Can Mac Address Replace Ip
Sep 4, 2012Can mac address replace ip (yes or no)
View 1 Replies
ADVERTISEMENT
Can Replace AT&T 2 Wire With Any DSL Mode
Feb 10, 2012Can I replace my AT&T 2 Wire with any DSL Modem? We get terrible wireless response in rooms not close to the modem, I don't care what the additional cost is, I just want to use my laptop throughout the house, including my basement.
View 4 Replies View RelatedHow To Replace A Network Printer
Mar 6, 2013I am attempting to replace an existing printer on the network and keep running into trouble. I am sure at this point it is my frustration with it that is not allowing me to see what I am doing wrong. I attempt to just swap it out with exsiting printer and it grabs an IP address and then when I try to enter that IP address into my broswer to access the printer to give it the permanent one from printer I am replacing I cannot get to the printer.
View 6 Replies View RelatedReplace DGL-4100 With Which Router?
Nov 9, 2012My home router is an aging D-Link DGL-4100 and I am looking to replace it.My max budget is ~$250 USD.
I use 2 Ubiquiti Unifi UAP-Pro APs in my home for WIFI access, so I have the WIFI aspect of my home network covered completely. All wiring in my home is either Cat5e or Cat6, my switch is a gigabit HP ProCurve 1810G-24, and my cable modem is a Motorola SB6120 (Comcast cable broadband). I have 7 IP cameras (security system), 4 streaming media players, several PCs, a server, and several other network connected devices. I am the only resident.
I am looking to maximize my WAN to LAN (& LAN to WAN) throughput while maintaining a very secure network. I also want the router to have reliable VPN. If it is a wireless router, I would most likely not utilize the WIFI feature, probably turning off the WIFI radios and just use the router functionality.
I don't have the time/patience to build a PFSense (or similar) box and learn the software, so am only considering an off-the-shelf solution. Yes I know that PFSense and Untangle are great, I simply don't have time to learn them presently or in the foreseeable future.So, which router for wired performance and security would you recommend?
Protocols / Routing - Replace The Cisco Pix?
May 14, 2011I have a small network (10 computers) with 1 SBS 2003 domain controller.There are 3 cables plugged into the Cisco PIX...
>One ethernet cable to our switch
>One console cable plugged into our server
>And of course the power cable
I need to , but I noticed something I've never seen before.... When I unplug the CONSOLE cable our Internet shuts off.I would expect that of the ethernet cable, but not of a console cable.I'm an experienced network tech, but not a Cisco guy. Am I missing something? Is this type setup typical of a Pix?
Replace Linksys WRT54G Router
Nov 15, 2012I had an issue yesterday with no internet access on my desktop computer; the message said "Network cable unplugged" so I called AT&T tech support for assistance. I have 2 Dell computers; a desktop and a laptop which I use wirelessly in the house.After doing several things from disconnecting the router to try and determine if the problem was with my router or an ethernet cable AT&T determined a port on my router which is 6 years old could be going bad and recommended I replace my router.I contacted Linksys yesterday; spoke to tech support for my WRT54G router and was given 2 model recommendations. One was a Model E900 N300 and a more expensive model; an EA2700 N600. There is a price difference of $40.00 USD between the 2 models. I could probably get by with the E900 N300 for $49.99 but the guy at Linksys was putting the pressure on me to buy the more expensive one for $89.99. I told him I'd have to think about it.
View 5 Replies View RelatedReplace A Wireless Card In My HP DV6000?
Feb 17, 2012I have a HP DV6000 Laptop. The wireless coverage is not very good and I was thinking of upgrading the Wireless card to something better. The current card is HP Pavilion DV9000 PCI-Express Wireless WIFI Card 802.11a/b/g 441075-001 by HP. Is it even possible to install another card in the laptop or does HP limit what you can put in this laptop
View 3 Replies View RelatedReplace Standard Modem With Wireless?
Sep 26, 2011can you replace the standard wired modem provided by your ISP with a wireless/wifi modem yourself?
View 4 Replies View RelatedCisco WAN :: How To Replace Fan In 2811 Router
Nov 12, 2011How to replace fan incisco 2811 router in live or down condition?
View 2 Replies View RelatedCisco WAN :: How To Replace ROMmon On 2620
Jun 23, 2012I think that my rommon image has become corrupt as it will not take a new IOS image. I have tried several images that are within the recommended size and work with another 2620 with exactly the same specification also some commands that are available are not recognised when typed
View 7 Replies View RelatedCisco WAN :: 837 - Replace Dialer 1 Interface With IRB?
Jun 21, 2011I have an 837 ADSL router that the customer is upgrading from a 3 meg circuit to a 10 meg circuit.
The previous vendor used PPOE for connection and we used a dialer 1 interface to make the connection with a user name and password.
The new connection is a straight WAN DHCP no username or password needed.
I realize I can change the dialer interface from negotiate to DHCP but do I still need it ?
Can I replace the dialer 1 interface with IRB ? Should i just keep the Dialer 1 interface since the device is currently set that way and just remove the PPP negotiation from dialer 1 ?
Cisco WAN :: MGX 8850 PXM-HD To Replace With Faulty HDD
Feb 3, 2011I have MGX 8850 (PXM45/AXSM) and I want replace My faulty hard disk 40Gbps (4200RPM) whith other hard disk 80Gbps (5200RPM).Is it possible or No?
View 1 Replies View RelatedReplace Adc Server In Windows 2003 Domain?
Jun 22, 2012Need to rebuild the server in different hardware.Replace adc server in windows 2003 domain
View 1 Replies View RelatedSystem Restore Failed To Replace The File
Jan 4, 2012After unable to connect to my wireless network, I did a restore - but got a message: System restore failed to replace the file (C:WindowsServiceProfilesLocalServiceAppDataRoamingPeerNetworking98c An unspecified error occurred during System Restore (0x80070002)I've tried 3 restores to get the same message.Am at a loss to get the computer back on line.Running win7 (32Bit) with Norton 360.
View 9 Replies View RelatedReplace The RV082 With Something Gigabit And Supporting IPv6?
Feb 27, 2011I've had a Linksys RV082 for years and years and years. I've been trying to replace the aging thing for a while (with something gigabit and supporting IPv6). Unfortunately, I've really not found anything that comes close to having the features of the old RV. I've looked at NetGear, D-Link, and Cisco/Linksys, but everything seems to fall short (or just have bad reviews). This little RV082 came packed with a lot of features for a lower to mid level gateway.
View 1 Replies View RelatedLinksys WRT54G: Want To Replace It With Upgraded Version
Jul 19, 2011I have an older router, Linksys WRT54G, how crappy is this?. How much better speed/connection can I get from a new router? . If you have any suggestions for routers under $100 that would be a big upgrade from this please post it.
View 3 Replies View RelatedCisco Firewall :: ASA 8.4 - New Configuration To Replace Old NAT 0 Command
Jan 15, 2012What is the new configuration in ASA 8.4 to replace the old "nat 0" command.
View 1 Replies View RelatedCisco WAN :: Replace Our 3825 Screening Router
Mar 25, 2012We use a 3825 router to screen alot of the junk from the internet side or our firewall. Its worked well for the last 4 years buthas rebooted multiple times in the last month for no apparent reason.At this point I think I would prefer to replace it.Our current internet link is 100Mbps and this router handles that quite well. Is there an equivalent that I should replace it with, or should I just buy another 3825 ?One with an OOB management port would be nice.
View 6 Replies View RelatedCisco WAN :: Need To Replace Router 831 With High End Model
Jul 19, 2011Our one of the Client need to replace CISCO 831 router with high end router , there will be around 60 to 70 users accessing this router for Internet surfing. Right now 831 having 3 Ethernet and 4 Fast Ethernet Ports.
View 4 Replies View RelatedCisco Firewall :: Upgrade / Replace 515E With ASA
May 15, 2012I need to upgrade/ replace a Cisco 515 E firewall with a Cisco ASA. Not sure what model yet! The pix has about 80 lines of ACLs and I side and outside interfaces with No VPNs.. I was wondering of those lines of ACLs can be transferred over to ASA as is or there are things I need to watch for ?
View 21 Replies View RelatedCisco VPN :: Pix 515E - Replace With Another 3845 Router?
Nov 18, 2011in my lab environment, I have a site-to-site VPN between a Pix515E and Cisco 3845 router, using AES-256/DH-5/SHA for isakmp and AES-256/SHA/PFS group5 for the site-to-site VPN, I can only push about 26Mbps IPSec traffics (tested with Iperf). CPU on the Pix515E is running at 96% utilization
Now if I replace the Pix515E with another Cisco 3845 router, I can push about 100bps. Why such a big difference between the data sheet and actual real world
[code]...
Cisco Routers :: 800 - Replace Access Points
May 22, 2013We have the following connection based in the services provided by our local telephone company, the connection arrives to a router Cisco 800 series. From the router, i send it connection to a switch SRW2024 v1.2 (Business series) 24-Port 10/100/1000 Gigabit Switch with webview. That switch is useful to send connection via RJ45 for a few of PCs. Then, I send connection to a switch SRW2008P (Business series) 8-port 10/100/1000 Gigabits with vieweb and power over ethernet. The last switch, send the signal via RJ45 to seven WAP2000 (business series) Wireless-G AP with PoE.
That network is running fine, but I've some problems to cover some areas within the building and sometimes the signal is really poor. The cable RJ45 between the PoE switch and each AP is no longer than 50 meters and each one with antennes about 8 or 9 Db.
So, now I've the possibility to change the access point for a power devices.
Cisco Firewall :: Replace Zywall With 5520 ASA
Jun 24, 2012i have to replace our zywall with an 5520 asa. [ode]
-connections from inside out outside, inside to dmz and inside to wlan.
-connections from wlan to outside, wlan to dmz
-connections from dmz to outside
connection from outside to dmz only for port 25,110,143,80,443,22 on ip 82.218.135.3.connections from outside 82.218.6.10:3389 to ip 10.1.0.200:3389. [code]
Home Network :: ISP Bandwidth Throttling - How To Replace Modem
Sep 29, 2012I think that my ISP is throttling my bandwidth at the modem . how access full available bandwidth.When the technician installed the fibre optic line and then the modem, he showed me an amazing 77MB/s (about 600Mbps) before the modem!!But after the technician left these were the test results after the router:
1) SpeedTests.net:
averages, after router, show: UP between 56/60Mbps & DN 45/75Mbps
2)Local Server Speed Test:
average: UP 45Mpbs & DN 170Mbps
A Japanese Internet savvy guy explained that NTT East throttles the available bandwidth at the building by specific apartment/modem settings related to individual contract bundles. I signed up for the top bundle: TV, Phone and Internet connections.This is my Hardware/ software setup:
OS: Win7,
Line specs:
Line type: IEC60874-14
Connector type: SC
Core across: 9 micrometers
Clad across: 125 micrometers
ITU-TG-652
NTT East fibreoptic TV/Internet/Telephone bundle (100Mbps best effort) Hikari Next Family Type but 10Mbps is considered within parameters
Asahi ISP Internet contract
Modem:
GE-PON (WAN+Coaxial TV antenna)
"SCM-GE-PON-<H>A GV-ONU D<1>" model
Router:
RT-S300HI (4 Giga ports + 1 phone)
Router & Modem have Japanese firmware which I cannot understand and, according to the NTT East, I must rent both modem and router from them and "will not support any other modem/router setup".I could not understand if it was because of technical or contractual limits.
I have tried to test my throughput after the modem but I could not figure out where the DNS, IP, WAN etc strings of numbers should go and, in the end, I simply cannot connect to the internet from my laptop directly to the modem so I cannot perform the same speed tests after the modem.
Replace Speedtouch 330 Modem With Netgear Router Dgnd3700?
Dec 16, 2012install a new N600 Wireless Dual Band Gigabit ADSL2+ Modem Router - Model DGND3700, to replace a Thompson Speedtouch USB Modem.
PC Windows XP Home Premium Media addition - Main PC X2 Laptops Win7 & Vista - fully working on wireless no issues.
I have managed to get two laptops working wirelessly with no problems, my main problem is the master pc needs to be able to use this router as well, but I cannot get it to work via the Ethernet cable!! I can get to to the Routers config page, I have done the following:
unplugged and removed the speedtouch modem, the old dial up connection is still available on the pc along with the speedtouch software and driver, I left this in place just in case the pc needs to revert back to the speedtouch modem, if I am unable to resolve this issue.
I have set the ip address on the PC to static and input the relavent Subnet and Gateway I can ping the Routers address 192.168.0.1 even though I have reserved the PC's Mac address and IP Adress I am unable to get to the internet. I have tried setting up a new internet connection via windows wizard.
when i look into the nework connections section in windows the local area connection is 100mb and there seems to be another connection which looks like another internet connection this indicates I am connected however I still cannot get an actual google session running.
Cisco :: Setting Up PIX506E To Replace Netscreen NS5GT
Jul 21, 2012I am new on CISCO but learning. I need to allowing ping from inside interface to outside interface. I need to allow SSH from outside to PIX506E and one node on inside 192.168.66.x. I also need to setup 32 public IP adresses to route inside nodes. I also need converting the rules from Netscreen firewall to PIX506E. Last, getting PDM working when i connect it start two windows but does not get PDM so i can configurate it thru PDM. [code]
View 2 Replies View RelatedCisco WAN :: Small Business To Replace Our Netgear DGN-3500
Jul 12, 2011I have recently purchased a Cisco 887w router for my small business to replace our Netgear DGN-3500. We have made the change to allow greater access to our internal IT infrastructure from remote locations. For the most part I have been able to work through the configuration but I have reached a point now where I can go no further. The WLAN, LAN and WAN all seem to be working well together as a basic setup but I cannot get any port forwarding/NAT to work.
So far I have attempted to configure two NATd services, both with the same result. I am trying to direct port 80 through to our web server, and port 444 to our VPN server. Both seem to undergo translation ok (if i am reading ip nat trans output correctly) but then the packets disappear. The VPN client annouces that the connection timed out, and the browser goes nowhere. Also, if i use an online port check it tells me that 80 and 444 are closed, with no packets returned.
I have spent a few days with no progress. The output of the log (attached txt file) might be meaningfull to somone with a stronger background with Cisco routers... I have also included the config and some other output that might be useful.
Cisco Application :: 8009 L7 Ace Configuration Replace Apache AJP
Jun 26, 2012i am trying to use teh ACE to replace an apache based load balancer in an jboss application cluster. I am using L7 loadbalancing to load balance between multiple components. the way these jboss application servers work with apache is that.When the jboss application starts up on the on application cluster, it issues a GET opencase/webservices/config-service?wsdl to the loadbalancer IP.The apache based LB in turn talks to the same box on port 8009 via ajp retrieves the configuration file and provides it back to the application on port 80.And after 2 has completed the Jboss application comes up. Basically to start the application the Apache loadbalacer will accept requests from the its target list and load balance the request back to them itself.Not sure how i can use the ACE to accomplish this. attached are my topology (logical) and the ace configuration. from my topology file -- the net-cms-1 will issue a get request to teh VIP (on the ace), the ACE accepts the connection but soon resets it.
View 1 Replies View RelatedCisco Wireless :: Replace 352 Bridged Network With 1552s?
Mar 20, 2012I have a question concerning replacing a 352 bridged network with 1552 mesh access points. Theoretically, imagine a centralized 352 with an omnidirectional antenna that is linked to multiple 352's with yagi antennas in a hub-spoke fashion. If this central 352 is replaced with a 1552 access point, will the existing Yagi's be able to talk to the 1552? I understand that the Yagi's AP's should be replaced with 1552's as well (thus forming a mesh network as the 1552s are designed to do) but for the sake of theory please assume the 'spoke' 352s will not be replaced. I have the understanding that the 1552s communicate over the 802.11a for the backhaul so I'm thinking this would cause some issues with the 352's.
View 2 Replies View RelatedCisco Routers :: Replace RV082 Firmware Version 2.0.0.19 With New 4.0.2.08
Sep 13, 2011I have an old RV082 with firmware version 2.0.0.19. I want to replace it with a new RV082 firmware version 4.0.2.08.I exported the fv2 config but can't restore it on the fv4. I get "invalid file type" error. The fv4 box is looking for a .config file and the fv2 box saves as a .exp file.
View 4 Replies View RelatedCisco Firewall :: To Replace Sonicwall NSA240 In SME Environment?
Oct 17, 2011I am looking for a Cisco firewall to replace a Sonicwall NSA240 firewall in SME environment?
View 3 Replies View RelatedCisco WAN :: Replace A ASA 5505 With 2801 With Security Bundle
Dec 21, 2011I'm trying to replace a ASA 5505 with a Cisco 2801 w/ security bundle.I have gone through a pretty basic set up of configuring what I could and letting the Cisco Config Prof do the security audit to lock it down. I have everything working just fine except for the bandwidth.
As soon as I plug the router in it seems to give all the bandwidth to one computer and the rest of the campus slows down to a crawl.I turned on "fair-queue" and even tried the QoS wizard in CCP, but it seems like thats if you want to prioritize voice over data - which we aren't running VOIP so I don't need.
Cisco WAN :: Replace 2611 Functionality With 3750G -48TS-S?
Aug 15, 2011We have an aging 2611 router that that we need to replace due to the fact that its 10Mb/s Ethernet ports are limiting our internet connectivity throughput (we have a 20Mb/s circuit).
The purpose of the 2611 router was to route traffic from multiple devices connected to a 2950 switch's VLAN X to the internet. Can we achieve this same functionality with only a 3750C-48TS-S switch? Could a static route statement on the 3750 replace the need for the router?