Cisco Switching/Routing :: Nexus 7K (6.x) / SPAN To Multiple Destinations Does Not Work
May 18, 2013
I have a single Nexus 7K (6.x) with only F2 modules and I would like to SPAN the same source interfaces and vlans to mulitple destination servers (interfaces). When configuring SPAN to a single destination traffic gets replicated successfully but when I add an additional destination to the same SPAN session then none of the destination interfaces receive any traffic. As soon as modify the SPAN to include only a single destination interface it works again. I'm guess this is a limitation of the Nexus 7K 6.x code or the F2 modules.
View 4 Replies
ADVERTISEMENT
May 29, 2013
I want to monitor our backup server (commvault) as it is saying it's library (Data Domain) is going off line.[code] The issue is I am seeing a lot of unicast traffic (on Wireshark) that has nothing to do with the server on E2/11. Some of it is from different VLANs... There is way too much data (multi-Mbps) to keep wireshark running very long to capture our intermitten problem.
View 3 Replies
View Related
Apr 18, 2012
I've learned recently that the Nexus 7000 only allows the configuration of a maximum of 2 Monitor sessions for spanning traffic. I only have one monitor session left and I need to do the following. 2 Core Nexus 7000 boxes with 2 different traffic probes/sniffers to each nexus( eg Sniffer 1 connects to Switch A on interface eth 1 and to Switch B on eth 1 ; Sniffer 2 connects to Switch A on eth 2 and to Switch B on eth 2.) My plan was to setup a standard session with multiple sources and destinations then on the interfaces connecting to the sniffers run a trunk and do 'sw trunk allowed xxxxx' and filter what I need to go to each sniffer box. However I've recently found out that some of my source traffic is coming from Port-Channel interfaces. Is there a way I can get around this and still do the filtering within only 1 monitor session ?
View 1 Replies
View Related
Oct 24, 2011
I am in the early planning stages for a 6509 to Nexus 7K migration. Based on my experience with the 7K's at a previous company where we ran into a lot of issues, I am trying to be very careful.
I am more at home with the 6500 chassis and know what I can do with them. I remember running into a limitation on the Nexus that involved their not supporting span sessions like the 6500's do. Is that still the case ?
If that isnt an option in the short term, I will need to look at a substantial investment in ethernet tap's to replace the lost span functionality because the security group's heavy use of span sessions.
View 1 Replies
View Related
Jun 9, 2013
I'm setting up a montitor session on a NEXUS 7K as below.we are receiving in 150M of data and 0 data going out port 9/25.but port 4/24 shows 300M to the span port?
View 1 Replies
View Related
Mar 3, 2013
rsbd7k01-p-vdca(config)# monitor session 2
rsbd7k01-p-vdca(config-monitor)# source vlan ?
<1-3967>
rsbd7k01-p-vdca(config-monitor)# source vlan 1 - 3967
ERROR: vlan 33-3967: Number of source vlans exceeds maximum
rsbd7k01-p-vdca(config-monitor)#
View 3 Replies
View Related
Sep 6, 2012
I need to move 1 data stream onto 4 different servers in different subnets, I know I can NAT into a multicast address, but with it coming into an ASA I was wondering if I could make a PAT that sees packets coming in on port 4567 and sends it out to port 4567 on 4 other IPs (I don't think this will work though as I don't think a pat will duplicate packets, only change them)
View 2 Replies
View Related
Apr 17, 2012
Anyone got a single VSM (albiet in HA) managing two vDS split over two ESX clusters connected to a single instance of vCenter?
View 0 Replies
View Related
Aug 31, 2011
Can the camera support multiple destinations simultaneously?
In testing set-up for ftp and email, while observing results in a browser on the Mac, and also MyDlink app on an iPad, I observe that a few jpegs get sent to email, a few to ftp, and MyDlink keeps "timing out". My Mac is wired gigabit ethernet to the router, and the wireless LAN is 802.11n.
Maybe it can't handle multiple destinations?
Does MyDlink cause continued transmissions at the video frame rate set in the setup panel, even if no one is connected to look.
View 14 Replies
View Related
Nov 13, 2011
I have a customer with three rooms where teh access layer aggregation switches are run back to.
Access Switch Stack A -> room 1 + room 2
Access Switch Stack B -> room 2 + room 3
Is it possible to have three Nexus 7000s ie one in each room (1,2 and 3) and have them setup like this:
Nexus 7000#1 vPC domain 1
Nexus 7000#2 vPC domain 1 + vPC domain 2
Nexus 7000#3 vPC domain 2
Thus gving all access switch stacks redundant links to the core withouit spanning tree.
I know its not ideal but its a campus site and thats how the existing fibre runs go.
View 5 Replies
View Related
Mar 30, 2012
I have a senario where i'm going to have 2 Nexus 7010 connected as a core, and i'm going to have 4 5510's connected in a star formation. Each nexus 5510 will connect to the nexus core Via two 10Gb links. Each nexus 5510 will have 2 links attached to The core switches in vPc's.
Nexus 7010-1 = Core 1
Nexus 7010-2 = Core 2
Nexus 5510-1 = vPC = 100 2 Ports in vPc 100 -- > 7010-1, 7010-2
Nexus 5510-2 = vPC = 200 2 Ports in vPC 200 -- > 7010-1, 7010-2
Nexus 5510-3 = vPC = 100 2 Ports in vPc 300 -- > 7010-1, 7010-2
Nexus 5510-4 = vPC = 200 2 Ports in vPC 400 -- > 7010-1, 7010-2
The way I intend to configure the vPC's is this the best way. If i get a vPC dual active scenario what would happen. All ports will be forwarding all VLAN traffic this is how I intend to have it work.
View 14 Replies
View Related
Dec 5, 2011
I cannot get the AAA tacacs+ authentication to work on my Nexus 7000.
View 4 Replies
View Related
Nov 5, 2012
i would like to monitor traffic between multiple source ports to multiple destination ports on a nexus 7k. i lknow when you set up monitor session is between source and destination (laptop or traffic analyser) but is there a way i can set up between source and multiple destination ports and capture that traffic ?
View 3 Replies
View Related
Sep 10, 2012
I've been testing some QoS policies, and I have not been able to make a type QoS policy work in the outbound direction. Simple example:
ip access-list QOS-VOICE
10 permit ip any 10.120.11.0/24
20 permit ip 10.120.11.0/24 any
class-map type qos match-any IN-VOICE
description Voice/VoIP/IPT
[code]....
The 7Ks are running NX-OS 5.2(4). Just wondering - has any one got an outbound qos policy to work on a N7K?
View 2 Replies
View Related
Sep 10, 2012
we've been using IOS for a long time, but are relatively new to NX-OS. We've got a central syslog server that all our devices log to. No matter what we do, we can't get our Nexus switches to log there. Here's my current attempt:
Nexus 7009, NX-OS 6.0(1)
# sh logging server
Logging server: enabled
{redacted}
server severity: debugging
server facility: local7
server VRF: default
[code].....
The default VRF is working. I see log entries in the logfile, but nothing arrives at the syslog server. It's not a config issue on the server, because tcpdump shows that no packets arrive from the IP for loopback 0.
View 3 Replies
View Related
Apr 26, 2012
Trying to get the peer links to work and have them in interfaces E1/1-4 . When i do a show int status it looks like this and says sfp invalid. I see this on both sides. These same model gbics work fine attached to a FEX on these boxes.
Eth1/1 vpc peer link to T sfpInvali trunk full 10G Fabric Exte
Eth1/2 vpc peer link to T sfpInvali trunk full 10G Fabric Exte
Eth1/3 vpc peer link to T sfpInvali trunk full 10G Fabric Exte
Eth1/4 vpc peer link to T sfpInvali trunk full 10G Fabric Exte
Gbic in ports are this.
Ethernet1/1-4
transceiver is present
type is Fabric Extender Transceiver
name is CISCO-FINISAR
part number is FTLX8570D3BCL-C1
[code]....
View 5 Replies
View Related
Dec 6, 2011
I am trying to configure get the QLogic 8240 card to work properly in ESXi 5.0. I want to be able to send the iSCSI traffic down the iSCSI portion of the card and use the ethernet portion of the card to do NFS.
Here are my vlans I am working with..
vlan 420 = fcoe
vlan 500 = NFS
vlan 1000 = iSCSI
I have my interface currenly set as the following on the Nexus 5000.
interface Ethernet1/17
[Code]...
View 5 Replies
View Related
Mar 19, 2013
Does Nexus 7K support Multiple VDCs sharing ports on a single line card. One of our cisco parnter engineers stated that cisco doenst recommend using same line card for multiple VDCs.The second VDC (Non-Default VDC) will be used four our Outside, and DMZ Segment, and to phyiscally segregate our Firewall from our Internal/Inside Core Switch without using a physical DMZ Switch.I know Cisco used the Nexus in this way in their PCI DSS 2.0 Compliance Document. Module is N7K-M148GT-11L
Mod Ports Module-Type Model Status
--- ----- -------------------------------- ------------------ ------------
1 48 10/100/1000 Mbps Ethernet XL Mod N7K-M148GT-11L
Mod Ports Module-Type Model Status
--- ----- -------------------------------- ------------------ ------------
1 48 10/100/1000 Mbps Ethernet XL Mod N7K-M148GT-11L
View 7 Replies
View Related
Feb 22, 2012
I am trying to configerate static switchports on our nexus 5548 (nx-os 5.1(3)N1(1)) over snmp.The support-list url... states that the CISCO- VLAN- MEMBERSHIP- MIB is supported.I can read the information, but if i try to set vmVlan or vmVlanType i get the message: "SET failed. ("ip-address"). Information: Not Writable."I can use set_request in general (e.g. CISCO-CONFIG-COPY-MIB). how to set the vlan and vlan-type over snmp?
View 3 Replies
View Related
Dec 13, 2011
I am hoping you can provide me with some opinions, feedback, thoughts on the following. We have some Cisco 6509 switches in our environment currently hitting around 60% usage on the Router overall statistics.
Now we are looking at implementing an intrusion detection system but by being as least invasive as possible to the network. Our thoughts are to utilize a SPAN port on the switches to send traffic to the NIDS device but we have concerns of the following. The limitations of SPAN sessions on 6509's . The overhead on the switch of turning a SPAN session on and leaving it on permanently.
View 1 Replies
View Related
Mar 12, 2013
I am trying to configure RSPAN for one of my client. They have Server-Client VTP architecture. Voice Recording Server is connected to C4507. Agents are connected to C2960 and C3750. I got 2 sessions configured and the connectivity is a as follows:
1. Voice Recording Server-----C4507-----C2960-----C2960-----Agent IP Phones (Session 1)
2. Voice Recording Server-----C4507-----C3750-----Agent IP Phones (Session 2)
Recording works with Session-2 but not with Session-1. I understand the problem could be due to multiple reasons: 1.1. C2960 is working in client VTP mode so i cannot add remote span command under the vlan configuration. 1.2. C2960 has LANLITE IOS image which i am not sure if it supports Remote Span.
View 2 Replies
View Related
Dec 31, 2011
I have CISCO catalyst with VLANs (VLAN ID 33, 36, 40-53) configured. I need to configure port mirroring in Switch 3750 for NAC (Network Access Control). I need to Monitor all the VLANs. Here is the SPAN configuration of switch: [code] Monitor session 1 source vlan 33 , 36 , 40 – 53.Monitor Session 1 destination interface fa 1/0/8 (here I am not able to set encapsulation dot1q ) because the error occurred saying %one or more dest port do not support the encapsulation%.
View 5 Replies
View Related
Feb 12, 2013
I currently have IOS image cat4500e-entservices-mz.122-53.SG5.bin. According to my research it appears SPAN is supported on this OS. However, after looking at procedure notes using websites like here:
[url]... I cannot find and obviously not figure out how to use the SPAN command. My main objective is to simply setup a port mirror on one of my TenGigabitEthnet interfaces and from what I read SPAN is the best way to setup a tap interface on a cisco switch.
View 2 Replies
View Related
Dec 12, 2011
Been dealing with a strange problem for several days now. It started out with a problem that I thought was VTP related but ended up being something else. I setup a span port on a 3750 that I am connected to that was mirroring the trunk connection coming into the switch.
Never saw an VTP traffic come across the connection but doing a sh vtp status indicated the traffic was arriving and getting processed. When I found some debug commands (debug sw-lan vtp), I was also able to see the packets go between switches. Seeing this issue concerns me that there is other traffic that isnt showing up during a span session.
I know that doing a span on a switch, especially using a trunk port as a source, isnt a good idea. Since I didnt have a TAP at time, this was my only choice. I have since borrowed a NetOptics TP-CU3 tap from a good friend and was able to confirm the VTP traffic was going across the trunk connection between switches.
All of my 3750's are running 12.2.55.SE.
View 8 Replies
View Related
May 1, 2013
I have a Cisco 881 router running 15.1(4)M4. I am trying to configure SPAN on it to mirror my outside interface (source) to one of my LAN interfaces (dest).
!--- WAN interface
interface FastEthernet4
description Comcast WAN$ETH-WAN$
[Code]......
As you can see from the above output there is a problem with the command on this interface. When I try to set Fa0 as my source it works fine:
rtr(config)#mon session 1 source int fastEthernet 0
rtr(config)#
Is this because fa4 is layer 3 and fa0 is a switchport? If so, is there another way to set fa4 as the source?
View 4 Replies
View Related
Jul 12, 2012
I have a need to capture some traffic but my core 6513's are already using the limit of 2 span sessions. I can't edit any of the sessions either because I want to source traffic from vlans and you can only do one or the other. Is using a VACL with 'switchport capture' on the destination interface an option ? E.g. I want to source traffic from vlan 10,20,30,40 and send the all to interface Gi10/10 ? Is there any caveats ? I dont need to be too granular with the ACL's but just capture all traffic in those vlans.
View 2 Replies
View Related
Mar 16, 2011
i will be creating combination of SPAN and RSPAN on catalyst 6506 according to the link
[URL]
im planning to implement this on two 6506 switches will this work? or do i violate the number of monitor session? sorce span?
sw1
monitor session 1 source interface Fa5/18monitor session 1 destination interface Fa5/48
monitor session 2 source interface Fa6/34monitor session 2 destination interface
[Code].....
View 1 Replies
View Related
Sep 16, 2012
i have configured SPAN on cisco 4900 series switches its a Loacal SPAN . as there is only commnads to complete this activity but hard luck its not working.
View 5 Replies
View Related
Jul 3, 2012
I have configured SPAN in cisco 3750 switch as below mentioned. but the destination port protocol is down.
Network Diagram:
switch(config)#monitor session 1 source interface gigabitethernet1/0/1switch(config)#monitor session 1 destination interface gigabitethernet1/0/11 ingress vlan 1
[Code]....
View 8 Replies
View Related
May 26, 2013
I have cisco 2651 with one L3 interface ip 172.26.18.200. This Cisco is gateway from E1 PRI (PBX Aastra MX-ONE TSW) to SIP (Asterisk). This cisco 2651 connected to cisco 2950 in port Fa 0/12. Fa 0/12 is in VLAN 518 (dot1q).
On cisco 2950 i made next commands:
# monitor session 1 source interface Fa 0/12 both encap dot1q
# monitor session 1 destination interface Fa 0/9
#sho monitor session 1
[Code].....
View 2 Replies
View Related
May 23, 2012
I'm trying to configure a mirror port on a 3750. This configuration needs to replicate data from local ports, but I need that also act as a regular access port.
With the initial configuration, SPAN port, there is no problem, all the data of the configurated ports is replicating in the configurated port. On the port configurated as mirror there is a PC connected for audio recording. When the port is not operating as SPAN there is communications without problem over the LAN. But when I configure the port as SPAN, communication is interrupted.
Here is the actual configuration:
SWITCH1-PISO7#sh monitor session 1
Session 1
---------
Type : Local Session
[Code]......
View 5 Replies
View Related
Dec 30, 2009
I do not see 802.1Q tags nor do I see p-bits (COS) in my wireshark captures. My setup is not working and I have no way to verify (sniff) that the 6509 is setting the p-bits to 3. [code]
View 4 Replies
View Related
Jun 8, 2012
i have configured SPAN over cisco 2960 to monitor source port traffic but after configuration i dont able to get response from destination port as my NMS is attached on destination port so i lost its web interface.
Configuration is as under.
monitor session 1 source interface gigabitEthernet0/5 (Source Port on Vlan 100) monitor session 1 destination interface gigabitEthernet0/1 (Destination Port on Vlan 200)
View 2 Replies
View Related
