Cisco Switching/Routing :: 6509 Sample Qos Configuration
Jan 10, 2012Any sample qos configuration that is enabled on a 6509 for voip ? it would be nice if its a auto-qos . I do not have an available 6509 to try this.
View 2 RepliesAny sample qos configuration that is enabled on a 6509 for voip ? it would be nice if its a auto-qos . I do not have an available 6509 to try this.
View 2 RepliesWhere can I find a sample working configuration of (HP rebadged) 3120 Blade Switch?
I have the Cisco 6500 end configured as follows:
interface Port-channel1
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,300,304,310,320,560-562,600,740,770,950
switchport mode trunk
load-interval 30
[code]....
I will be connecting 9/5 and 9/6 to Cisco 3120G (HP rebadged) Blade Switch in c-Class Enclosure tomorrow.It would be nice to have a rough sample configuration of the above 3120G switch.
I am position to migrate from CatOS 6509 switch to native IOS 6509 switch. long time ago, there was some site to convert automatically based on copy and paste onto the tool, but i can not find.
Does anybody know how to convert CatOS configuration to Native IOS configuration ? It is not IOS change, but it is configuration convert.
After a abrupt power cylce of 6509 switch, vlan configuration got missing. Switch has not crashed.
View 4 Replies View RelatedI am planning on upgrading my 6509s to use VSS within the next few weeks. I have checked all of the hardware and software prerequisites, and we are good to go from that perspective.I do have more of a procedural question- my switches are already configured and in production, VLANs, HSRP (3 IP addresses per VLAN- 1 per switch plus virtual IP), etc. Does the VSS upgrade take all of this into account and rewrite the configuration correctly, or should I plan on redoing the entire config for the switches after the upgrade?
View 6 Replies View RelatedHow do I find out who made the last configuration change on a 6509 CAT switch with the following Show VER
WS-C6509 Software, Version NmpSW: 8.5(9)
Copyright (c) 1995-2007 by Cisco Systems
NMP S/W compiled on Apr 16 2007, 21:23:23
[Code].....
I came across a Catalyst 6509 switch configuration and have noticed some strange thing on the ether channel configuration side, it appears that it have interface port-channel 2 and port-channel 2A, what was that mean? its the ether channel not forming and joined together?
What wrong with the below configuration that cause it to automatic created another port-channel (2A) interface in this case?
[code]...
Last night I've upgraded a catlyst 6509 (non-redundant), during the upgrade I# run into the problem that the 6509 only wants to boot from sup-bootflash, and that it took an old image from sup-bootflash.I deleted this old image and then the node came into rommon mode.There I did the boot command and refered to the correct image on disk1:Now the boot succeeded. Just in time before I run out of my maintenance window.
I did some investigation and looked into the supervisor (using attach 5 and remote command switch show boot) and detected that it's configuration register is on 0X2101 (This is because I run into problems a week ago because of a corrupt flash disk and changed this in rommon mode , without changing it back, I'm afraid I'm not totally known with the 6509)
Question is now how can I change the configuration register back to 0x2102 without any service interruption (It will cost me quit some goodwill if I have to boot the node for the third time in three weeks)?
We recently installed Cisco 6509-E with dual Sup 720-BXL. We are using this switch on internet Edge. Internet connection is terminating on 10GIG fiber port.We do have following line cards installed.
1. 10 GIG * 4 port line card
2. 1 GIG * 8 port line card
3. Empty
4. Empty
5. Sup 720-3BXL
6. Sup 720-3BXL
7. 1 GIG * 48 ports
8. 1 GIG * 48 ports
9. 1 GIG * 48 ports
We do have 2 GB internet pipe.We are running load test sending http port 80 request and when load reach to arround 100 to 200 mbps and connections from out side to inside 80,000 switch start reponding very very slow and start packet loss and when I try to ping from one server to second server it show normal ping but if I tried to ping gateway IP of server which is SWITCH IP it show packet loss and very high letancy.
Switch also throw message "No memory available: Update of NVRAM configuration failed"
I'm having trouble getting Tacacs+ to work correctly with ACS5.1 and a simple catalyst 3750 switch.I can authenticate with AAA, however i cannot get a single command to work once i'm in; "Command authorization failed" even on "enable".
Any useful resource that will walk me through the process?
I have a two fiber connection from our Central Office(6513) to Remote office (6509). I have a requirement that on the remote office if one of the fiber goes down, the second fiber should work as a failover. I am planning to use SUP720-3B SFP to connect to the CO.
Can I connet one fiber to Sup720-3b G5/1 & another fiber connection to G5/2? or Can I connet one fiber to Sup720-3b G5/1 & another fiber connection to G6/2? I am running EIGRP between sites. Any sample config.
sup-bootflash:s72033-pk9sv-mz.122-18.SXD7b.bin"
I have a /25 block of public ips from my ISP which I'd like to subnet into two /26 blocks. I have a Cisco 2600 with 2 ethernet ports in it. What are the commands I'd need to take my 200.180.200.0 255.255.255.128, gateway 200.180.200.1 and turn it into 200.180.200.0 255.255.255.192, gateway 200.180.200.1 and 200.180.200.64 255.255.255.192, gateway 200.180.200.65? One of the interfaces will be connected to the ISP & the other to a switch, and then we could access the two subnets through the switch.
View 6 Replies View Relatedsample configuration for internet failover . i have 2 ISPs with one coming in thought a serial cable and another through internet and would wish one take over after the other has failed .The router is Cisco 1921 .
View 4 Replies View RelatedAny sample configuration of c1310 as a work group bridge.
View 2 Replies View RelatedI'm trying to find a document in Design Zone about configuring a Wireless AP and I wasn't able to find it. I have a good experience configuring switches, routers and firewalls in CLI and this is the first that I have my hands on APs (1240 AG).
View 2 Replies View RelatedI currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3
I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis?Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3.I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis. Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
I'm moving into a new data center. I don't consider myself a network engineer or anything but I do understand the basics. The new data center I am moving into routes my network to me a bit differently than my old data center. The IOS on the Cisco 2621 is: c2600-i-mz.123-26.bin
I am assigned a /29 block which they configure as the routing network, it looks like this: Routing Network: A.A.A.0Routing Network Sub net Mask: 255.255.255.248Routing Network Def Gateway: A.A.A.1Customer Usable Address: A.A.A.4
I've been assigned a /28 block which is B.B.B.240/28. They stated that in order for me to use my allocated blocks, I had to act as my own gateway, routing the traffic through the routing network. This goes just a bit beyond my networking knowledge, though I still understand it, I just don't know exactly how to execute. I'm assuming my 2621 with 2 Fast Ethernet interfaces should be able to handle this routing scenario.
Any sample configs, or possible a link to a how to to get this setup? I was going to use FreeBSD to do the routing, but a appliance based Cisco router is much more attractive of an option to me.
we've had an issue with our network, we have 2 6509 connected with redundancy, which are connected with 2 x 4900 Switches, from which are connected to a ESX Chassis for visualization, the thing is that the ESX stopped working, and the 4900 switches, and the main core were suffering from overload, they hang on it very well, in order to stop the overload, one of the links to the ESX Chassis were disconnected from one of the 4900 switches. The CPU usage from the 4900 and the core(6509) went down below 40%, and then they started to migrate the virtual servers from the chassis to another 2 chassis that were added right after. They were actually working well, but suddenly the 6509 changed to the other supervisor after everything was OK. We were wondering what could have been the cause of this, maybe the virtual servers migrations, maybe the overload from the ESX ? We also had a few question, is there any need to reload the cores every few months as a planned task ? Because the cores have been up for more than 1 year. And also is there any kind of of tool to monitor the CPU status, or the status overall from the cores or the switches ?
View 3 Replies View RelatedThe have around 80 staff and I think the current infrastructure is overkill for the size of the company. The current kit is old and they have no GB ethernet ports. They currently have:-
Core Switch:
1x Cisco c6509with a 48 port fast ethernet module (WS-X6248-RJ-45)
and an 8 port fibre module (WS-X6408A-GBIC)
I'm looking to replace this with something with 72 ethernet ports and 8 fibre ports
Access Switches:
2x 3500Replacement needs at least 48 ports and 2 fibre modules each
and 2x 5500Replacement needs at least 72 ports and 2 fibre modules each.
If client gateway = 192.168.64.9 then next-hop = 192.168.64.8 else use default-route 0.0.0.0
I know it's possible to do a route-map match ip-address ACL list. But is it possible to match on gateway?
Some info about hardware and config:
6509-E in VSS (IOS 12.2(17r)SX5) withVS-S720-10G supervisor.
All routes are static, IP for 192.168.64.9 is on SVI vlan.
I have two ISPs. Each is on it's own subnet connected to the 6509 MSFC/Switch. FW1 is on 100.1.100.0/30 and FW2 is on 200.1.200.0/30 subnet. My goal is route all traffice going to the Internet from subnet 10.133.3.0/24 to FW1 and all other subnets across the organization to FW2. I am not sure if I need to use ACL / Static route combo, or just a static routes or ACLS?
View 5 Replies View RelatedWe have a Catalyst 6509 switch, and we hope to use policy based routing to redirect http traffic to my proxy server, where I can find the configuration example?
View 11 Replies View RelatedI would like to ask you if it's possibile to block routing between some Vlan for just once of them.
Maybe I can explain better:
I've got a Cisco 6509 with 4 configured vlan interfaces
Int Vlan 10 10.10.1.0/24
Int Vlan 20 10.10.2.0/24
Int Vlan 30 10.10.3.0/24
Int Vlan 40 10.10.4.0/24
Vlan "10" is the phone voip Vlan and it must not talk with the others Vlan. The others Vlan can comunicate normally except with Vlan "10".
Pratically Vlan "10" needs to be isolated from the others.
This equirement comes becouse Vlan 10 is wireless and has the WEP key encryption (very weak protocol). Some Phone couldn't support the WPA2 key and I need to avoid an unauthorized external client, cracking the WEP key and connecting to this WiFi, could have free access to the others Vlan.
I have a problem on my catalyst 6509 on which I would like to do the following things :
I have some Vlans in which multicast is enabled.
In tose Vlan theres is a router which is default router for equipements.
I had enabled multicast routing because some Vlan needs to exchange multicast informations, but I wolud like to make difference between Multicast traffic. For example I have 5 vlans:
Vlan 1 and 2 need to exchange Multicast informations but the don't need multicast information from Vlan 3 and 4
Vlan 3 and 5 need to exchange Multicast informations but the don't need multicast information from Vlan 1 and 2
Vlan 5 is independant Vlan but doesn't need to have multicast information from all others vlan.
Last problem, equipement on differents vlan can use the same Mulkticast group address. In this case, Multicast routing is not working between Vlan 1 to Vlan 2 and Vlan 3 to Vlan 4.
I need to setup my 6509 with PBR going to two different Firewalls. The 6509 has vlans and multiple serial interfaces. What/where do I install the policy-maps? I want to direct one of the vlans to one firewall and the other vlans and wan subnets to the other firewall.
View 26 Replies View RelatedI am migrating from Cisco 6509 IOS (12.2) to Nexus 7000 NX-OS (5.1(1)).I am looking for a equivalente NX-OS command for permit ipinip on IOS.
View 2 Replies View RelatedI have 2 6509-E chassis with SUP-720-VSS and classic line cards :-(. on October 2011 the switch reached 100% CPU on both devices and the entire network went down. Customer restarted the core so we lost all the log files and couldnt find out any root cause on the same. TAC engineer suggested to have some script configured on the system in case of CPU shooting up above 70%, it will create a file in flash and keep appending the logs to the same. Last week i got call from customer saying that the CPU again went high for around a minute on both the cores. Last time i added CoPP also on the switch in order to prevent the CPU reaching 100%. Still it went high and from the captured logs i saw that the process created the high CPU was Port Manager Per and SSH process. Attached the file created by the netdr capture command.
View 1 Replies View RelatedI have a customer that has a Catalyst 6509 with two Supervisor VSS capable and my Sales team sell another 6509 with just one Supervisor VSS capable. Simple question: Will VSS configuration will recognize that I have three Supervisors? It will work as QUAD-SUP solution or as a normal VSS solution?
View 7 Replies View RelatedWe are trying to migrate from 1g to 10G, couldn't find any module on 6509-E which supports 10G on SFP+ ...I can see X2 and Xenpacks .. but not SFP + .what exactly this Xenpack means ?
View 3 Replies View RelatedWe have connected a single F5 box with dual links to 2 different Cisco Catalyst switches using 802.1Q trunks. F5 is configured with RSTP mode and on Cisco Switch RPVST+ is configured.STP root bridge is hardcoded on the Cisco side. Loop Guard is globally enabled.On F5 STP link type is Auto, STP Edge port is disabled since that port is connected to the cisco switch.When we are failing over the F5 primary link to the secondary link we see 'Loop Inconsistent' on the cisco switch and things dont work after the failover.We have tried configuring the F5 as STP passthrough but that doesn't fix out the issue.I have checked out the forums and found out following recommendations
1. Configuring MSTP bw F5 and Cisco for better compatibility (Not possible from Cisco side because of a major change in large production setup)
2. Configuring VSS in Cisco switches (not possible due to hardware limitation)
3. Connecting F5 using single links to each switch (redundancy compromised)
I am wondering that on which default vlan does the F5 STP instance0 sends the STP BPDUs ? the term used on Cisco side is native vlan and others use PVIDs; that F5 default vlan should match the native vlan on cisco trunk side.
Tonight we were performing an IOS upgrade on our 6509 VSS to 122-33.SXI6. Both 6509's have dual Supervisor cards installed. Initially we had problems with switch 2 slot 5 supervisor returning to rommon however switch 2 slot 6 supervisor loaded correctly. After manually setting the boot var in rommon, switch 2 slot 5 supervisor reloaded correctly.
After all supervisor's were online we noticed when looking at " show switch virtual redundancy" that sw 1 & 2 slot 6 supervisors were running the correct IOS version but sw 1 & 2 slot 5 were running different IOS versions, however when looking at the show version we are running on the upgraded IOS??? See output below...
Why the active supervisor has loaded the incorrect IOS the VSS is running on the upgraded IOS? I have verified the IOS was copied correctly to each supervisor bootdisk, I see no issues.
My Switch Id = 1 Peer Switch Id = 2 Last switchover reason = none Configured Redundancy Mode = sso Operating Redundancy Mode = sso
Switch 1 Slot 5 Processor Information :----------------------------------------------- Current Software state = ACTIVE Uptime in current state = 3 hours, 38 minutes Image Version = Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXI9, RELEASE SOFTWARE (fc2)Technical Support:
[code].....
We are looking to avoid the need to install an additional device in our network as our core 6509s are not being pushed by any stretch. However, we are having an issue getting the 6509 to assign DHCP addresses and perform NAT.
Most interfaces and V LAN's on the 6509 are using public IPs and have BGP routing at the edge. We have a trunk up link coming into the 6509 on a ws-6816 card via a SMF GBIC in slot 9, port 2 that feeds a wifi link where we are looking to provide guest access to our network.
We created 2 V LAN s on the switch 20 and 21. We assigned a private IP and network to the VLAN20 interface and assigned a new public /30 sub net ip to the V LAN 21 interface. The following configuration was applied which I thought was the required configuration based on how we would typically configure ISR routers for the same services...
ip dhcp excluded-address 10.200.200.1
!
ip dhcp pool WiFi_Pool
network 10.200.200.0 255.255.255.0
default-router 10.200.200.1
dns-server 4.2.2.1 4.2.2.2
[ code]...
What am I missing in this configuration? Note that if I create an access switch port for v LAN 20 on the switch and plug a laptop in directly to the 6509, the laptop is unable to receive a DHCP address. If I assign the laptop an address in the 10.200.200.0 /24 range manually, I can ping 10.200.200.1 from the laptop, however, the laptop will not get to the internet as it appears to be failing to perform nat.