Replace The RV082 With Something Gigabit And Supporting IPv6?
Feb 27, 2011
I've had a Linksys RV082 for years and years and years. I've been trying to replace the aging thing for a while (with something gigabit and supporting IPv6). Unfortunately, I've really not found anything that comes close to having the features of the old RV. I've looked at NetGear, D-Link, and Cisco/Linksys, but everything seems to fall short (or just have bad reviews). This little RV082 came packed with a lot of features for a lower to mid level gateway.
View 1 Replies
ADVERTISEMENT
Sep 13, 2011
I have an old RV082 with firmware version 2.0.0.19. I want to replace it with a new RV082 firmware version 4.0.2.08.I exported the fv2 config but can't restore it on the fv4. I get "invalid file type" error. The fv4 box is looking for a .config file and the fv2 box saves as a .exp file.
View 4 Replies
View Related
Oct 1, 2012
I have a linksys rv082 VPN router with 35-50 computers, 2 VPN connections, 4 servers. I wondering if replacing the linksys rv082 router with a cisco rv180 VPN router is a good idea. According to the rv180's specifications, it seems to be a good router, my concern is that it looks small in size in comparation with the linksys rv082. I wonder if the rv180 can handle the work and the trafic of my network. I would like to know if it is ok to replace it or what are the risks.
View 4 Replies
View Related
Jan 27, 2010
Is there any IPv6 support planned or in the works for RV082?
View 3 Replies
View Related
Apr 28, 2013
I have several RV082 routers in production, most of them on IPv4-only access. I want to roll out IPv6 on all these networks and have set up a test environment for this.I did start with a factory-defaulted router with a fixed public IPv4 address. IPv4 network access does work as expected.With the 6to4 option disabled, the RV082's IPv6 routing table contains several entries for local addresses, but not public ones, as expected. When enabling the 6to4 transition function as described in SBKB article #567, three new entries are created: [code]
With the router's diagnostic ping function I can ping the next 6to4 relay on IPv4 (192.88.99.1) and IPv6 (2002:c058:6301::). But I cannot ping that next hop address given as default route (::c058:6301).The RV does advertise routes with the correct 6to4 prefix on the LAN side, and the clients connected to it configure themselves with appropriate addresses. However I was unable to ping any IPv6 both in the 2002::/16 as well as in the 2000::/15 range from any system on the RV's LAN side. When trying to add a static route which routes the 2000:: prefix with prefix length 15 to next hop 2002:c058:6301:: with metric 1, I keep getting the message "Please input IPv6 Address with correct format!"could there something wrong with this default route? How can it be changed? And what is the problem with the route I am trying to add?
View 1 Replies
View Related
Sep 26, 2012
I have an Ethernet Loopback Plug (4 Pairs) made and trying to test the Gigabit Interface on a 3845 Router with a fail result. The interface will show up/up only if I set the interface to 100M/Full Duplex when I plug-in the Ethernet Loopback Plug (4 Pairs). I don't see this Gigabit Interface @ 3845 router has any option to set it to internal or external loopback.
View 2 Replies
View Related
Nov 23, 2011
I'm running an Optiplex 330 with the Broadcom NetXtreme 57xx Gigabit ethernet card.
The computer is running Windows 7, 64bit, but there do not appear to be any drivers for that OS.I tried selecting Vista 64bit, but there were no drivers. The Vista 32bit doesn't work.
Then I went to Broadcom and found these drivers: [URL] the W764bit drivers didn't change the fact i'm still on a 100Mbit card (as seen on Local Area Connection Status screen and the Device manager)
View 1 Replies
View Related
Aug 28, 2012
I just turned my computer IP address changed. I tried to get a uk ip address for accessing some information on internet. But my computer stopped supporting internet server to access it. I got some information from the [URL]... but unable still to find access.
View 3 Replies
View Related
Dec 18, 2010
I am trying to configure below commands in Cisco 4506 E with SUP 6 LE but these commands are not not supporting in the switch.Even QOS command is not taking in the siwtch....This was working fine in Cisco 4500 with SUP 2..not i upgared to 4506 E with Sup 6 LE.
qos dblqos map dscp 0 to tx-queue 2qos map dscp 16 18 20 22 24 26 28 30 to tx-queue 4qos map dscp 34 36 38 to tx-queue 4qos map cos 3 to dscp 26 qos map cos 5 to dscp 46 qos
View 1 Replies
View Related
Jun 25, 2012
Can 3600 series model AP work with WLC 4402 with existing license, we purchased 25 LIC pack and still using only 15. Any recommended Part no on 3600 series with external Antenna
View 5 Replies
View Related
Jul 15, 2012
We have a 7604 chassis with the following equipments:
1. RSP720-3C-10GE
2. 7600-SIP-400
3. SPA-1X10GE-L-V2
We would like our SPA to support XFP transceiver having part number XFP-10GZR-OC192LR.
View 2 Replies
View Related
Dec 5, 2012
I want to do qinq on this card under its sub-interface, unfortanately it doesnt support the command as compared to other ES cards. [code]
View 3 Replies
View Related
Jun 30, 2011
I have recently purchased ASR1002-RP1-ESP5 with 2 x 4K Broadband licenses to be used as LNS. Cisco have sent me PAK files for the licenses however when I try to enter the licenses into the device I get an error message saying that Licensing is not supported on this platform.
Any experience with this platform and installation of the broadband licenses?
When I spoke to Cisco TAC they told me that for this particular model the licensing is on "trust" basis where you buy license and do not install it on the actual router - similar to what 7200 used to do.
View 1 Replies
View Related
Jan 14, 2013
I know this is a small business appliance I got my ccna certification with the hope of practice my CLI skills with a cisco device however I read in cisco docs the small business routers doesn´t support talnet neiter ssh I mean CLI, is thta true ?
View 1 Replies
View Related
May 2, 2013
Cisco view(patch 6.1.9) in lms 3.2.1 is not supporting router 1905.
View 11 Replies
View Related
Sep 5, 2011
After extensive research, I am asking this question:Do you know of a SSL supporting, non active X reliant (does not require Internet Explorer) IP internet streamed camera? I am looking for a internet camera that can be encrypted using SSL, streamed over the internet, and accessed by clients running multiple operating systems and browsers.
View 3 Replies
View Related
Dec 15, 2012
Region : India
Model : TL-MR3040
Hardware Version : V1
Firmware Version : 3.14.2 Build 120822 Rel.40902n
ISP : Airtel
I have just bought the MR3040. I am using this in India with local ISP Airtel and ZTE MF 880T LTE modem, which normally gives 4G connection when connected directly to the laptop.I have used the normal settings as guided by TP link and checked that dialing properties are all fine. When I am connecting through the MR3040, the blue light is visible in the modem but there is NO internet throughput, the internet icon in the router also remains OFF.
View 3 Replies
View Related
Sep 9, 2012
How about supporting an scp server on the switch? Makes life much easier for collecting configs and pushing OS upgrades.
View 1 Replies
View Related
Dec 7, 2011
It seem that ACE10 not support 12.2(33)SXJ1 IOS running on C6500. The box cannot detect the ACE module when power up. Currently the ACE10 running on system A2(30).
My challenge i have the ASA SM that compulsary to run on 12.2 (33) SXJ1 version. How to let these 2 module can running on the same C6500 box?
View 1 Replies
View Related
Jul 27, 2011
I have a wireless linksys E1000 in my n/w. In the manual I could see that i can support VPN connections. I want to know what VPN client is supported. I have configured the router using only the web interface and i didnt want to use Cisco Connect. Is it mandatory to use Cisco Connect for VPN access , as this would lead to changing my network settings.
View 4 Replies
View Related
Dec 29, 2011
I just purchased a new E4200 router. When I try to set it up, , it says that my software (Lion v. 10.7.2) is unsupported. Is there a download that will allow me to use this router?
View 2 Replies
View Related
Aug 13, 2012
Our current cable ISP is having issues providing us with consistant connectivity. I would like to bring in a second ISP to allow my users to choose where they will connect to. There will be two dns names and i just want to to be able to choose between them.
Is this possible on the ASA5505? supporting two ISPs at one time for VPN on both?
View 3 Replies
View Related
Jan 7, 2012
The model WS-C3750X-24T-L is only Lan Base. We need this switch to use EIGRP Protocol. Does it exist a License for supportting IP Base o IP Services Feature Set?
View 4 Replies
View Related
Sep 4, 2012
Can mac address replace ip (yes or no)
View 1 Replies
View Related
Feb 10, 2012
Can I replace my AT&T 2 Wire with any DSL Modem? We get terrible wireless response in rooms not close to the modem, I don't care what the additional cost is, I just want to use my laptop throughout the house, including my basement.
View 4 Replies
View Related
Mar 6, 2013
I am attempting to replace an existing printer on the network and keep running into trouble. I am sure at this point it is my frustration with it that is not allowing me to see what I am doing wrong. I attempt to just swap it out with exsiting printer and it grabs an IP address and then when I try to enter that IP address into my broswer to access the printer to give it the permanent one from printer I am replacing I cannot get to the printer.
View 6 Replies
View Related
Nov 9, 2012
My home router is an aging D-Link DGL-4100 and I am looking to replace it.My max budget is ~$250 USD.
I use 2 Ubiquiti Unifi UAP-Pro APs in my home for WIFI access, so I have the WIFI aspect of my home network covered completely. All wiring in my home is either Cat5e or Cat6, my switch is a gigabit HP ProCurve 1810G-24, and my cable modem is a Motorola SB6120 (Comcast cable broadband). I have 7 IP cameras (security system), 4 streaming media players, several PCs, a server, and several other network connected devices. I am the only resident.
I am looking to maximize my WAN to LAN (& LAN to WAN) throughput while maintaining a very secure network. I also want the router to have reliable VPN. If it is a wireless router, I would most likely not utilize the WIFI feature, probably turning off the WIFI radios and just use the router functionality.
I don't have the time/patience to build a PFSense (or similar) box and learn the software, so am only considering an off-the-shelf solution. Yes I know that PFSense and Untangle are great, I simply don't have time to learn them presently or in the foreseeable future.So, which router for wired performance and security would you recommend?
View 2 Replies
View Related
May 14, 2011
I have a small network (10 computers) with 1 SBS 2003 domain controller.There are 3 cables plugged into the Cisco PIX...
>One ethernet cable to our switch
>One console cable plugged into our server
>And of course the power cable
I need to , but I noticed something I've never seen before.... When I unplug the CONSOLE cable our Internet shuts off.I would expect that of the ethernet cable, but not of a console cable.I'm an experienced network tech, but not a Cisco guy. Am I missing something? Is this type setup typical of a Pix?
View 3 Replies
View Related
Nov 15, 2012
I had an issue yesterday with no internet access on my desktop computer; the message said "Network cable unplugged" so I called AT&T tech support for assistance. I have 2 Dell computers; a desktop and a laptop which I use wirelessly in the house.After doing several things from disconnecting the router to try and determine if the problem was with my router or an ethernet cable AT&T determined a port on my router which is 6 years old could be going bad and recommended I replace my router.I contacted Linksys yesterday; spoke to tech support for my WRT54G router and was given 2 model recommendations. One was a Model E900 N300 and a more expensive model; an EA2700 N600. There is a price difference of $40.00 USD between the 2 models. I could probably get by with the E900 N300 for $49.99 but the guy at Linksys was putting the pressure on me to buy the more expensive one for $89.99. I told him I'd have to think about it.
View 5 Replies
View Related
Feb 17, 2012
I have a HP DV6000 Laptop. The wireless coverage is not very good and I was thinking of upgrading the Wireless card to something better. The current card is HP Pavilion DV9000 PCI-Express Wireless WIFI Card 802.11a/b/g 441075-001 by HP. Is it even possible to install another card in the laptop or does HP limit what you can put in this laptop
View 3 Replies
View Related
Sep 26, 2011
can you replace the standard wired modem provided by your ISP with a wireless/wifi modem yourself?
View 4 Replies
View Related
Nov 12, 2011
How to replace fan incisco 2811 router in live or down condition?
View 2 Replies
View Related
Jun 23, 2012
I think that my rommon image has become corrupt as it will not take a new IOS image. I have tried several images that are within the recommended size and work with another 2620 with exactly the same specification also some commands that are available are not recognised when typed
View 7 Replies
View Related
