Cisco Firewall :: ASA 8.4 - New Configuration To Replace Old NAT 0 Command
Jan 15, 2012What is the new configuration in ASA 8.4 to replace the old "nat 0" command.
View 1 Replies
ADVERTISEMENT
Cisco Application :: 8009 L7 Ace Configuration Replace Apache AJP
Jun 26, 2012i am trying to use teh ACE to replace an apache based load balancer in an jboss application cluster. I am using L7 loadbalancing to load balance between multiple components. the way these jboss application servers work with apache is that.When the jboss application starts up on the on application cluster, it issues a GET opencase/webservices/config-service?wsdl to the loadbalancer IP.The apache based LB in turn talks to the same box on port 8009 via ajp retrieves the configuration file and provides it back to the application on port 80.And after 2 has completed the Jboss application comes up. Basically to start the application the Apache loadbalacer will accept requests from the its target list and load balance the request back to them itself.Not sure how i can use the ACE to accomplish this. attached are my topology (logical) and the ace configuration. from my topology file -- the net-cms-1 will issue a get request to teh VIP (on the ace), the ACE accepts the connection but soon resets it.
View 1 Replies View RelatedCisco Firewall :: Firewall / Can ASR 1006 Replace ASA 5580
Oct 30, 2011i check ASR 1006 config with ESP-40, the firewall permonce can reach 40G, ASA 5580 is 20G, can ASR 1006 replace ASA 5580, is there any function feature problem?
View 1 Replies View RelatedCisco Firewall :: Upgrade / Replace 515E With ASA
May 15, 2012I need to upgrade/ replace a Cisco 515 E firewall with a Cisco ASA. Not sure what model yet! The pix has about 80 lines of ACLs and I side and outside interfaces with No VPNs.. I was wondering of those lines of ACLs can be transferred over to ASA as is or there are things I need to watch for ?
View 21 Replies View RelatedCisco Firewall :: Replace Zywall With 5520 ASA
Jun 24, 2012i have to replace our zywall with an 5520 asa. [ode]
-connections from inside out outside, inside to dmz and inside to wlan.
-connections from wlan to outside, wlan to dmz
-connections from dmz to outside
connection from outside to dmz only for port 25,110,143,80,443,22 on ip 82.218.135.3.connections from outside 82.218.6.10:3389 to ip 10.1.0.200:3389. [code]
Cisco Firewall :: To Replace Sonicwall NSA240 In SME Environment?
Oct 17, 2011I am looking for a Cisco firewall to replace a Sonicwall NSA240 firewall in SME environment?
View 3 Replies View RelatedCisco Switching/Routing :: 1921 To Replace A Software Firewall
Feb 26, 2013We purchased a cisco 1921 router to replace a software firwall not long ago. The router was sold as a firewall with the suggestion that an ASA would be unnecessary.Unfortunately a router does not replace/do the jobs a firewall does, so I looked online and noticed that Cisco do offer firweall security features in one of their IOS.How do I tell if this is implemented on my router?If not, does my IOS support this, or do I need to buy an extension/another version of the IOS?,The version of the IOS I have is: c1900-universalk9-mz.SPA.151-4.M4.bin.
View 3 Replies View RelatedIP Configuration Command Won't Show WAN IP
Apr 16, 2011i have ADSL. modem:Meganet when i connect to internet from windows xp with making PPPOE connection everything is fine and when i do ipconfig i can see my IP. but when i connect directly from router then IPconfig show this only:
[code]...
Cisco Firewall :: 5520 - Procedure To Replace Failed Secondary ASA Unit
Apr 10, 2012i just received a RMA for failed ASA 5520 that was acting as secondary unit in multicontext configuration. What would be correct procedure to install it back in production? Do i need to restore backed up config of the fallen unit or is it just enough to enable multimode and connect to existing (primary) unit? Any good link for documentation that deal with this issues.
View 5 Replies View RelatedCisco :: Command To Show Entire Configuration?
May 16, 2011Is there a command that can show EVERYTHING that is configured on a router or switchSeems if you're looking to save enough information to completely swap out a device the run/start config isn't enough.Settings like VTP and MTU settings aren't shown in the config file ... there may be other configuration settings like thisAm I forced to just know to check those settings are is there a command that will show the running-config AND all these other settings that aren't in the config?
View 8 Replies View RelatedCisco Wireless :: Missing Configuration Command In CLI (1140 AP)
Jun 16, 2012I am trying to chang IP configuraton for my Cisco 1140 AP, but in CLI I dont have a "config" command (i used en before to enable administrative mode)
Bellow are the commands I can see:
AP7081.0506.d54a#?
Exec commands:
cd Change current directory
[Code].....
Cisco VPN :: 3000 - How To Get Running Configuration Through Command Line
Jul 13, 2011command to get running config of Cisco VPN 3000 concentrator.
View 3 Replies View RelatedCisco Switches :: SG300 - 10 Lcli Command / Local Configuration
Aug 25, 2011Previously srw2008 switches are used, now Cisco sg300-10 models was obtained. It does not work with ctrl-Z command to enter the local Config (lcli). What is the correct command?
View 2 Replies View RelatedCisco WAN :: 3560 Is There Some Wrong Configuration With Load-balance Command
Jan 28, 2013I have been experiencing some issue with a portchannel interface.I have two cisco switches 3560 and I have a portchannel between them ( It is composed by two gigabitethernet interfaces generating a portchannel of 2 Gigas ).Unfortunately, I am verifying that one interface traffics about 893MB but the other interface only traffics about 100MB.Is there any cause why is this happening? I thought that maybe both interfaces would traffic about 450MB.Is there some wrong configuration with the load-balance command?. At this moment there is no load-balance, It is only configured the port channel with the default configuration.
View 5 Replies View RelatedCisco VPN :: Missing Client Configuration Group Command - Old 2600 Router
May 9, 2012I need to create a Cisco VPN Client connection: I am following the cisco vpn client link and I don't have the command crypto isakmep client configuration group XXXXX
[URL]
This is what I get: crypto isakmp client configuration ? address-pool Set network address for client
This is my show version, if there is an IOS that will work:
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IK9S-M), Version 12.2(17a), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2003 by cisco Systems, Inc.
[Code].....
Cisco Switching/Routing :: 3400-ME No Boot System Command Available In Configuration
Feb 25, 2013I have a Cisco switch 3400-ME, it's running IOS1.bin file. Now i want to change the running IOS to IOS0.bin.I entered 2 commands:
boot system flash:dir1/IOS0.bin
boot system flash:dir1/IOS1.bin
But when i show running config, it has no any boot system commands. when i relboot that switch?
Cisco Switching/Routing :: Cat2960 - Save Configuration By Write Memory Command
Aug 22, 2012I got trouble when tried to save configuration by 'write memory' command.
cisco WS-C2960-48PST-L (PowerPC405) processor (revision G0) with 65536K bytes of memory. Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 12.2(52)SE,RELEASE SOFTWARE (fc3)
Cat2960#wr
Building configuration...
% Warning: Saving this config to nvram may corrupt any network management or security files stored at the end of nvram.
Continue? [no]: no % Configuration buffer full, can't add command:
After this message continue typing "yes" sometime that switch reload all times. The service compress-config command is not available anymore.
Cisco Switching/Routing :: Nexus 7010 - Command For Restoring The Running Configuration
Apr 29, 2012What is the exact command in restoring the running-config on a Nexus 7010. Is it the same command / procedure as the Cisco IOS?
View 3 Replies View RelatedCisco Switching/Routing :: Radius Server Command Missing From Global Configuration Mode 4510R
Feb 22, 2013I came across an interesting issue and thought I would see if anyone else has encountered it before contacting TAC.I have two Cisco Catalyst WS-4510R-E switches with a single Supervisor V module in each chassis. Both Sup cards are now running 12.2(54) SG1; ipbasek9 firmware; yes, I plan to move both switches to 15 code but that's another story. Anyways, prior to the upgrade the one switch was running 12.2 (33) code; I suspect the code was never upgraded; running ipbase non - K9 code. The other switch was running 12.2(44) with K9 prior to upgrade to 12.2(54).
View 2 Replies View RelatedCisco Switching/Routing :: Radius Server Command Missing From Global Configuration Mode 4510R-E
Apr 23, 2012I have two Cisco Catalyst WS-4510R-E switches with a single Supervisor V module in each chassis. Both Sup cards are now running 12.2(54) SG1; ipbasek9 firmware; yes, I plan to move both switches to 15 code but that's another story. Anyways, prior to the upgrade the one switch was running 12.2 (33) code; I suspect the code was never upgraded; running ipbase non - K9 code. The other switch was running 12.2(44) with K9 prior to upgrade to 12.2(54). With the background set, one switch reports the following:SwitchA (config)#r?radius-server redundancy regexp represourc rmon route-map router.
View 4 Replies View RelatedCisco Firewall :: NAT Command Conversion PIX 6.3 To ASA 8.4(2)
Dec 28, 2011I am in the process of migrating a production firewall from PIX 6.3 to ASA 8.4(2). This is going to be a complete firewall rebuild and I will not be upgrading the configs because they have become out of date and very bloated. I am in the process of converting the NAT commands.[code] I am hoping these commands would be enough to replicate the previous functionality. I removed all the static identity NATs because NAT control is no longer in place so those rules are not required. Additionally I didn't re-create the rules that had NAT ID 0 or 1 because it didn't look like they were doing anything. correct way to do the static NAT commands at the bottom.
View 3 Replies View RelatedCisco Firewall :: ASA 8.4 NAT Command Selection
Jul 4, 2011I am designing a new NAT configuration for an ASA 8.4
On my PIX 8.0 configuration I needed to allow bidirectional traffic between interfaces with different security levels. For example, Inside at 100 and dmz at 50.To accomplish this in 8.0 I used a static NAT command along with any necessary ACLs.
I now need to apply this same 8.0 config for 8.4. With the static command not availablein 8.4 I am unsure of which NAT commands to use to achieve the bidirectional traffic.
Cisco Firewall :: What New Command Is For NAT In Version 8.3
May 29, 2013what the new command is for NAT in version 8.3?The config i have is from Version 7.2 and doesnt work on 8.3. [code]
View 12 Replies View RelatedCisco Firewall :: 5505 - Command Changes From 7.2 To 8.6
Mar 10, 2013I'm coming from a 5505/5510 ASA to a 5512x. I see the following 7.2 commands are now set with the NAT command in 8.6:
-------------begin 7.2 commands---------------------
global (outside) 1 interfaceglobal (inside) 10 interfaceglobal (wireless) 1 interfacenat (inside) 0 access-list nonatnat (inside) 1 192.168.3.0 255.255.255.0static (inside,outside) tcp interface www 192.168.3.114 www netmask 255.255.255.255static (inside,outside) udp interface 5008 192.168.3.117 5008 netmask 255.255.255.255static (inside,outside) tcp interface 3390 192.168.3.101 3389 netmask 255.255.255.255static (inside,outside) tcp interface h323 192.168.3.118 h323 netmask 255.255.255.255
--------------end 7.2 commands----------------------
Cisco :: Command To List Firewall Rules?
May 17, 2012Boss wants a listing of the firewall rules only. What's a command I can run that will give me a listing of this?If I can get an output of firewall rules only, via GUI, that'll work too. It just needs to end up with a printout on a piece of paper telling me what the firewall is doing.
View 17 Replies View RelatedCisco Firewall :: Command For Configuring NAT On ASA5505?
Dec 5, 2012want to know the command for configuring NAT on My ASA5505.
Local IP - 192.168.1.0/241
Public IP - 182.73.109.118 255.255.255.252
Cisco Firewall :: Need Pix 506E Version 4.3 Command
Nov 19, 2012I have a PIX506E that was resently reset and it has version PIX Version 7.1(2) . It either uses some different commands or I am not using them correctly. [code]
View 2 Replies View RelatedCisco Firewall :: ASA 5580 Command Itself Is No Longer Used
Mar 5, 2011i'm new with the asa's...i'm familiar with the FWSM's on 6500's and pix..I'm running Version 8.3(2) and i wanted to setup nat-control and use of identify nats for advertising inside subnets to my outside networks.
the old command was static(inside,outside) 10.x.x.x 10.x.x.x netmask 255.255.255.x i'm having a little difficulty decyphering the pdf about the static nat...the command itself is no longer used, nat-control is no longer used, but i'm not quite sure what the equivalent nat command is that equates to the old static inside,outside command.
Cisco Firewall :: Save Command Output To Flash On ASA 8.4?
May 28, 2012How do you save the command output from the CLI to a file on flash?
With IOS, I would normally use a pipe command to redirect to tftp, but the ASA doesn't support this as far as I can tell. As a work around I was thinking I could save the output to flash and then tftp that file off the ASA.
Cisco WAN :: 2921 How To Access Firewall From Command Line
Jun 11, 2012we just bought a 2921 with the following modules: 4 port clear channel T1/E1 HWICSM-ES3G-24-P: EtherSwitch.I read some CISCO documents, and not be able to find what I need. I would prefer all instructions from you are for CLI interface.This is my first time to deal directly with T1, WIC and 2921 etc. The following is what I get from ATT, IP masked IP Address Block IP Address: 20.20.20.136/29 WAN Link Details: WAN Link IP Address:13.13.13.92 AR Serial INT IP Address:13.13.13.93 CR Serial INT IP Address:13.13.13.94 WAN Link Subnet Mask:255.255.255.252
A: how do I configure T1, what does "AR, CR" stands for, and do I need to use both IP addresses? What is the WAN Link IP for?
B: We have two T1 lines, so I should plug them both to the WIC, say port 0 and port 1, how to configure them?
C: how do I access the firewall from the command line?
D: I followed T1/E1 HWIC installation guide, and as soon as I add channel-group to the controller t1, the serial interface went down?
Cisco Firewall :: 5580 Do Static Command Needed
Oct 3, 2011The firewall is running version #8.2 on ASA 5580. Address translation is not needed on Inside network and Outside network.But the customer has hundreds of static command as below.. [code] Can they all be removed and replace with one single command as below?
View 1 Replies View RelatedCisco Firewall :: Asa 722 Asdm Location Command After Upgrade
Sep 3, 2008Before running firmware asa722-k8.bin and asdm-522.bin ASDM "asdm location" config lines were created when we created a network object. After the upgrade to asa722-k8.bin and asdm-522.bin this dissapeared.We recently upgraded to asa724-k8.bin and asdm-524.bin which brought those config lines back.So if "asdm location" is needed, if not can we make sure those lines wont pollute the config file?
View 3 Replies View RelatedCisco Firewall :: 5520 - ASA 8.6.1 Shape Command Invalid
Jul 9, 2012Tried setting up a Shape Policy and it states its invalid. Worked fine on my 5520, just curious to know why its coming as invalid now
ciscoasa(config-pmap-c)# shape
^
ERROR: % Invalid input detected at '^' marker.
ciscoasa(config-pmap-c)# shape ?
ERROR: % Unrecognized command