I need to move 1 data stream onto 4 different servers in different subnets, I know I can NAT into a multicast address, but with it coming into an ASA I was wondering if I could make a PAT that sees packets coming in on port 4567 and sends it out to port 4567 on 4 other IPs (I don't think this will work though as I don't think a pat will duplicate packets, only change them)
View 2 RepliesIn the Firewall Dashboard of my ASA 5580, I get data on every pane, except for the Top 10 Sources and Top 10 Destinations. Why is that, and what do I need to do to get data there?
View 1 Replies View RelatedCan the camera support multiple destinations simultaneously?
In testing set-up for ftp and email, while observing results in a browser on the Mac, and also MyDlink app on an iPad, I observe that a few jpegs get sent to email, a few to ftp, and MyDlink keeps "timing out". My Mac is wired gigabit ethernet to the router, and the wireless LAN is 802.11n.
Maybe it can't handle multiple destinations?
Does MyDlink cause continued transmissions at the video frame rate set in the setup panel, even if no one is connected to look.
I have a single Nexus 7K (6.x) with only F2 modules and I would like to SPAN the same source interfaces and vlans to mulitple destination servers (interfaces). When configuring SPAN to a single destination traffic gets replicated successfully but when I add an additional destination to the same SPAN session then none of the destination interfaces receive any traffic. As soon as modify the SPAN to include only a single destination interface it works again. I'm guess this is a limitation of the Nexus 7K 6.x code or the F2 modules.
View 4 Replies View RelatedWe have inherited a 5508 controller running 7.0 code and WCS running 7.0 code. This site did not have a backup controller. So we have installed a wism as a backup controller. The problem is no one can seem to remember the pre shared keys for the wlans on the primary controller. Can I use WCS to duplicate the wlans to the secondary controller and have the psk copied?
View 3 Replies View RelatedI have a virtualization server with 4 network interfaces and connected it to a SAN. There are few virtual machines which writes data to the SAN.
I want to connect to the SAN with multiple interfaces to speed up the network.
Is it possible to send data on multiple interfaces? How can I configure it?
Computers are connected to san through switch.
SAN: Equallogic PS 4100 E
Switch: Dell Power Connect
Computer: Dell T610
OS: Centos 5
Virtualization: Kvm
NIC: 8
I am not sure about network card brand now.
After upgrading to 8.4(2) and ASDM 6.4(5) I seem to have an extra access rule duplicating an existing rule, this is only visable through the ASDM. When using the CLI you can't see this duplicate rule.
I therfore get the following warning everytime I make a config change using the ASDM [code] If I delete this rule it returns everytime I launch the ASDM!
I also have extra config under Firewall>Configuration>Public Servers that I didn't have before. If I delete it, again it returns.
after upgrading an ASA 5520 to 8.4.2-8 VPN clients traffic is not passing destinations other then destinations behind the inside interface. the log shows routing failure for the vpn client on the inside interface.it was working fine with 8.4.1 but the traffic is originated from the outside interface. confirm the the interface for VPN clients changed from outside to the inside interface.
View 5 Replies View Relatedhow to: port forwarding to 2 different destinations based on incoming WAN port
The default HTTP service works fine: TCP80/80-> 192.168.0.55
I have a couple of IP security camera's I'd like to be able to access remotely that also listen on port 80. I tried TCP & UDP 8009/8009-> 192.168.0.9 without any luck. Not sure how to handle the port redirects on the RV042G? Seems simple and was on the Symantec, could be user training :-)
I was able to do port redirect with the Symantec Firewall I'm replacing.
how i can configure a second ssid for guest access in our environment. this is our network setup prior to this request: Internet----Firewall (not ASA)---ce520---C1131AG and CME router is also connecting to the ce520 switch. we only have two vlans: one for voice and two for data.
Presently, there is no vlan configured on the AP because it on broadcasting ont ssid and wireless users gets IP from a windows DHCP server on the LAN. the configuration on the ce520 switch port for the AP and other switches say access vlan is the DATA vlan which automatically becomes the native vlan for all trunk port connecting the AP and other Stiches to the network.
Now with this new requirement, i have made my research and i have configured the AP to broadcast both the production and the guest Vlans. The two vlans are 20-DATA and 60-Guest. I made the DATA vlan on the AP the native vlan since the poe switch is using the DATA vlan as native on the trunk ports. I configured the firewall to serve as DHCP server for the guest ssid and i have added the ip helper-address on the guest vlan interface on all switches while the windows server remains the dhcp server for the production DATA Vlan. I have confirmed that the AP, switches can ping the default gateway of the guest dhcp server which is another interface on the firewall. I can now see and connect to all broadcasted ssids but the problem is I am not getting IP addresses from both the production dhcp server and guest dhcp server when i connected to the ssid one at a time. My AP config is attached below.
Do i need to redesign the whole network to have a native vlan other nthan the data vlan? Does the access point need to be aware of the voice vlan? Do the native Vlan on the AP need to be in Bridge-group 1 or can i leave it in bridge-group 20?
My question is if I can configure 3 ssid, for 3 different VLAN and add the DHCP address from a WAP4410N AP, when you upgrade to the latest version of IOS I can have this functionality?
View 2 Replies View RelatedIs it possible to have multiple dhcp pools for multiple VLANs? The switch is a 6509 and/or 4506 catalyst. I don't want to use server-based products.
View 5 Replies View RelatedI am trying to build a new network from scratch, I have the WLC 5508 w/ Aironet 3600e APs connected to my Netgear Smart Switches and a Linksys RV082 router that I'm using as my DHCP server with several VLANs for several stuff on my Switches.
I have 2 questions:
1. Can I have 5 Interfaces configured on 5 different VLANs, each SSID on each a different Port:
Port 1: Controller management only=> 192.168.x.x /24
Port 2: SSID 1: WiFi Internal=> 172.16.x.x/12 (Radius Auth with no sharing)
Port 3: SSID 2: WiFi Internal w/ sharing=> 192.168.x.x/24 (Radius Auth with sharing)
Port 4 :SSID 3: WiFi Guest=> 10.0.x.x/8 (Web Auth)
Port 5: SSID 4: WiFi IT=> 192.168.x.x/24 ( Radius or certificate Auth with access to the controller management interface)
2. How can I use the Controller as the DHCP server for all the WiFi traffic, and how should that be configured to work with my other DHCP server?
i`m facing a problem configuring the mentioned access point to act as stand alone access point with multiple SSID assigned to differnet VLANs the problem is that
1) i`m not able to broadcast the both SSIDs in the same time from the Access point
2) i need to make the radius server to manage the SSID access for the wireless clients (trying to find a way in which the aceess point sends a log for the radius server containing the VLAN id /IP address of the the SSID) you may find the below info about the IOS ver. & the configuration?
i`m running IOS /c1100-k9w7-mx.123-8.JEE/c1100-k9w7-mx.123-8.JEE?
Is it possible to assign a single ssid to multiple interface groups by assigning the ssid to multiple AP groups?
I have buildings geographically dispersed that are configured with multiple vlans in interface groups so that I can maintain an addressing scheme of dhcp assigned addresses per building. Each building is also further grouped as AP groups. I'd like to know if by assigning the same wlan ssid to each of the AP groups, will I maintain addressing integrity for each building? I'm thinking it will work.
Do the buildings have to be outside AP range of each other to avoid problems?
5508 controller
7.2.110.0 code
6 buildings
6 interface groups
1 ssid
Just recently installed CW LMS 4.1. In the Configuration Dashboard you can see Discrepancies and Best Prctice Deviation. In our old 4.0 it shows a list of both discrancies and bestpracice deviation. In our new 4.1 we only see "No data is available", so I guess I need to do som work but can figure out where and what.
View 3 Replies View RelatedAre there any methods for statistic data importing from old LMS 3.2 to a new LMS 3.1 version? I know about devices invemtory export/import function, but also i want to save all data gathered from previous time.
View 1 Replies View RelatedI am working on a migration from Windows based WCS 7.0.164.3 to NCS appliance (1.2.1-once it is available). After stopping WCS, I issued the export userdata C:WCS07Migrate. The process completed, but did not create a single zip file. I found 2 files created in the tmp directory.
One contains multiple a folder called tempDirUserDataFromDb - containing multiple xml files; and another file called ImportExport_ca<number> which contains the maps. Was there something incorrect in my command? Can I use still use these files on NCS? Or do I need to redo the export on the WCS?
I need to migrate DFM alarm settings data from LMS 3.1 to LMS 4.2.3 and I want to use this method, [URL] , to extract the data from 3.1 and then inport it into 4.2.3.
I successfully performed it for IP settings, it was easy since the data format was the same.
But the format differs quite alot for Interface and Port data, here is an example:
export from LMS 3.1
IF-hostname/17 [Gi0/0.524] [10.55.254.3]; INTERFACE:;IF-hostname/17; MANAGED_STATE:;EXPLICITLY_UNMANAGED
export from LMS 4.2.3
INTERFACE:IF-hostname/17 MANAGED_STATE:MANAGED GigabitEthernet0/0.524
It looks like I have convert interface names, sort and delete stuff to make it look the same.
If I have two E1 router directly connected each other by using G.703 unframe method for data transimission. How to configure the router? Any sample configuration?
View 2 Replies View RelatedI'm trying to migrate old data from WCS 7.0 to Prime 1.2 ... I have already created the zip file from WCS and imported it into the defaultRepo on Prime. I see it in the directory when I do a show repository defaultRepo so I have confirmed that it is there. My issue is that it appears Prime 1.2.1.012 won't accept the cli command of ncs migrate.
how I can proceed with the migration? I haven't been able to find any similar command in the Prime CLI so at this point I'm lost as to where I should go from here. I really don't want to have to tell the customer they have to downgrade to Prime 1.1 in order for them to perserve their maps especially since the Deployment Guide for Prime Infrastructure states that it is possible to migrate date from WCS 7.0 to Prime 1.2 as shown below ...
Data Migration
#
Data can be migrated from WCS 7.0, NCS 1.1, or LMS 4.x. More details on migrating data from each of these applications are spelled out in the following sections.
[Code].....
i have an issue with the lms 4.2 Topology Data Collection. After installation the Topology Data Collection was running normaly, but since first server reload the Topo Data Collect under Inventory > Dashboards > Device Status > Collection Summary is "frozen".Is there any option to stop this process elsewhere? I cannot find anything under jobs in running state or so. Clicking on Schedule only give me the option to start data collection, but lms always returns that the process is running.
View 9 Replies View RelatedI am currently using a 1841 router with AdvSec 12.4(24)T4 IOS on it. I used to have a working SSL tunnel configuration working, but for some reason it had disappeared and I am rebuilding the configuration. Unfortunately, I have been able to configure the router to perform the SSL tunnel, but I am not able to pass any data through the VPN. I am only able to ping the inside interface of the router and this is it. If I try to extended PING from the router to the remote PC I am able to get replies. Trying to PING anything on the remote network does not provide any responses back. I am thinking there is some sort of routing not happening here or I am missing some sort of configuration to allow the VPN to pass data through correctly. [code]
View 2 Replies View Relatedwe demo'd a 3500 with CleanAir before working with Cisco and purchasing a first batch. The demo worked as expected, just plugged it in and it went to town serving clients and reporting on it's channel in local mode, no problem. My first batch I have two AP's, 3502i's to be exact, plugged in and running on my 5508 with 7.0.98.0 code and and NCS Demo. The AP is up and serving in local mode, however NCS says CleanAir Management Operation StateDown
I took a look at the WLC and it says:
CleanAir
Oper
Status DOWN
So, why.. and where do I put it UP.BTW, this AP is connected to a 3750x stack, shouldn't be an issue there...
We have to ACS cisco Box running software as 4.2 & 5.2. We want to upload all the data present in 4.2 ACS to 5.2 ACS.
View 6 Replies View RelatedHave a problem coming my way with regards monitoring 3g data usage on an 887 router. The router will carry two links - x1 primary over the serial port and x1 secondary failover link utilizing 3g.
The 3g sim has an allowance of 1Gb per month (traffic has been baselined and this seems sufficient - not by me though).I have a requirement to monitor the 3g link and trigger an alert at say the 60% mark (600Mb). Whatever mechanism is used to count the data also has to reset to 0 at the beginning of every month as data stats will be included in monthly reports.
Second conundrum, I also have to somehow split out the data usage stats to show my customers usage as well as my own. My own being management traffic (mainly snmp and icmp) and present this in the monthly report.
#1 - Does the 887 have some form of 3g accounting capability either via gui or cli that can fulfil my requirements above?
#2 - With splitting the data usage stats, could this be achieved using netflow and if it was possible, could i only have my flows sent down the Primary link (obviously only when it is active) and if the box fails to 3g have netflow just count the data until the Primary kicks in again.If no built in features can give me what i want i my go down the eem scripting route burt this is a last resort.
I would like to empty my LMS 3.2 DB and re-discover all of my devices again. What is the best way to do this besides wiping the software and reinstalling?
View 1 Replies View RelatedI have a problem with the User Tracking and Data Collection on LMS 4.0.1 . I think It crashes every time or freezes. I Have this error if I lunch UT Acquisition :
Failed to start acquisition: Construction of XML data required for UT IS in progress. Please try After Some Time.When scheduling a CM data collection, I have this error: Data collection IS Already in progress.
I detected an error in ani.log line 12266: Exception in thread "Discovery" java.lang.AbstractMethodError: com. cisco. nm. ani. server. topo. Port Channel.portIfIndex ()
I successfully changed the name of the CiscoWorks server last week with the tool hostnamechange.pl.
Perhaps there was an impact on data collection ?
Got an problem with LMS 3.2/Solaris.
See no devices both in DCR and RME, besides, in RME device counters (Normal/Pending/etc) are equal to current device count, but then you try to select them for any operation, you unsucceed - 0 device selected, no list of devices, unable to export, no ability to do anything.
Upgraded to 3.2 SP1, no change. Spend a lot of time digging through logs at /usr/adm/CSCOpx/logs, find no problems at all. Seems, that some database parts were corrupted.
I decided to reinstall LMS from the scratch, but to do so I need to export the DCR device data and credentials.
Database is alive (dbaccess.pl install going smoothly, then connection with user lmsdatafeed works and allows to connect and select data from any SQL tool), but this view is not enough for getting from the DCR both device data and credentials.
I have the DB password I set up during installation.
Is there any way to get data I need connecting to LMS database directly with some kind of sysdba SQL database user?
we have installed LMS 3.2 when i try to run data collection it shows "Notified server to run campus data collection", but status of data collection is idle.
If i restart the server and try to run data collection it runs properly one time.
Each time i have to restart the server for data collection.
Since CIPC is isntalled in the PC, and PC definitely getting an IP address from the data IP network segment instead of the voice IP network segment, so how to gurantee the following? 1. How the CIPC registered to the CME/CUCM 2. How to gurantee the QoS for the CIPC's voice traffic since the source IP address of the CIPC is belong to the IP network segment?
View 4 Replies View RelatedI just managed to get my hands on a CISCO 871 router but when I turn it on I have some errors:
*** Data Access Exception ***
PC = 0xfff3026c, Vector = 0x300, SP = 0x8000498c
The first time I powered on the router it booted, then I turn it off and since then I have this errors every time it boots up. If someone can give some info about the errors so I can try to remediate.
[Code]....
I think I understand purging in ACS5 now:Purging occurs when the database either gets too large or when data is too old (up to 12 months, although I assume you can leave the setting blank and no age related purging takes place?)Data is purged by making incremental backups and deleting the backed up data from the local database until the size/age pressure is relieved.So, my question is, how do I later look at the purged data? If I suddenly need to look at logs from last year what am I supposed to do? If I restore it surely I'm just going to go over the size limit again and it'll just get purged, no?
View 6 Replies View Related