I have the cisco 3640 with IOS Version 12.2(46) , and it with DRAM:32M , Flash:8M.What IOS version can support IPv6 RIP in the hardware limit?
View 3 RepliesI Have a requirement to migrate from ipv4 to ipv6, I have checked the scalability of all the devices for this migration except ACS 1113 Solution Engine, Version 4.2. I couldnt reach the proper documentation to check its support for ipv6.
View 1 Replies View RelatedI have cisco 2960 and Catlyst 4510 switches now we are planning to implement IPV6.
i have the fallowing IOS on my switches.
C2960-lanbasek9-mz.122-50.se5
Cat4500e-entservicesk9-mz.122-54.sg1.bin
The above ios will support for IPV6 or I have to purchase new IOS, which version will support.
I am having WS-C3560G-48TS switch with ios(c3560-ipbasek9-mz.122-58.E2.bin) and I am trying to use IPv6 feature in this switch model. More over I've upgraded this switch with many ios but none of them not supporting IPv6 feature. ios which supports IPv6 feature?
View 3 Replies View RelatedI need to confirm that the 4510R+E switch with the SUB7-E/2 running version 15 IOS will not support NAT. I am 99% convinced that it does not but i am looking for confirmation, as i am a bit surprised by the lack of NAT support on this platform.
View 0 Replies View RelatedDoes the 3750G-12S-E support Advanced IP Services version of IOS?
View 3 Replies View RelatedI'm using 3640 router running on c3640-js-mz.124-25d.bin IOS. I'm using NM-1A-OC3SML= (ATM OC3, long reach single mode) interface card. Now my pc is connected an fast ethernet interface of the router. Need to know the ATM configuration on this cisco 3640 router in order to achieve the ATM over ethernet traffic get success. As of now i've confugred as below but it's not working it seems.
interface ATM2/0
bandwidth 120000
ip address 10.2.2.1 255.255.255.0
no atm ilmi-keepalive
pvc 0/36
protocol ip 10.2.2.10 broadcast
cbr 70000
encapsulation aal5mux ip
let me know the correct encapsulation type for the connectivity.
The Cisco 3600 series (3640) is hanged during booting proccess, the IOS is decompressed, but after some text it hanges and I even cannot go to user exec. ROMmon and bypassing the config setting, but the result is still the same.
View 5 Replies View RelatedI got this 3640, trying to apply a service-policy (output and input), but seems like I do it something wrong...because he only apply the output policy... here the config, I already try to config the service police inside the fa0/0, but is not showed at all, he only show the output, its like I never apply that
View 1 Replies View RelatedI got some unexpected System crash, and this happens to 2 different routers on the same network.. (We suffer a Crash and change the router, happens the same to the new router after some time, maybe 40 minutes!!)
Here is the last console report for the new router....
%Software-forced reload
Preparing to dump core...
4w1d: %SYS-2-WATCHDOG: Process aborted on watchdog timeout, process = IP NAT Age
[Code]....
We have a Cisco 3640 router running c3640-is-mz.123-3g.bin Switching ports are devided into several VLans. Each VLan has its own IP subnet. We can't ping IP address X in subnet A from subnet B unless we log into the router and ping it from there first. (and then the IP address will show up in "show ip arp" command. Then we can ping X in subnet A from subnet B, and browse web on device X from subnet B, etc. )
View 6 Replies View Relatedi am running c3640-is-mz.124-21.bin on a cisco router 3640. i am trying to create a monitor session in the CLI and everytime i type the command Router(config)#monitor session 1 interface ethernet2/1 % Invalid input detected at '^' marker. Router(config)#monitor session 1 interface ethernet2/1 ^% Invalid input detected at '^' marker. i get the error invalid input ?
View 10 Replies View RelatedSo I have 2 routers (cisco 3640) that each go to their own ISP and then back to the same switch. I have setup ospf and glbp, and now have pretty good redundancy. If either internet connection or routers go down everything is still golden.
So I was thinking that if an interface went down then the router would not be load balanced with glbp which got me thinking whats the best way to get interface redundancy (and I was going to add a 2nd switch with the second interface).
1) Setup BVI on the 2 interfaces.
2) Setup a 2nd interfaces (on each router), I would have to split the subnet, for instance: [code]then the machines could be on the subnet 192.168.0. 0/23 and setup glbp for 1 ip across all 4 interfaces (I'm not even sure if you can do this but think it would work).
3) Is there a way to utilize etherchannel or anything like this
A negative to option 2 would be that if 1 of the interfaces went down, all the sudden 2/3 (or so) of your traffic would be going through 1 router.
How to configure my serial modules on my 2600 and 3640? Each router has the WIC-2T with two cables connecting them. I tried to ping one router from the other, but no luck. Serial IP address I just made up, this is my home lab, so if I messed those up some how,
Here is the running config for each rotuer:
2610:
Current configuration : 1071 bytes
!
version 12.3
[Code]...
I have two routers at our core data center, a 3845 and a 3640. These are configured with GLBP. There are 4 remote sites:
Site #1: One T1 link to the 3825
Site #2: One T1 link to the 3825, and One T1 link to the 3640
Site #3: One T1 link to the 3825, and One T1 link to the 3640
Site #4: One fractional T1 link to the 3825, and One T1 link to the 3640.
My question regards site #4. If i understand correctly, GLBP works on the premise of "host" balancing, and not true "load" balancing. The reason I ask is that the large majority of our WAN traffic is from our Exchange server to our remote sites. In the case of site #4, our exchange server is sending traffic on the fractional T1. Is there any way with GLBP to either split this traffic from a particular host across two links in a round-robin fashion, but leave other hosts to travel wherever the router sends them, or, to force at least our exchange server to use the full T1, rather than the fractional?
I've read up on the weighting mechanism, and it appears that tracking an interface has nothing to do with bandwidth use. If I understand correctly, if I were to track the Site #4 PPP to the 3640, and give a weight of 10 to glbp on there, it would really only take affect if the interface is down. It will have nothing to do with host AVF election.For the record, exchange traffic is constant to this site, so there is no chance for the host connection to reset and potentially elect to use the larger pipe. I would like to "tweak" this to make better use of available bandwidth.
I am using ASA Version 8.2(1) , I want to limit the vpn users to use less bandwidth of my Interlink to access something on inside network
example : source vpn pool
Destn : inside network
how can achive this with QOS config.
i just came to know Assurance feature license doesn't come for free when upgrading from LMS4.2 or NCS1.1. It has to be purchased. Before buying this license, i would like to know if IPv6 netflow is supported.
View 0 Replies View RelatedI need to implement IPv6 for ASA VPN. According to the ASA_8.4_cli_cfg.pdf , IPv6 is not supported on ASA IPSEC vpn and remote client vpn. I do not have a ASA 8.4, any way to verify on ASA8.4 whether the crypto command support ipv6 address ? If the crypto command do support ipv6 address then probably there is chance it will work.what i mean is eg. crypto map xxx set peer <ipv6 address| ipv4 addres> able to set ipv6 address.
View 4 Replies View RelatedDoes cisco LMS v3.2 Support IPV6 in all modules ? We will be migrating from V4 to V6 in some time from now
View 1 Replies View RelatedAccording to the url below, i could find that there is a separate module required for asr 9k, is it so; doesnt it sufficient to have the 4.3.0 Ios-xr version for the cgnat supoort features of nat 44, nat64, ds-lite.. like things?URL
View 1 Replies View RelatedI would like to get it clarified, that Cisco WLC 2504 running the code ( 7.2.110.0 ) does support IPv6 or not ?
From Cisco Documents they are asking to enable IPv6 support under WLAN > Edit Page, and Enabling mulicast on Ethernet Multicast Mode under Controller > General.
But from the GUI am not able to find the above two field, Even in Interface i created under Controller > interface is not accepting IPv6 address. I am able to configure IPv6 ACL .
Is any deployment document is available to show different scenarios with configuration.
Note - Am using Access point AIR-LAP1262N-N-k9
Is there any IPv6 support planned or in the works for RV082?
View 3 Replies View RelatedI want to ask that does ASA 5580 support the nat-pt for IPv6?
View 2 Replies View Relatedwe have a Cisco 2851 router and bought the following IOS::
System image file is "flash:c2800nm-spservicesk9-mz.124-25d.bin"
Cisco IOS Software, 2800 Software (C2800NM-SPSERVICESK9-M), Version 12.4(25d), RELEASE SOFTWARE (fc1)
I thought this version was supposed to have IPv6 support?
TEST(config)#ipv6 unicast-routing ^% Invalid input detected at '^' marker.
TEST(config)#
which IOS should we buy?
how to add IPv6 support via HE's TunnelBroker to an RV016.
View 0 Replies View RelatedI've got older SOHO97 which I want to use as a backup for Cisco 800 but I can not find any information if it actually supports IPv6. Neither the data sheet [URL] nor the Cisco Feature Navigator [URL] suggest it has any IPv6 support at all.
View 1 Replies View RelatedI was slightly dissapointed with the performance of the "pre-sales" phone number of Cisco in the Netherlands so I am asking it here instead.We decided on using 2 Cisco 2921 routers with 2.5GB ram to use for a MultiHomed connection using BGP. We already have our v4 and v6 space assigned as well as our AS number. The connections should turn up soon.What I could not find out with proper certainty on the Cisco Feature Navigator is if the IP BASE on the Cisco 2921 supports both IPv4 and IPv6 routing combined with BGP. This model uses the Universal IOS licensing which I found slightly confusing. I could not find a simple matrix with the supported commands either.
View 1 Replies View RelatedBelow is my Topo
DUT------router(7600)------Sami module (slot 9)
I have both ipv4 and Ipv6 config on all the three hops. Between Cisco and Sami module, I have the Ip config on vlan interface 1400(say). Its not on a physical interface obviously, I can ping ipv5 from DUT to Sami IPv4 address. But Ipv6 doesnt work. If I add a sttic route to DUT network on SAMI, show ipv6 route does not show it.
i want ti migrade lan from ipv4 to ipv6.. how can i check my switch support ipv6?
i am having cisco 3500 and d-link managed and unmanaged switchs.
Does WAG120N Support IPv6 ?
View 1 Replies View RelatedWould like to see IPv6 support on the WAG320N. Some ISPs now support this protocol....should eventually become a standard feature.
View 1 Replies View RelatedI purchased a Latitude E6220 with a 4G WWAN modem (the DW5800). My intention was to support DirectAccess, i.e. Microsoft's clientless VPN, but unfortunately I have not found any way to get the IPv6 protocol installed on the device.
I've searched Verizon Wireless, Dell and Novatel Wireless forums without any success.
was told to allow Ipv6. Does my modem support this?
View 1 Replies View Related