Cisco WAN :: 2600 Sample Subnet Configuration Required
Sep 5, 2012
I have a /25 block of public ips from my ISP which I'd like to subnet into two /26 blocks. I have a Cisco 2600 with 2 ethernet ports in it. What are the commands I'd need to take my 200.180.200.0 255.255.255.128, gateway 200.180.200.1 and turn it into 200.180.200.0 255.255.255.192, gateway 200.180.200.1 and 200.180.200.64 255.255.255.192, gateway 200.180.200.65? One of the interfaces will be connected to the ISP & the other to a switch, and then we could access the two subnets through the switch.
View 6 Replies
ADVERTISEMENT
May 30, 2011
I'm having trouble getting Tacacs+ to work correctly with ACS5.1 and a simple catalyst 3750 switch.I can authenticate with AAA, however i cannot get a single command to work once i'm in; "Command authorization failed" even on "enable".
Any useful resource that will walk me through the process?
View 3 Replies
View Related
Sep 22, 2011
sample configuration for internet failover . i have 2 ISPs with one coming in thought a serial cable and another through internet and would wish one take over after the other has failed .The router is Cisco 1921 .
View 4 Replies
View Related
Jan 10, 2012
Any sample qos configuration that is enabled on a 6509 for voip ? it would be nice if its a auto-qos . I do not have an available 6509 to try this.
View 2 Replies
View Related
Mar 18, 2013
Any sample configuration of c1310 as a work group bridge.
View 2 Replies
View Related
Apr 26, 2012
I'm trying to find a document in Design Zone about configuring a Wireless AP and I wasn't able to find it. I have a good experience configuring switches, routers and firewalls in CLI and this is the first that I have my hands on APs (1240 AG).
View 2 Replies
View Related
Jun 13, 2012
Where can I find a sample working configuration of (HP rebadged) 3120 Blade Switch?
I have the Cisco 6500 end configured as follows:
interface Port-channel1
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,300,304,310,320,560-562,600,740,770,950
switchport mode trunk
load-interval 30
[code]....
I will be connecting 9/5 and 9/6 to Cisco 3120G (HP rebadged) Blade Switch in c-Class Enclosure tomorrow.It would be nice to have a rough sample configuration of the above 3120G switch.
View 5 Replies
View Related
Sep 6, 2012
I ordered a set of hardware that came with CBT videos; however, the videos they sent do not exactly match the hardware and I'm stumped.
I have 3 routers:
2610XM: Indianapolis
2620:New_England
2610:Seattle
Indianapolis connects to New_England with a WIC-1DSU-T1
Indianapolis connects to Seattle with a WIC-1T
The interfaces are up on all three devices and so are the protocols. The videos are of 2500 series routers and they only use the WIC-1T card. When I try to set the clock rate for the s0/1 on New England to 1000000 like the video suggest I get an error "this command only applies to DCE interfaces". Do I not need to set this on the WIC-1DSU-T1 interface?
Whenever I issue router rip and try to set network such as:
router rip
network 10.0.1.0
network 10.0.10.0
network 10.0.20.0
the network won't save on any of the devices. If I show the running-config it shows network 10.0.0.0 I've tried saving the config directly after exiting outt of the config mode, but still only 10.0.0.0
View 4 Replies
View Related
Apr 17, 2008
Here is my current config build for a Cisco 2620 using a Wic-1ADSL to connect to a Qwest ADSL ISP:
interface FastEthernet0/0
ip address 172.16.0.1 255.255.0.0
ip nat inside
no ip mroute-cache
[code]...
For some reason, it won't connect at all. I've changed the callin requirement on the ppp authentication between "callin" to "callout" - even removed the line completely for a no-authentication scenario.The only responses that come back on a repetative nature when doing a debug are:
Vi2 PPP: Authorization NOT required
and
Vi2 PPP: No remote authorization for call-out
View 2 Replies
View Related
Dec 16, 2011
I have a Cisco 2600 with IOS 12.3. I need a very basic configuration to allow traffic between two LANs. To test this I cleared the router config to the factory default state and configured my network addresses on the interfaces.
When I connected a PC to each interface I found they could ping each other, I was expecting to have to write ACLs to permit the traffic into the interfaces, thinking that the default behaviour of the router would be to deny access. default bahaviour without any ACLs or other routing configurations?
My config, such as it is, is as follows:
Current configuration : 770 bytes
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[code]....
View 5 Replies
View Related
May 2, 2012
I'm trying to configure a disco router 2600, my internet connection is via a cable modem. I get a dynamic IP from the cable modem but when I ping to any external IP I have errors.Copy show config and show interface f0/1
GUEST#show config
Using 1103 out of 29688 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
[ code]...
View 3 Replies
View Related
Oct 18, 2011
I am very confused on how I setup a Pix 515 that I just got to route traffic out a cable modem. First, let me give you a little details on my current network setup and what I am trying to accomplish with this Pix 515. Currently all my users go out the proxy for any internet access, however I have certain users that need to go out the cable modem instead of the proxy server. Below is an example of the current IP setup of a user A:The cable modem that we currently have has DHCP so I would need the external PIX address to accept a DHCP address. I also don't really understand what else I need to setup so if I have say four users hitting the cable modem through the pix how do I direct their web traffic to the correct computer (NAT ?),I will be plugging the PIX into a cisco switch that all ports are in VLAN 48 so hopefully a static internal address on the pix of 10.24.48.254 will keep me from having to do any routes since all traffic will be originating from the 10.24.48.0 network.
View 1 Replies
View Related
May 9, 2012
I need to create a Cisco VPN Client connection: I am following the cisco vpn client link and I don't have the command crypto isakmep client configuration group XXXXX
[URL]
This is what I get: crypto isakmp client configuration ? address-pool Set network address for client
This is my show version, if there is an IOS that will work:
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IK9S-M), Version 12.2(17a), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2003 by cisco Systems, Inc.
[Code].....
View 1 Replies
View Related
Jun 6, 2012
We have purchased a new Websense 10000 Appliance and I'm not a hundred percent how to set this up. I see that URL Filtering is a possibility and WCCP, which way to move forward on implementing this?
View 4 Replies
View Related
Apr 19, 2011
I am trying to set up my Cisco 520 router with a firewall that will: Allow port 80 traffic to the vlan 20,Block all other incomming ports to vlan 20 (unless initalised from inside),Allow all outgoing ports on vlan 20,Block all access from vlan 20 to vlan 10 (unless initalised from vlan 10)
View 35 Replies
View Related
Apr 29, 2013
I have a problem with the configuration of the ACL of my ASA 5505 router.However, the syntax seems okay,access-list 121 extended deny icmp 192.168.0.0 255.255.255.0 .
View 3 Replies
View Related
Feb 9, 2012
How can I have access to the cisco "AP#" prompt? When I try to acees the AP through hyperterminal, it gives me the attached messages. The message keeps looping and not letting me access the AP# command prompt to assign an IP address so that I can control it in mode HTTP.
View 2 Replies
View Related
Jan 14, 2013
I have a Cisco 2921 Router,with 3 giga interfacesi have a leased line for the internet with a public ip address and i want to configure this router as NAT /PAT gateway, so that users in my network can ue the internet by the router,my wan interface is g0/0 - ip 122.xx.xx.xx lan is g 0/1 -- 192.168.1.1 /24 . i have tried doing nat once but i was not able to make the wan port up.using cisco CP when i test the interface it givves error and i dont get internet to my users.
View 10 Replies
View Related
Jul 13, 2011
I have existing Sonic FW in my company we are moving from sonic FW to ASA 5510 Security plus lice. I have two ISP currently connected to sonic Firewall I am planning to implement Dual ISP configuration on ASA5510.
View 12 Replies
View Related
Apr 6, 2013
Who can give me a SNMPv3 configuration template.I tried many times has been a problem
View 5 Replies
View Related
Jun 12, 2012
RV082 configured for Dual WAN [Code]....
(2) identical DSL connections, configured as Static IP (not PPPoE) with modems in bridged mode. Static IP's are /25 subnet and same gateway ** this may be a problem? Dual WAN set for Load Balance, network service detection is OFF
We have a 2003 terminal server running and successfully receiving connections through both WAN connections. Depending on location, half the users are connecting to WAN1 IP and the other half to WAN2 IP. We are getting sporadic disconnects of the remote users when they are idle for a couple minutes and automatic reconnection of the session takes over a minute. If they close the (locked up) session and reconnect manually it will let them in right away.
Could the handling of the Dual-WAN be the culprit? Could the same gateway for both WAN's create this issue upstream (out of my control)?I am going to move everyone to connecting through WAN1 and then change to Smart Link Backup and see if the issues persist.
Another thought is to use a secondary IP on the terminal server and use Protocol Binding to match "All traffic" for IP1 to WAN1 and IP2 to WAN2, which theoretically would stabilize the situation?
View 36 Replies
View Related
Apr 22, 2012
I am replacing a cisco linksys router with a 1941w.
I have the 0/0 accepting a DHCP from the ISP then I have 0/1 going to a switch and hosting a dhcp server.
Where I have an issue is:
A) Finding a way to turn on the wireless and make it use the same DHCP as wired and setting up a user name/wep password
B) Turning on the GUI that is supposed to be embedded on this.
C) Finding a way to make the DNS point to the default gateway so that I don't have to set the address everytime we move the box.
Here is my current configuration, and with it I can get onto the wired network and get to the internet.
Current configuration : 4712 bytes
!
! No configuration change since last restart
version 15.1
[Code]...
View 6 Replies
View Related
Jan 3, 2012
I want to start implementing a small outdoor mesh network of 3 APs Aironet 1550 in order to grow afterward with more APs. Is there any way to configure those 3 APs in an outdoor mesh configuration (for example, only one RAP and two MAPs) without a Wireless LAN Controller or I have to have at least, one WLC? My idea is to have a WLC 5508, but at the very beginning I don't know if my budget is gonna allow me to cost the WLC.
View 7 Replies
View Related
Dec 14, 2012
We have implemented VSS on Cisco 6504-E switches using the 10GE links on the Sup-720-10GE. Two Cisco WLC 5508 controllers are planned to be connected in a LAG configuration, (consisting of eight links per LAG bundle) to each of the 6504-E chassis( Total of four WLC, two for primary and two for secondary). WLC HA feature may be implemented on the primary and secondary WLC controllers using the 7.3 latest code release.
View 9 Replies
View Related
Feb 20, 2012
We have 2 sites with 2 internet connections at each site. All are SRP527w routers. 1 is for internet and 1 is for a site to site VPN as,Currently we are using Static Routes on the PC's so they can access each server no matter what site they are at. I have looked at using the Static Routes section on the SRP's but cannot get it to work.
View 2 Replies
View Related
Oct 16, 2012
I've gotten to the point where I can test against active directory and get in, also I can get AD groups from my server on the ASA. My problem, I can't connect in via my AnyConnect client on my Android. I immediately get a "log in failed" and I know I'm using the right username/pass. Doing a little troubleshooting, I have attached my AnyConnect debug log and the results of the "debug ldap 255" command on the ASA. Also, I've used ldp.exe to determine I can connect in with the username/password combo I'm using.Combing through the AnyConnect logs I see a few instances of "global error unexpected" but no Google searches have brought up anything useful.
View 7 Replies
View Related
Dec 8, 2011
I am just going to deploy some new 4900Ms for a customer. Want to know if configuring management for 4900 (everything like NTP, AAA, SNMP , DNS ) is doable through management interface in management VRF and there are no caveats to be aware of.
View 1 Replies
View Related
Oct 9, 2011
a link is added between Vail and Telluride in case if one of Aspen links fail to prevent AS 400 to become isolated. This link runs IBGP between both routers. Because this is an iBGP link, both routers will exchange BGP routes freely and automatically enters those routes into the routing table. Anyways, this link is advertised to OSPF through the BGP-to-OSPF redistribution. However, the book included that link in the OSPF configuration because as the book says "Without it, the iBGP session will not form" ... I did't get this part because the link is physical not logical between Vail and Telluride. Before the link was logical and the TCP session was performed through Aspen that's why we needed Aspen to know about this link. But now, it is physical so the iBGP (TCP) session should be formed without including that link in the OSPF config.
View 9 Replies
View Related
Apr 30, 2007
I have a cable broadband installed in my home i just bought cisco 1200 series access point...now how to configure my access point. I believe I have to plugged fastethernet cable coming out of my cable modem to access point after that? What I have to do ....do I have to configure the cable modem as wlel or not???
View 2 Replies
View Related
Apr 7, 2013
This is regarding CISCO logging configuration.We palnned to implement enable logging on all the cisco nexus switchs.we are running HP arc sight in our DC this device monitor all the CISCO devices.We want to enable logging with this Arc sight device.Just I would like to know about config commands for Nexus device, what is the command to enable logs which is include "who is login & logout?, interface down information?,who was did conf t ? & every logs"
View 8 Replies
View Related
Feb 1, 2012
We have recently aquired a remote location which has a pre-existing flat network (172.16.X.X/16). Before we are able to convert them over to our new IP scheme, they have a need to have wireless connectivity on site. We have 4 1142's which I need to configure for them. I have experience configuring WLC's and autonomous AP's for networks with multiple vlans but have never configured AP's for a flat, single subnet network. I need to configure them for either guest access (internet only) or corporate access to network resources with radius authentication. Do I configure a native vlan as I would for a typical multi vlan network? Do I configure the switch port as an access port as opposed to a trunk beacause of the lack of layer 3? I basically need a sample configuration for this situation.
View 1 Replies
View Related
Mar 22, 2011
I am looking for a sample configuration for doing TACCAS+ on ACS 5.2 with an ASA 8.2.2.
View 1 Replies
View Related
Mar 31, 2013
I have one firewall need to be configured in transparent mode. I have inside and outside router. What is the configuration of transparent firewall ASA8.2. I didn't find the configuration on Cisco site.
View 17 Replies
View Related
