Cisco WAN :: 2600 CCNA Lab Configuration?
Sep 6, 2012
I ordered a set of hardware that came with CBT videos; however, the videos they sent do not exactly match the hardware and I'm stumped.
I have 3 routers:
2610XM: Indianapolis
2620:New_England
2610:Seattle
Indianapolis connects to New_England with a WIC-1DSU-T1
Indianapolis connects to Seattle with a WIC-1T
The interfaces are up on all three devices and so are the protocols. The videos are of 2500 series routers and they only use the WIC-1T card. When I try to set the clock rate for the s0/1 on New England to 1000000 like the video suggest I get an error "this command only applies to DCE interfaces". Do I not need to set this on the WIC-1DSU-T1 interface?
Whenever I issue router rip and try to set network such as:
router rip
network 10.0.1.0
network 10.0.10.0
network 10.0.20.0
the network won't save on any of the devices. If I show the running-config it shows network 10.0.0.0 I've tried saving the config directly after exiting outt of the config mode, but still only 10.0.0.0
View 4 Replies
ADVERTISEMENT
Apr 17, 2008
Here is my current config build for a Cisco 2620 using a Wic-1ADSL to connect to a Qwest ADSL ISP:
interface FastEthernet0/0
ip address 172.16.0.1 255.255.0.0
ip nat inside
no ip mroute-cache
[code]...
For some reason, it won't connect at all. I've changed the callin requirement on the ppp authentication between "callin" to "callout" - even removed the line completely for a no-authentication scenario.The only responses that come back on a repetative nature when doing a debug are:
Vi2 PPP: Authorization NOT required
and
Vi2 PPP: No remote authorization for call-out
View 2 Replies
View Related
Sep 5, 2012
I have a /25 block of public ips from my ISP which I'd like to subnet into two /26 blocks. I have a Cisco 2600 with 2 ethernet ports in it. What are the commands I'd need to take my 200.180.200.0 255.255.255.128, gateway 200.180.200.1 and turn it into 200.180.200.0 255.255.255.192, gateway 200.180.200.1 and 200.180.200.64 255.255.255.192, gateway 200.180.200.65? One of the interfaces will be connected to the ISP & the other to a switch, and then we could access the two subnets through the switch.
View 6 Replies
View Related
Dec 16, 2011
I have a Cisco 2600 with IOS 12.3. I need a very basic configuration to allow traffic between two LANs. To test this I cleared the router config to the factory default state and configured my network addresses on the interfaces.
When I connected a PC to each interface I found they could ping each other, I was expecting to have to write ACLs to permit the traffic into the interfaces, thinking that the default behaviour of the router would be to deny access. default bahaviour without any ACLs or other routing configurations?
My config, such as it is, is as follows:
Current configuration : 770 bytes
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[code]....
View 5 Replies
View Related
May 2, 2012
I'm trying to configure a disco router 2600, my internet connection is via a cable modem. I get a dynamic IP from the cable modem but when I ping to any external IP I have errors.Copy show config and show interface f0/1
GUEST#show config
Using 1103 out of 29688 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
[ code]...
View 3 Replies
View Related
May 9, 2012
I need to create a Cisco VPN Client connection: I am following the cisco vpn client link and I don't have the command crypto isakmep client configuration group XXXXX
[URL]
This is what I get: crypto isakmp client configuration ? address-pool Set network address for client
This is my show version, if there is an IOS that will work:
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IK9S-M), Version 12.2(17a), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2003 by cisco Systems, Inc.
[Code].....
View 1 Replies
View Related
Apr 11, 2013
After some searching I see many people using power injectors or switches that supploy PoE. I am building a lab for the CCNA Wireless and currently have an old Cisco 3550 PoE switch and a 2106 Controller that I got at a steal of a price. My question is, The 1142 can use the 15.4 Inline Power from the 3550 even though it is not the 802.11af standard correct? If it doesn't then I will need to order a power brick.
View 3 Replies
View Related
Jul 4, 2012
I'm looking to sit the ICND2 exam soon and have discovered that the pair of old 2924XL switches are not going to cut the mustard for the newer vlan commands and other features.
Would a pair of WS-C3550-24-SMI switches be a sensible replacement for ICND2 and possibly up to CCNP? They are available on ebay for about £80 each.
View 4 Replies
View Related
Aug 17, 2011
I am new to this forum. I ve been googling for CCNA explorer for last one month. All the versions that i download is not compatible with windows 7 and works fine with windows XP. Does anyone know if cisco has released any new version that is compatible with Windows 7?
View 6 Replies
View Related
May 16, 2011
What's the best router / handset to get to practice for CCNA Voice?
View 2 Replies
View Related
Nov 14, 2012
I'm reading the CCNA Sec book (554) and I've just finished a few chapters on CCP.Is the tool free? Can it be simulated in PT, or emulated in GNS3? Speaking of which, can the entire CCNA/CCNP Sec track be emulated in GNS3?
View 6 Replies
View Related
Jun 30, 2011
I'm looking at purchasing one Cisco 2600 XM Series router that has IOS 12.4 on it. I put the IOS name into Cisco's feature navigator and it states that it supports SSH and IPv6. Can I buy that router, take the IOS off that one, and put it on another 2600 XM Series so I don't have to spend $400 on two routers with 12.4 on them?
View 3 Replies
View Related
Sep 30, 2011
I am trying to secure sub interfaces on a 2600 Router
interface FA0/1.1
No Access-group
Interface FA0/1.2
IP Access-group 110 out
Access-list 110 deny ip 2.2.2.0 0.0.0.255 1.1.1.0 0.0.0.255
Access-list 110 permit ip any any
This works but it blocks traffic both ways I only want to block one, I dont want FA0/1.2 to be able to access FA0/1.1 but I want all traffic to be allowed to go the other way
View 2 Replies
View Related
Jul 13, 2011
I have a cisco 877 router connected to our adsl broadband at our head office. I have managed to set this up with Nat and DHCP all working to let multiple users access the internet through our single static ip supplied by the ISP lets say the ip is 1.2.3.4.Our internal network is 192.168.1.0 255.255. 255. 0.I have a draytek vigor 2600 at a branch office set up the same with a static ip addresss supplied by the ISP lets say the ip is 5.6.7.8.The internal network is 192.168.4.0 255.255.255.0
I am trying to set up a VPN between the head office and branch office so the branch office users can connect to our internal server(lets say ip is 192.168.1.2) to receive group policies,access files and also telnet into our database server(lets say ip is 192.168.1.3).I have attached a sort of running config that i have pieced together from bits i have read on this site and others. I have tried these settings and other permutations of these settings but i cant seem to establish a tunnel even though when i show int tunnel0 on the router it says tunnel is up and line protocol is up, if i show ip route it shows that there is an ip address for the tunnel and that is about it(No vpn light on).
If it makes sense and that I have entered the right information? I have highlighted the parts i am not sure about in red(Quite a bit and obviously not the exact settings but what i think it should be). Once all the settings are correct on the cisco will it automatically establish the vpn or do i have to dial it from the draytek.
View 4 Replies
View Related
Mar 4, 2012
i want to configure the router for internet access for hosts this is the my pub ip x.x.x.174 and mask 255.255.255.252 this is isp given subnetmask internal ip range is x.x.x.20-x.x.x.254
View 1 Replies
View Related
Mar 14, 2013
I am new using cisco router 2600, i want to use dmz like adsl modem to direct ip public to ip lan like 180.15.22.x.x to ip lan 192.168.1.2 ( lrouter mikrotik ) outside to inside so when i call ip public then forrward to mikrotik
View 2 Replies
View Related
Aug 24, 2011
I was trying to erase my lab router 2600 and reset it back to the factory defaults. Well I was able to to reset it all right but I used the erase command which worked a little to well. So now there is no IOS and the router is in ROM mode and I didnt back up the pervious IOS "Nice". So was able to get an updated IOS for my 2600 but I'm trying to install it and don't know how. I was able to get a tftp server app for my windows pc but I'm unsure on how to configure it so I can transfer the new IOS to the router. On the up side I did learn something erasing and reset are to very different things.
View 6 Replies
View Related
Jun 20, 2012
I have 3 Cisco 2600 routers with the same IOS and memory.One of them has CME...
What would be the best way to copy the CME from the one router over on the other two?Backup my FLASH to my TFTP and then restore to the other two routers?
View 1 Replies
View Related
Jun 10, 2013
I have a 2600 I am trying to setup for educational use.
My Cable ISP has issued me 5 routable IP's through their SMC modem 86.28.12.226-229. The SMC modem is .225. Currently the internal network can get out through .229 as expected but nothing outside (tcp 80 to web server) can get through. When I assigned the ip's to e0/1 as secondarr I could get it to route from the inside network (so hitting .226 80 went to the correct place) but it still didn't work from the outside - plus I read that wasn't a great way to do it anyway.
!
interface FastEthernet0/0
description LAN Interface
[Code].....
View 2 Replies
View Related
Jan 2, 2012
I nedd some Details for configuring the new internet connection from ISP.
I Will discribe the Curent network structre . We have a internet conection from one vendor That is comming to our router. we are using Cisco router 2600 that having two Ethernet ports.One port occupaid with connection from ISP ,One port going to ASA firewall.
We have a site site VPN conction with client between our ASA and thier ASA.
Now we need to configure one New internet Connection from another vendor .We need to use this new connection mainly for VPN.And once this connection is down we need to backup with old Connection.
how we will take the connection to the firewall or do we need to configure the new router.we have a new router.
View 6 Replies
View Related
Nov 10, 2011
- I have an older router 2600 running 12.1(4) IOS.
- There are a few clients connected to it via the frame relay connection.
- There is an IP that clients access 192.168.1.10 for example
- We need to do a NAT for this IP for one specific client only like "ip nat inside source static 192.168.1.10 1.1.1.1"
- However if I do that, that will effect other clients too
- On the interface for this client I'll be using "ip nat outside"
- Is there a way to accomplish this without effecting other customers?
View 6 Replies
View Related
Dec 29, 2012
How to know the serial 0 or 1 (to v35 modem)was good or not ? is there any tool (software) or hardwire jumper to simulate loop back ?
View 12 Replies
View Related
Apr 11, 2006
How to know the serial0 or 1 (to v35 modem)was good or not ? is there any tool (software) or hardwire jumper to simulate loop back ?
View 4 Replies
View Related
Sep 10, 2011
I have two LANs in my house, one 10/100 base and the other 10/100/1000, but one internet connection that I would like to have access to on both networks. Right now I have two Belkin routers for each network. In addition I have a Cisco 2600 and 3660. I know they are old, but they seem to be in operational order. Can I use those to combine to two networks? The only thing I want to maintain is the speed on the gig network, from the router to the PC's and devices.
View 6 Replies
View Related
Jan 11, 2012
I have cisco 2600 router. The problem is my router ios has been crashed and i unable to use any mode on my router. I need to install new ios. How can i install or upgrade new ios step by step.
View 1 Replies
View Related
Sep 17, 2012
I am trying to configure SDM 2.5 on a cisco 2600.I have access via telnet to the router and was able to change the enable password - which i think is level 15 (right?) and setup (and bring up) the ip on the ethernet interface. I can ping - and get response from - the router Trying to install SDM on the router i need to provide the default username i tried both admin/administrator but SDM can't communicate with the router?
View 21 Replies
View Related
Apr 16, 2013
we have some (2) HP Notebooks with a Broadcon 4313 b/g/n WLAN Chip and use the latest drivers (2012). This Chip can provide up to 72 mbit/s with 2,4 ghz.
If we connect this notebooks to a Aironet 2600 AP (10 feet distance) the Windows 7 WLAN Dialog shows 72 Mbit/s for 3 seconds and than only 5.5 Mbit. Others (newer) Laptops show 450 Mbit. The WLAN works with WPA2/AES and PSK. The speed doesn't go up, if we copy a big file to the laptop.
Here is the Linktest from the AP to Client (from the WLC 2504 Webinterface):
View 12 Replies
View Related
Jun 20, 2012
I've got a 2600 that I am wanting to connect to my cable modem. However I don't have the knowledge to get it running. My ISP uses a dynamic IP and I am unable to get it to connect.
ROUTER#show run
Building configuration...
Current configuration : 685 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
[code].....
View 7 Replies
View Related
Jan 16, 2013
Currently I'm using Cisco VPN client software to connect to a remote IPSec server on the workstations. I want to to configure IPSec client on Cisco 2600 router which connects to the remote IPSec server so the workstations can access VPN subnet without using VPN software. how to configure IPSec client on the router?
View 20 Replies
View Related
Oct 1, 2011
The wan routers are 2600 and 1700. Conversions between the two? Pros/Cons of one versus the other? Regrets or horror stories for one versus the other?
View 3 Replies
View Related
Feb 16, 2011
I am planning to have 2600 routers with Hardware compression module to accelerate the application performance and to optimize the wan bandwidth.I checked it 10 times optimize the bandwidth. Any pros and cons of these module.I searched in web but didn't get exact points.
View 1 Replies
View Related
Feb 24, 2013
Was just wondering if we can segregate users using subnets and not vlans in cisco switches? We have few groups we want to segregate onto different subnets, but don't want to use Vlans. Apparently I have been told that vlans do way too much packet processing and slows the network.
we are working on a school network. Want to segregate staff/students/admin.Further segregate students by year levels. This means if we were to use vlans we would have around 15 vlans. will it slow the network? (thats what I have been told and i dont agree to it). How to implement this topology without vlans and by just using subnets.PS: we use Juniper EX4200 (layer3), Juniper EX2200 x15,H3C 3100 x16 and cisco 2600 x1 switches on campus.
View 1 Replies
View Related
Apr 17, 2011
I have configured VPDN/Dialer on router 2600 to connect to our ISP via Fibre Optics modem but its simply not connecting. The router consists of 3 interfaces
- Inter fa0/0 = 10.0.0.6 255.255.255.248 (LAN 1)
- Inter fa0/1 = IP is unassigned (interface connected to Fibre Optics modem)
- Inter e1/0 = 192.168.200.1 255.255.255.0 (LAN 2)
The connection is planned to run like this:
LAN1 & LAN2 (Inter fa0/0 & Inter e1/0) <-> Inter fa0/1 <-> Dialer1 <-> Modem <-> ISP <-> Internet.
The Modem will just server as mere "modem" or just a bridge, as the actual routing is configured on "dialer interface" in the router.We're not using a dedicated IP address to link to ISP but a public one. After configuring the interfaces, VPDN, dialer interface, NAT, access-list, ISP's assigned username/password, etc I'm simply not connecting to our ISP, even when I do a ping. The ISP's IP address which we're pinging is 118.23.8.80 What am I missign out? How do I connect the dots here?Below are the results for Running config, Ping, and Debug:
Running Config:
Router1#show running-config
Building configuration...
Current configuration : 3083 bytes
!
! Last configuration change at 17:39:43 Sun Apr 17 2011
!
version 12.3
[code]....
View 2 Replies
View Related