for the 192.168.5.0 network to go to the SG 300 (192.168.5.1).
Just the two switches can ping each other on the 192.168.5.x network when I "add vlan 2" to the trunk port that is connected between the SG 300 and the 2960. The phones don't get DHCP on the 2960 switch. And I cannot ping 192.168.5.x from the ASA or anything else on the 192.168.4.x network.
After a bit of reading on intra-vlan routing for the SG 300 switch, I am thinking the SG 300 has to be the "center" of things so I need to make it 192.168.4.1 to be the gateway for both VLANs and change the ASA to 192.168.4.2 for VLAN1, etc. And I really can't do asymmetric routing with this switch.
Does the Model "WS-C2960-24PC-L" Supports IP Routing or not?
View 9 Replies View RelatedI'm having trouble setting up SSH on my new Switch.
no aaa new-model
aaa authentication login default local
ip domain-name king.local
[Code].....
I would like to be able to use Vlan 10 192.168.155.1 for SSH remote management.
I have a statck of 4 2960s switches, with POE powered access points on 2 of them. All of the access points appear to be functioning normally. For some reason, on 3 interfaces connected to access points, I get the following when issuing show interfaces status:
Gi3/0/9 connected: T 7 a-full a-1000 10/100/1000BaseTX
^
My question is regarding the "T" in the status field. I can't find any documentation on this.
I have CISCO 2960 switch at my LAN. How to configure its IP address from console or hyper terminal ?
View 11 Replies View RelatedI am trying to configure a new 2960 POE switch, but seem to me the int fa0 is layer 3 interface. Is any way we can convert it to a switchport, so we can connect it to other switch in trunk mode?
View 1 Replies View Relatedi try to implement layer 2 qos in 2960. when i complete to configure the switch, i want to test the qos.PC1 conect to switch port 1,PC2 conect to switch port 2 . PC1 is source teminal. i use skydata.exe and FTP for the test.
when use the skydata ,the PC2 speed can reach 10mbps.when use the FTP , the PC2 only can reach 1.2mbps. why?
I can use Putty to SSH into my new switch (Directly connected to my laptop with ethernet cable), but I cant log into my switch.
Sent username "admin"
admin@192.168.251.1's password:
Access denied
It doesnt like my password, but I have only set 1 password (king) on this switch. I've configured 3 other switches with SSH and had no problem. Been trouble shooting for awhile and It'd be great if I could have a 2nd set of eyes take a peek, Also, my running config is attached.
I am setting up a new 2960-S switch and none of the recommended username and passwords combinations work. I have tried CIsco Cisco, <blank> cisco and various other permutations.
I have tried to reset the switch to factory defaults and it still doesn't work. The switch is currently connected to a 3560G and has been assigned an IP. If I try to access it from Network assistant it shows as unmanaged and I get prompted for a username and password.The switch is connected to another new 2960-S via a FlowStack module.
I have Catalyst 2960 S (WS-C2960S-48FPS-L) Switch. I have plugged in SFP module but still interface is down and line protocol down. Is there any configuration to enable SFP module and make the interface up?
This port is connected to nexus 5 k.
I have a Cisco 2960 48-port switch. I enter "sh vlan" and it lists all the VLAN's. One of the VLAN's listed is "10" with the name "EPIC". What is the quickest way to find out what ports, if any, are assigned to this VLAN?
View 2 Replies View RelatedOur company bought a Cisco 2960-S to add to the network, We gave the interface VLAN 1 an IP address, and tried to attached the switch to a jack port on the wall to test if it gets a link or not. The status of the port blinks amber and stays contionous amber, I have searched the manual of the switch and it says that amber means that the port is being blocked by STP.
View 4 Replies View RelatedI need to know the 172cisco 1 router support to IPv6 & it support to IPv6 then which IOS is required for it.Also I need to know the cisco 2960 switch is support to IPv6?
View 3 Replies View RelatedCurrently Being Moderated password recovery
View 3 Replies View RelatedI am a new network engineer on a retail company and I am having a problem on the High utilization of my 3-stack switch 2960 only during Peak Hours of the Store Sales.
Note: on Peak hours, it is peaking at 90-95 %
here is the utilization after Peak hours:
4444333334444433333333333333333333333333333333333333333333
[Code]......
I can understand it 's one of those very basic questions , but how do I identify a Switch is Layer 2 or Layer 3 ?Looking through # show version command and checking the IOS version to be IP BASE or LAN BASE . Is it the right way ?Cisco 2960 is a Layer 2 or a Layer 3 Switch ? I noticed that access-lists could be configured which means that it 's a Layer 3 Switch , right?
[code]....
I have a Cisco 1841 router connected to a Cisco 2960 switch.Users behind the router can't access the internet but when someone is directly connected to the switch with his PC and uses the IP Address found on the WAN port of the router, he's able to go on to the internet. [code]
View 4 Replies View RelatedToday in my rush to get home I plugged in a new 2960 stack and did a little bit of very basic configuration, but no passwords were set. I tried to telnet in and the message says that a password is required, but none is set. I tried the SDM as I hadn't turned it off yet and it is prompting me for a user/pass but I have no idea what to put in there. No console is available, it's a new office so no employees around either.
View 14 Replies View Relatedi am facing time daely issues on cisco 2960 s series switch while booting .It is taking time for electing masrer and sleeve for stacking.can i disable the election process for stcking while booting.
View 4 Replies View RelatedConfiguration details: I have 2 nexus 5K switches and both 5K is connected to four 2960 access switches in each floor through fiber(shown in the attached picture). I have configured each VPC for each floor and portchannel configuration on 2960s switch to communicate to 5K switches. Now I am not able to communicate PC 1 connected in 1st floor to PC2 connected in 4th Floor.
I have attached topology map of my infra and the configuration files also. 1st floor switch and 4th floor swich have same configuration except IP address and switch name.
Document at url... is quite interesting,One of these goes about the behavior of a switch (2960-S and 3750G) when QoS is not enabled vs the one when QoS is simply enabled with "mls qos".What additional commands, beside "mls qos", would be needed so as to simulate as accurately as possible the switch's behavior when QoS is not enabled?
View 3 Replies View RelatedI have a client whom has asked me to enable web management on some of his 2960 switches. I did not think this was going to be an issue, and so I told the customer I would set this up for him.
Much to my dismay, I have been able to get http and https enabled, and then authenticating locally for the HTTP access. I then come to the screen once authenticated which is shown below:
The issue is that when I select "Web Console", it gives me a "Web Page Cannot be found".
I have a Cisco 2960-S Switch, It is connected to a jack in the building to check the settings, Interface VLAN 1 has an ip, there is a default gateway, Any host connected to switch can access the network resources. But the problem is that I have to use Serial Cable to configure it. I cant ping or telnet into it from any other device. PC's are on different subnets/VLANS.
Basically this switch is connected to a port in a different switch, Do i have to make a trunk?