Cisco VPN :: Missing Client Configuration Group Command - Old 2600 Router
May 9, 2012
I need to create a Cisco VPN Client connection: I am following the cisco vpn client link and I don't have the command crypto isakmep client configuration group XXXXX
[URL]
This is what I get: crypto isakmp client configuration ? address-pool Set network address for client
This is my show version, if there is an IOS that will work:
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IK9S-M), Version 12.2(17a), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2003 by cisco Systems, Inc.
On the Cisco forums, an example is shown for how to configure BVI and bridge-groups on an ASR1004 but the same command (bridge-group) is not available under the interface on our ASR routers. We are running version of code: asr1000rp1-advipservicesk9.03.06.00.S.152-2.S.bin
I came across an interesting issue and thought I would see if anyone else has encountered it before contacting TAC.I have two Cisco Catalyst WS-4510R-E switches with a single Supervisor V module in each chassis. Both Sup cards are now running 12.2(54) SG1; ipbasek9 firmware; yes, I plan to move both switches to 15 code but that's another story. Anyways, prior to the upgrade the one switch was running 12.2 (33) code; I suspect the code was never upgraded; running ipbase non - K9 code. The other switch was running 12.2(44) with K9 prior to upgrade to 12.2(54).
I have two Cisco Catalyst WS-4510R-E switches with a single Supervisor V module in each chassis. Both Sup cards are now running 12.2(54) SG1; ipbasek9 firmware; yes, I plan to move both switches to 15 code but that's another story. Anyways, prior to the upgrade the one switch was running 12.2 (33) code; I suspect the code was never upgraded; running ipbase non - K9 code. The other switch was running 12.2(44) with K9 prior to upgrade to 12.2(54). With the background set, one switch reports the following:SwitchA (config)#r?radius-server redundancy regexp represourc rmon route-map router.
Currently I'm using Cisco VPN client software to connect to a remote IPSec server on the workstations. I want to to configure IPSec client on Cisco 2600 router which connects to the remote IPSec server so the workstations can access VPN subnet without using VPN software. how to configure IPSec client on the router?
The only QoS command i have in global config is (no MLS qos) :
REMOTE-ROUTER1(config)#qos ? restore-show-output Restore old show output shape-timer Set the HQF shape timer interval
The router is running IOS:
System image file is "flash:c2801-ipbasek9-mz.151-4.M5.bin"
Am i just running the incorrect IOS or am i missing somehting, i need to change the QoS Map for my Nortel VoIP. The VoIP phones connect to a 3750 PoE which used to conenct to a 2651XM to route VoIP and data traffic over the same copper pairs (WAN link to hub site) hence the need for a Service policy but being Nortel phones, require changing the cos-dscp map. the 2801 is going to replace the 2651XM using a new HWIC.
I have a stack of 3750's running IOS 12.2(25). "IP forward-protocal" command is configured, but the IP helper command is just not an option to put on an interface. Any have any idea of why that could be?
My 3550 is always 2 characters short on the command line. So my global configuration mode will look like this:Switch3550(config Say I wanted to enabled ftp, it would look like:Switch3550(config)# ftp enab.
I've finally got my 3560 switch IPv6 capable (IP Services IOS), but I've stumbled upon something strange: I can configure a tunnel interface, but I can't put the tunnel in ipv6ip mode. The command is missing. I can choose GRE, IP in IP, and a bunch of other things, but no ipv6ip. I'm a bit desperate here and probably I am going to have to live with it, but just in case? I need the IPv6 tunnel for an uplink to a tunnel broker which only supports this type of tunnel, and I'm surprised this is missing.
My customer has upgrade his 4506 from 6L-E to 7L-E 10GE.Ever since then if he run the command show dot1x interface gigabitEthernet x/x details some information are not been displayed (below are missing information)Is this intensional or do I need to kick this to TAC?
I have two Aironet 1231Gs, that are both running the same version of fimware: Version 12.3(8)JEE
From the gui, I try and change the channel on the main radio interface--It works from one, and I get just a blank page on the other. When I try and change it via the cli, I use the "channel" command in conf int mode, and it works one the one, but the other one, the "channel" command doesnt exist.
I have been looking around and I can not find the " crypto isakmp policy " command on this Cisco Router 1941. I just wanted to setup a regular IPSEC Lan to Lan tunnel and surprise, the command is not there. Do I have the wrong IOS? I thought that a K9 image would do the trick. [code]
I recently rebuilt the configuration of our Cat6500 multilayer device for use as a user stack. The device is funtioning as it should be, but I am unable to set SSH using the 'crypto key generate rsa' command. The crytop command isn't avaiable at all, which suggests a firmware issue.
I have configured a hostname and Ip domain-name and the image is the only one available.
The show version output is listed below. show verCisco Internetwork Operating System SoftwareIOS (tm) s72033_rp Software (s72033_rp-IPSERVICES_WAN-VM), Version 12.2(18)SXF12, RELEASE SOFTWARE (fc2)Technical Support: [URL] Copyright (c) 1986-2007
This question might actually belong under tacacs server but it's only happening with the ACE. I've configured tacacs on the 4710 and configured the tacacs server per the documentation. If I enter the shell:<context>*Admin default-domain under the group settings when I login with my tacacs ID my role is set to Network-Monitor. If I set the shell in my specific tacacs ID I'm assigned the correct role as Admin. We're running ACS ver 4.1 and the ACE is A4(1.1)
What is the maximum throughput of a 2600 AP when using CLient Link 2.0. I see that the datasheet states that it is 450mbps, however, from my understanding of transmit beamforming (client link 2.0), when traffic is "beamformed" to a client it cannot use spatial multiplexing on the same antenna as well. If this is the case, with the 2600 only having 3 transmit antennas, does this mean that the max throughput to a client when using clientlink is 300mb ?
If not, how the AP transmit at 450mbps and beamforms at the same time.
I have a Cisco 2951 Router and I am trying to set it up to use DHCP and for security purposes I need to use the "IP Access-Group in" command. The DHCP will not work when I have this command on the interface that I need to run it through, DHCP works fine when I do not have the "IP Access-Group in" command in the configuration. When I check the log after the failed DHCP attempt it shows up as denied, as if it's being blocked. The IOS I have is c2951-UNIVERSALK9-m 15.0 (1) M3. Conf Reg 0x2102.
I ordered a set of hardware that came with CBT videos; however, the videos they sent do not exactly match the hardware and I'm stumped.
I have 3 routers:
2610XM: Indianapolis 2620:New_England 2610:Seattle Indianapolis connects to New_England with a WIC-1DSU-T1 Indianapolis connects to Seattle with a WIC-1T
The interfaces are up on all three devices and so are the protocols. The videos are of 2500 series routers and they only use the WIC-1T card. When I try to set the clock rate for the s0/1 on New England to 1000000 like the video suggest I get an error "this command only applies to DCE interfaces". Do I not need to set this on the WIC-1DSU-T1 interface?
Whenever I issue router rip and try to set network such as:
the network won't save on any of the devices. If I show the running-config it shows network 10.0.0.0 I've tried saving the config directly after exiting outt of the config mode, but still only 10.0.0.0
I have configured my ASA5520 to act as VPN server. It accepts connections from the internet and then it authenticates the user to a Windows 2008 Server via Radius.Everything works fine if I use the VPN client embedded in Microsoft Windows. Conversely, if I try to configure Cisco VPN Client, I cannot find where to define the PSK string.
I have a strange issue with clients connected to a WiFi network.I have configured AP in FlexConnect mode and 2 SSID's. After a reboot of the AP the network is stable for almost 45 mins. Then each client will go UP and Down, mostly with a delay of 5 mins.
What could be the source of this. The clients are Windows CE handheld with fixed IP adres. I already configure persitent client and have play arround with APR timers as well. Thereby an Windows desktop or an iPad has less connectivity issues but even they expert pakcteloss once in severall minutes.
Session timer is turned off
The iPad for example can play music, but each 5 mins you hear a little hickup and 2 subsecond ping are loss.
Here is my current config build for a Cisco 2620 using a Wic-1ADSL to connect to a Qwest ADSL ISP:
interface FastEthernet0/0 ip address 172.16.0.1 255.255.0.0 ip nat inside no ip mroute-cache
[code]...
For some reason, it won't connect at all. I've changed the callin requirement on the ppp authentication between "callin" to "callout" - even removed the line completely for a no-authentication scenario.The only responses that come back on a repetative nature when doing a debug are:
I have been trying to manually disable clients from within WCS by calling up the client in 'Monitor Client' and then in previous versions you used to be able to select 'Disable Client' from the drop down list. This would take you to the template page where you would deploy this to the controller(s). It's not there anymore in my version. It means you have to do it manually, which is really annoying.
I have a /25 block of public ips from my ISP which I'd like to subnet into two /26 blocks. I have a Cisco 2600 with 2 ethernet ports in it. What are the commands I'd need to take my 200.180.200.0 255.255.255.128, gateway 200.180.200.1 and turn it into 200.180.200.0 255.255.255.192, gateway 200.180.200.1 and 200.180.200.64 255.255.255.192, gateway 200.180.200.65? One of the interfaces will be connected to the ISP & the other to a switch, and then we could access the two subnets through the switch.
I have a Cisco 2600 with IOS 12.3. I need a very basic configuration to allow traffic between two LANs. To test this I cleared the router config to the factory default state and configured my network addresses on the interfaces.
When I connected a PC to each interface I found they could ping each other, I was expecting to have to write ACLs to permit the traffic into the interfaces, thinking that the default behaviour of the router would be to deny access. default bahaviour without any ACLs or other routing configurations?
My config, such as it is, is as follows:
Current configuration : 770 bytes version 12.3 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption
I'm trying to configure a disco router 2600, my internet connection is via a cable modem. I get a dynamic IP from the cable modem but when I ping to any external IP I have errors.Copy show config and show interface f0/1
GUEST#show config Using 1103 out of 29688 bytes ! version 12.2 service timestamps debug uptime service timestamps log uptime no service password-encryption [ code]...
I have configured a lab for RA VPNs with a ASA5510 software version 8.2 and VPN Client 5 using digital certificates with Microsoft CA on a Windows 2003 server. I did the configuration based on this document from Cisco website: URL
Now the vpn works just fine, but now I need to configure different tunnel-groups so I can provide different services to different users. The problem I have now is that I don't know how to configure it so the certificate matches the tunnel-group name. If i do a debug crypto isakmp on ASA I get this error messages:
%ASA-7-713906: IP = 165.98.139.12, Trying to find group via OU...%ASA-3-713020: IP = 165.98.139.12, No Group found by matching OU(s) from ID payload: Unknown%ASA-7-713906: IP = 165.98.139.12, Trying to find group via IKE ID...%ASA-3-713020: IP = 165.98.139.12, No Group found by matching OU(s) from ID payload: Unknown%ASA-7-713906: IP = 165.98.139.12, Trying to find group via IP ADDR...%ASA-7-713906: IP = 165.98.139.12, Trying to find group via default group...%ASA-7-713906: IP = 165.98.139.12, Connection landed on tunnel_group DefaultRAGroup
So basically when using certificates I always connect the RA VPN only with the default group DefaultRAGroup. Do I need to use a different web enrollment template for certificate request instead of the user template??? How can I define the OU on the User certificate so it matches the tunnel-group???
Profile in atthach-file. After this profile is uploaded to client Optimal Gateway Selection doesn't work propertly: When 'vpn1.mydomain.com/mygroup' (it best TTL server) is unreachable, then OGS try to be connected to other servers, but without group-url, for example 'vpn2.mydomain.com' (instead of 'vpn2.mydomain.com/mygroup')
We have ASA5500's deployed for remote access concentration.We use Cisco IPsec vpn client with a group policy the chacks for Network ICE BlackIce ersonal firewall.The powers-that-be wish to change to McAfee presonal Firewall ok..Now the Group Policy allows you to check for several pre- configured Firewalls, Cisco Integrated, Sygate, Zone Labs etc.So as McAfee are no listed then I am to assume we go for "Custom Firewall" and this is where I am struggling.To configure checking for a Custom Firewall I must have the Vendor ID and the Product ID.McAfee haven't the faintest idea what we're talking about when we ask them for these details.Or is there a way to extract them from the registry of a machine with the McAfee product installed?
Looking to fine tune Cisco IPSec client RA-VPN authentication on our ASA-5510. Currently using NT Domain authentication. It's been working fine for quite a while but is too broad a brush. It authenticates anyone who is in the domain. We need to only authenticate folks who are in a specific AD remote access security group. I'm testing LDAP but am getting the same results. I can get it to authenticate based on overall domain membership but can't seem to figure out how to check group membership.
We've updated to ASA 8.2(1) and ASDM 6.2(1). It seems to have more LDAP functionality but I'm not an LDAP expert. I've posted an image of the LDAP server dialog from the ASDM. I originally tried putting the Group DN in the Base DN field but kept getting a "can't find user" error when testing. I also tried adding the group info in the "LDAP parameters for group search" field at the bottom. But it doesn't seem to be looking there. Note that the current value is the Group Base DN only. I also tried putting "memberOf=" in front of that. Still no luck. The values shown in the image work for simple domain membership.
