Cisco Routers :: Getting IPv6 Support For RV082
Jan 27, 2010Is there any IPv6 support planned or in the works for RV082?
View 3 Replies
ADVERTISEMENT
Cisco Routers :: RV082 IPv6 Tunneling With 6to4
Apr 28, 2013I have several RV082 routers in production, most of them on IPv4-only access. I want to roll out IPv6 on all these networks and have set up a test environment for this.I did start with a factory-defaulted router with a fixed public IPv4 address. IPv4 network access does work as expected.With the 6to4 option disabled, the RV082's IPv6 routing table contains several entries for local addresses, but not public ones, as expected. When enabling the 6to4 transition function as described in SBKB article #567, three new entries are created: [code]
With the router's diagnostic ping function I can ping the next 6to4 relay on IPv4 (192.88.99.1) and IPv6 (2002:c058:6301::). But I cannot ping that next hop address given as default route (::c058:6301).The RV does advertise routes with the correct 6to4 prefix on the LAN side, and the clients connected to it configure themselves with appropriate addresses. However I was unable to ping any IPv6 both in the 2002::/16 as well as in the 2000::/15 range from any system on the RV's LAN side. When trying to add a static route which routes the 2000:: prefix with prefix length 15 to next hop 2002:c058:6301:: with metric 1, I keep getting the message "Please input IPv6 Address with correct format!"could there something wrong with this default route? How can it be changed? And what is the problem with the route I am trying to add?
Belkin Routers :: Does F5d8636-4v1 Support Ipv6
Feb 3, 2013was told to allow Ipv6. Does my modem support this?
View 1 Replies View RelatedCisco Routers :: How To Add IPv6 Support Via TunnelBroker To A RV016
Jun 21, 2012how to add IPv6 support via HE's TunnelBroker to an RV016.
View 0 Replies View RelatedReplace The RV082 With Something Gigabit And Supporting IPv6?
Feb 27, 2011I've had a Linksys RV082 for years and years and years. I've been trying to replace the aging thing for a while (with something gigabit and supporting IPv6). Unfortunately, I've really not found anything that comes close to having the features of the old RV. I've looked at NetGear, D-Link, and Cisco/Linksys, but everything seems to fall short (or just have bad reviews). This little RV082 came packed with a lot of features for a lower to mid level gateway.
View 1 Replies View RelatedCisco :: IPv6 Netflow Support On PI1.2?
Jan 9, 2013i just came to know Assurance feature license doesn't come for free when upgrading from LMS4.2 or NCS1.1. It has to be purchased. Before buying this license, i would like to know if IPv6 netflow is supported.
View 0 Replies View RelatedCisco VPN :: IPv6 Support On ASA 8.4 IPSEC
May 7, 2011I need to implement IPv6 for ASA VPN. According to the ASA_8.4_cli_cfg.pdf , IPv6 is not supported on ASA IPSEC vpn and remote client vpn. I do not have a ASA 8.4, any way to verify on ASA8.4 whether the crypto command support ipv6 address ? If the crypto command do support ipv6 address then probably there is chance it will work.what i mean is eg. crypto map xxx set peer <ipv6 address| ipv4 addres> able to set ipv6 address.
View 4 Replies View RelatedCisco :: Does LMS V3.2 Support IPV6 In All Modules
May 1, 2013Does cisco LMS v3.2 Support IPV6 in all modules ? We will be migrating from V4 to V6 in some time from now
View 1 Replies View RelatedCisco WAN :: IPv6 Support On ASR 9000
Jun 10, 2013According to the url below, i could find that there is a separate module required for asr 9k, is it so; doesnt it sufficient to have the 4.3.0 Ios-xr version for the cgnat supoort features of nat 44, nat64, ds-lite.. like things?URL
View 1 Replies View RelatedCisco Wireless :: IPv6 Support On WLC - 2504?
Aug 28, 2012I would like to get it clarified, that Cisco WLC 2504 running the code ( 7.2.110.0 ) does support IPv6 or not ?
From Cisco Documents they are asking to enable IPv6 support under WLAN > Edit Page, and Enabling mulicast on Ethernet Multicast Mode under Controller > General.
But from the GUI am not able to find the above two field, Even in Interface i created under Controller > interface is not accepting IPv6 address. I am able to configure IPv6 ACL .
Is any deployment document is available to show different scenarios with configuration.
Note - Am using Access point AIR-LAP1262N-N-k9
Cisco Firewall :: Does ASA 5580 Support NAT-PT For IPv6
Mar 29, 2011I want to ask that does ASA 5580 support the nat-pt for IPv6?
View 2 Replies View RelatedCisco Infrastructure :: 2851 - IPv6 Support In IOS
May 10, 2011we have a Cisco 2851 router and bought the following IOS::
System image file is "flash:c2800nm-spservicesk9-mz.124-25d.bin"
Cisco IOS Software, 2800 Software (C2800NM-SPSERVICESK9-M), Version 12.4(25d), RELEASE SOFTWARE (fc1)
I thought this version was supposed to have IPv6 support?
TEST(config)#ipv6 unicast-routing ^% Invalid input detected at '^' marker.
TEST(config)#
which IOS should we buy?
Cisco Switches :: SOHO97 / 800 - Unable To Support IPv6
Dec 7, 2010I've got older SOHO97 which I want to use as a backup for Cisco 800 but I can not find any information if it actually supports IPv6. Neither the data sheet [URL] nor the Cisco Feature Navigator [URL] suggest it has any IPv6 support at all.
View 1 Replies View RelatedCisco WAN :: 2921 ISR G2 Series BGP IPv6 Support Required
May 24, 2011I was slightly dissapointed with the performance of the "pre-sales" phone number of Cisco in the Netherlands so I am asking it here instead.We decided on using 2 Cisco 2921 routers with 2.5GB ram to use for a MultiHomed connection using BGP. We already have our v4 and v6 space assigned as well as our AS number. The connections should turn up soon.What I could not find out with proper certainty on the Cisco Feature Navigator is if the IP BASE on the Cisco 2921 supports both IPv4 and IPv6 routing combined with BGP. This model uses the Universal IOS licensing which I found slightly confusing. I could not find a simple matrix with the supported commands either.
View 1 Replies View RelatedCisco VPN :: Sami Module On 7600 IPv6 Support
Apr 3, 2013Below is my Topo
DUT------router(7600)------Sami module (slot 9)
I have both ipv4 and Ipv6 config on all the three hops. Between Cisco and Sami module, I have the Ip config on vlan interface 1400(say). Its not on a physical interface obviously, I can ping ipv5 from DUT to Sami IPv4 address. But Ipv6 doesnt work. If I add a sttic route to DUT network on SAMI, show ipv6 route does not show it.
Cisco WAN :: 3500 - How To Check Switches Support IPV6 In LAN
Feb 6, 2013i want ti migrade lan from ipv4 to ipv6.. how can i check my switch support ipv6?
i am having cisco 3500 and d-link managed and unmanaged switchs.
Linksys Cable / DSL :: Does WAG120N Support IPv6
Dec 16, 2011Does WAG120N Support IPv6 ?
View 1 Replies View RelatedLinksys Cable / DSL :: IPv6 Support For WAG320N?
Jul 7, 2011Would like to see IPv6 support on the WAG320N. Some ISPs now support this protocol....should eventually become a standard feature.
View 1 Replies View RelatedDell :: DW5800 4G LTE Card Does Not Support IPv6
Sep 1, 2011I purchased a Latitude E6220 with a 4G WWAN modem (the DW5800). My intention was to support DirectAccess, i.e. Microsoft's clientless VPN, but unfortunately I have not found any way to get the IPv6 protocol installed on the device.
I've searched Verizon Wireless, Dell and Novatel Wireless forums without any success.
Cisco WAN :: Does Nexus 7000 Support Ipv6 6to4 Tunnel
Nov 23, 2011Does Nexus 7000 support ipv6 6to4 tunnel?
View 3 Replies View RelatedCisco Switching/Routing :: 2960 And 4510 IPv6 Support
Mar 2, 2013I have cisco 2960 and Catlyst 4510 switches now we are planning to implement IPV6.
i have the fallowing IOS on my switches.
C2960-lanbasek9-mz.122-50.se5
Cat4500e-entservicesk9-mz.122-54.sg1.bin
The above ios will support for IPV6 or I have to purchase new IOS, which version will support.
Linksys Wireless Router :: E3000 Does Not Have IPv6 Support
Feb 23, 2011I know that the E3000 does not have IPv6 support. I wanted to know if it will get a firmware update to support it?
View 9 Replies View RelatedCisco Wireless :: Aironet 1100 / 1120 / 1130 Support For IPv6?
May 27, 2012I find much document, but not found information about whether those support for IPv6 e.g. dual-stack like newer series.
View 3 Replies View RelatedCisco AAA/Identity/Nac :: ACS 1113 Solution Engine / Version 4.2 Does It Support Ipv6
Aug 3, 2011I Have a requirement to migrate from ipv4 to ipv6, I have checked the scalability of all the devices for this migration except ACS 1113 Solution Engine, Version 4.2. I couldnt reach the proper documentation to check its support for ipv6.
View 1 Replies View RelatedCisco Switching/Routing :: Which Ios Will Support IPv6 Feature In WS-C3560G-48TS Switch
Feb 18, 2013I am having WS-C3560G-48TS switch with ios(c3560-ipbasek9-mz.122-58.E2.bin) and I am trying to use IPv6 feature in this switch model. More over I've upgraded this switch with many ios but none of them not supporting IPv6 feature. ios which supports IPv6 feature?
View 3 Replies View RelatedCisco Switching/Routing :: 3640 What IOS Version Can Support IPv6 RIP In Hardware Limit
Jun 25, 2012I have the cisco 3640 with IOS Version 12.2(46) , and it with DRAM:32M , Flash:8M.What IOS version can support IPv6 RIP in the hardware limit?
View 3 Replies View RelatedLinksys Wireless Router :: Firmware Upgrade For WRT120N To Support IPV6?
Jul 22, 2010IPV4 IP addresses will be running out in less than a year and I wanted to know, will there be a firmware update for WRT120N to support IPV6?
Also, if I have to buy another router to support IPV6, I'm going to buy a D-Link. It's nothing personal, I just find it absolutely idiotic that a router that supports wireless-N doesn't support IPV6. You have to ask your self, how does the standard IPV6 spec thats a few years old not make it to the final product of a router, but a non-standard wireless-N spec implementation somehow got the O.K....?
Linksys Wireless Router :: EA3500 Ethernet Ports Do Not Support Ipv6?
May 29, 2012Region : Ireland
Model : TL-MR3420
Hardware Version : V2
Firmware Version :
ISP :
I have my router updated with the latest firmware and I'm pretty sure all the settings are correct but I'm only getting a max transfer rate of 144Mbps. I know this because I use InSSIDer 3 to analyse my wifi network etc. I stream movies over my network and while DVD quality movies play fine, HD movies tend to freeze and buffer a lot. I have the router's channel width set to 40Mhz, so I know that's not the problem. Strangely, I also use a Netgear wifi extender with the MR3420 and it's max rate is 300Mbps.
Linksys Cable / DSL :: Does WAG160Nv2 Support IPv6 Addresses Primarily For Gateway IP
Feb 3, 2011Does WAG160Nv2 support IPv6 addresses primarily for the Gateway's IP and thereafter about all IPs that need to be entered via the web interface?
View 9 Replies View RelatedCisco Routers :: VPN Between Two RV082 Routers Not Working?
Aug 7, 2012We're getting the following message in the logs when we ry to connect: encrypted Informational Exchange message is invalid because it is for incomplete ISAKMP SA
One of the router is a V2 and the other is a V4 if that makes any difference.
Cisco Routers :: What About Ipv6 On Srp500 Series
Jun 4, 2012Tomorrow 2012-06-06 is ipv6 launch day, what about ipv6 on srp500 series ? On product specification cisco wrote : IPv6 (RFC 6204) ready.
View 10 Replies View RelatedCisco Routers :: LAN To LAN Routing RV082?
Jan 29, 2013We have an RV082 setup with WAN to the internet and LAN IP of 192.168.188.1.If I add a static route like so:
network: 192.168.166.0
mask: 255.255.255.0
gateway: 192.168.188.2
hop count: 1
interface: LAN
The device with IP 192.168.188.2 will be connected directly to one of the LAN ports on the router.Will that work to route, trying to get to 192.168.166.0 to the IP of 192.168.188.2?It just seems odd because the packets would hit the router then go back out through the LAN port.
Cisco Routers :: Rv082 Configure One-to-one Nat
Nov 17, 2011isco epc3925 in transparent bridge provided by isp with following wan details
ip=x.x.x.120 subnet=255.255.255.248 gw=x.x.x.121 and 2 dns server ip's
I can't get the one-to-one nat working. read in some forums that the rv082 can do the job.