Cisco Switching/Routing :: 6509-E VSS Will Upgrade Rewrite The Configuration
Jan 22, 2013
I am planning on upgrading my 6509s to use VSS within the next few weeks. I have checked all of the hardware and software prerequisites, and we are good to go from that perspective.I do have more of a procedural question- my switches are already configured and in production, VLANs, HSRP (3 IP addresses per VLAN- 1 per switch plus virtual IP), etc. Does the VSS upgrade take all of this into account and rewrite the configuration correctly, or should I plan on redoing the entire config for the switches after the upgrade?
View 6 Replies
ADVERTISEMENT
Nov 21, 2011
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3
I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis?Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
View 2 Replies
View Related
Nov 21, 2011
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3.I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis. Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
View 2 Replies
View Related
Jul 17, 2012
I am position to migrate from CatOS 6509 switch to native IOS 6509 switch. long time ago, there was some site to convert automatically based on copy and paste onto the tool, but i can not find.
Does anybody know how to convert CatOS configuration to Native IOS configuration ? It is not IOS change, but it is configuration convert.
View 1 Replies
View Related
May 15, 2012
Tonight we were performing an IOS upgrade on our 6509 VSS to 122-33.SXI6. Both 6509's have dual Supervisor cards installed. Initially we had problems with switch 2 slot 5 supervisor returning to rommon however switch 2 slot 6 supervisor loaded correctly. After manually setting the boot var in rommon, switch 2 slot 5 supervisor reloaded correctly.
After all supervisor's were online we noticed when looking at " show switch virtual redundancy" that sw 1 & 2 slot 6 supervisors were running the correct IOS version but sw 1 & 2 slot 5 were running different IOS versions, however when looking at the show version we are running on the upgraded IOS??? See output below...
Why the active supervisor has loaded the incorrect IOS the VSS is running on the upgraded IOS? I have verified the IOS was copied correctly to each supervisor bootdisk, I see no issues.
My Switch Id = 1 Peer Switch Id = 2 Last switchover reason = none Configured Redundancy Mode = sso Operating Redundancy Mode = sso
Switch 1 Slot 5 Processor Information :----------------------------------------------- Current Software state = ACTIVE Uptime in current state = 3 hours, 38 minutes Image Version = Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXI9, RELEASE SOFTWARE (fc2)Technical Support:
[code].....
View 3 Replies
View Related
Jan 15, 2012
Will I be OK doing a eFSU Upgrade from s72033-ipservicesk9_wan-mz.122-33.SXI2a to s72033-ipservicesk9_wan-mz.122-33.SXJ1?
I only have a single supervisor in each chassis.
Should I be ok with just following the eFSU upgrade instructions in the below?
[URL]
View 1 Replies
View Related
Jan 9, 2013
I am going to upgrade the IOS image on 6509-E SUP 2T from 15.1 to s2t54-adventerprisek9-mz.SPA.150-1.SY3.bin switch and i would like to know whether i would need to upgrade the boot loader image as well.
View 4 Replies
View Related
Sep 9, 2012
I have a 6509 switch with SSO Redundancy (STANDBY HOT) with IOS ver 12.2(17d)SXB11, RELEASE SOFTWARE (fc1) (c6k222-jk9sv-mz.122-17d.SXB11.bin). I need to upgrade the IOS on this switch.I have 512MB Memory on the switch and 40144896 bytes free on Disk0.which IOS is the latest version to upgrade and also give me some hints for IOS upgrade on this switch?
View 7 Replies
View Related
May 14, 2013
I would like to find out how to upgrade SUP engine 32 via USB port as I've never did IOS upgrade on a SUP engine via USB before
View 5 Replies
View Related
Nov 19, 2012
I have 2 6509 switches configured with VSS.As per advised my managment I have to enable SSH but it is not available existing IOS which is "s72033-ipbase-z.122-33.SXI3.bin". SSH available in "s72033-ipbasek9-mz.122-33.SXI10".
upgrade the IOS with VSS configured switches.
View 9 Replies
View Related
Oct 16, 2012
We are trying to upgrade the IOS on one of our 6509 switches. We have two 720 10GE supervisors running in SSO. Our procedure is reload the standby supervisor with the new IOS. We understand that you can only use one console connection when in RPR mode so we rely on the active supervisor giving us information that the standby unit is up and running.
The problem we have is that when we do a "show Module" on the switch the online diagnostics for the standby supervisor comes back us unknown. [code] We believe the active supervisor can see the standby supervisor because when we save the configuration we get a message saying that the config is sync'd with the standby router. We have a TAC case raised to investigate. We are upgrading from 12.2(33) SXI1 to 12.2(33) SXJ3
View 1 Replies
View Related
Oct 8, 2012
We are planning to upgrade the IOS on our two 6509E supervisors in the next few weeks. We currently run IOS 12.2(33) SXI1 and are upgrading to 12.2(33) SXJ3. At the moment the two supervisors are in SSO mode and after reading many articles it says that when the images are different on the two supervisors they are in RPR mode. When you then reload the active supervisor it will reboot all the line cards.
1. Is above correct? Will my line card reload?
2. We also have a FWSM installed, When/If the line cards are rebooted does the FWSM also reboot?
View 1 Replies
View Related
Sep 18, 2012
I am going to upgarde SUP2 to SUP32 on my 6509 by next week. right now I have 2 SUPs on the 6509 in redundant mode.
View 5 Replies
View Related
May 1, 2013
we have some pairs of 6509-VSS, which partially have old (no more officially supported) 6509-Chassis.All linecards in the VSS are the same (Sup 720-10GE-3C, 67XX).
We now bought some new 6509-E-Chassis and want to change the old chassis by the new ones in a ISSU manner, that means:
1. putting the partner, which chassis changes, in redundancy mode, switch it off, exchange chassis (old "Catalyst 6509", new "Catalyst 6509-E")
2. inserting the line-cards exactly in the same slots and connecting all cables
3. switch on the new chassis, witing to come up in VSS
I'm not sure of having to set the switch number for VSS (is that in the Sup?; configuration? or part of the chassis-memory?)
I've looked up cisco for some hints, but don't found anything.
View 5 Replies
View Related
Dec 12, 2012
I have ROM MON version 12.2(17r)S2 and I am trying to determine if I need to chnage this to 12.2(17r)SX7. It does not appear I need to with the upgrade to 12.2(33)SXI10. Is this correct?
View 1 Replies
View Related
Oct 7, 2012
I need to upgrade 2xsup2 module to 2xsup32 on my cisco 6509. I just found out that I can not have the CISCO WS-X6500-SFM(Cisco Switch Fabric Module switch) with Sup32 and I have to remove 2 xCISCO WS-X6500-SFM2 modules from the switch.I am using this switch as a access switch and most of the ports are 100Mbps.
let me know if the upgrade would be safe or not as far as the bandwidth?
View 2 Replies
View Related
Jun 21, 2012
I support an active VSS cluster using 2 x 6509E chassis with single Supervisor 3C modules in each chassis. I want to replace these with Supervisor 2T modules. All my service modules and line cards are supported with the Sup2Ts (I will also be implementing 6908 modules). Is there a document on the Cisco site for this? I haven't found one though I can find plenty that describe how to do a software upgrade.
(Note, I have a 3rd (non VSS) 6509E chassis that is also part of this core network and that will maintain VTP/V LAN's etc).
View 9 Replies
View Related
Jan 20, 2011
I currently have this in our Sup720:
boot system flash bootflash:s72033-jk9o3sv-mz.122-17a.SX3.bin
boot bootldr sup-bootflash:s72033-psv-mz.122-17a.SX1.bin
I downloaded s72033-mp001-pz.122-33.SXH5
I read the documentation on Upgrading Software Images on Catalyst 6000/6500 Series SwitchesURL
I was wondering do I copy the s72033-mp001-pz.122-33.SXH5 to the sup-bootflash and bootflash? In the example it also uses disk0: but I get a <No device available>. Also keep in mind we're upgrading the application and maintanence partitions also. So this is a big upgrade and I've never done this before.
I guess the 2 things I want to know is:
1) Can I copy the s72033-mp001-pz.122-33.SXH5 to both the sup-bootflash and the bootflash? Can I run it just copying it to the sup-bootflash?
2) It was my understanding that I only needed one image file for the upgrade but the documentation says I need
"a. the main software image
b. the bootloader image"
Do I need another file? I'm a little confused. I did notice the files had different names and sizes and so do the ones on my current Sup 720.
And we are doing this tomorrow and I just happened to be reviewing the documentation one more time and somehow missed this.
View 8 Replies
View Related
Jan 10, 2012
Any sample qos configuration that is enabled on a 6509 for voip ? it would be nice if its a auto-qos . I do not have an available 6509 to try this.
View 2 Replies
View Related
Sep 30, 2012
I have 2 6509 chasis with one SUP720-3B in each and current IOS is s72033-ipservicesk9_wan-mz.122-18.SXF4 and 2 FWSM with version is 3.3.1 I need to upgrade FWSM system software to 4.1, after checking FWSM 4.1 release notes, I thought of upgrading IOS to latest version to 12.2(33)SXJ.I got new 2 CF of 512MB and downloaded the new IOS on them and need to upgrade 6509 IOS first to meet the requirement for FWSM upgrade.
View 1 Replies
View Related
Jun 17, 2012
After a abrupt power cylce of 6509 switch, vlan configuration got missing. Switch has not crashed.
View 4 Replies
View Related
Feb 2, 2013
I am planning to upgrade the current core switch(3750) to 6509 series switch. Since we have a production network running we have to plan for an online core switch upgrade.
View 7 Replies
View Related
Jul 16, 2012
How do I find out who made the last configuration change on a 6509 CAT switch with the following Show VER
WS-C6509 Software, Version NmpSW: 8.5(9)
Copyright (c) 1995-2007 by Cisco Systems
NMP S/W compiled on Apr 16 2007, 21:23:23
[Code].....
View 5 Replies
View Related
Dec 1, 2011
I came across a Catalyst 6509 switch configuration and have noticed some strange thing on the ether channel configuration side, it appears that it have interface port-channel 2 and port-channel 2A, what was that mean? its the ether channel not forming and joined together?
What wrong with the below configuration that cause it to automatic created another port-channel (2A) interface in this case?
[code]...
View 3 Replies
View Related
Mar 13, 2012
Last night I've upgraded a catlyst 6509 (non-redundant), during the upgrade I# run into the problem that the 6509 only wants to boot from sup-bootflash, and that it took an old image from sup-bootflash.I deleted this old image and then the node came into rommon mode.There I did the boot command and refered to the correct image on disk1:Now the boot succeeded. Just in time before I run out of my maintenance window.
I did some investigation and looked into the supervisor (using attach 5 and remote command switch show boot) and detected that it's configuration register is on 0X2101 (This is because I run into problems a week ago because of a corrupt flash disk and changed this in rommon mode , without changing it back, I'm afraid I'm not totally known with the 6509)
Question is now how can I change the configuration register back to 0x2102 without any service interruption (It will cost me quit some goodwill if I have to boot the node for the third time in three weeks)?
View 3 Replies
View Related
Mar 9, 2013
We recently installed Cisco 6509-E with dual Sup 720-BXL. We are using this switch on internet Edge. Internet connection is terminating on 10GIG fiber port.We do have following line cards installed.
1. 10 GIG * 4 port line card
2. 1 GIG * 8 port line card
3. Empty
4. Empty
5. Sup 720-3BXL
6. Sup 720-3BXL
7. 1 GIG * 48 ports
8. 1 GIG * 48 ports
9. 1 GIG * 48 ports
We do have 2 GB internet pipe.We are running load test sending http port 80 request and when load reach to arround 100 to 200 mbps and connections from out side to inside 80,000 switch start reponding very very slow and start packet loss and when I try to ping from one server to second server it show normal ping but if I tried to ping gateway IP of server which is SWITCH IP it show packet loss and very high letancy.
Switch also throw message "No memory available: Update of NVRAM configuration failed"
View 7 Replies
View Related
Nov 15, 2012
I have 1x Cisco 6509 with Sup2 and MSFC2 and it is running on IOS (c6k222-jk9sv-mz.122-17d.SXB11). I have following policy map :
Policy Map VOIP
Class IP PHONE
priority percent 75
and the following command on each interface: service-policy output VOIP those configuration are working fine on SUP2 with MSFC2 but last week I tried to upgrade the SUP2 to SUP32 on the switch and upgrade the IOS to the latest version (s3223-adventerprisek9-mz.122-33.SXJ4) but when I try to put service-policy output VOIP on each physical interface I am getting the following error:
"Priority command is not supported in output direction for this interface" and when I try to add service-policy output VOIP on a V LAN interface I am getting following error:
MQC features are not supported in output direction for this interface. Will I need to change something after upgrading to SUP32..
View 3 Replies
View Related
Feb 24, 2013
I have a two fiber connection from our Central Office(6513) to Remote office (6509). I have a requirement that on the remote office if one of the fiber goes down, the second fiber should work as a failover. I am planning to use SUP720-3B SFP to connect to the CO.
Can I connet one fiber to Sup720-3b G5/1 & another fiber connection to G5/2? or Can I connet one fiber to Sup720-3b G5/1 & another fiber connection to G6/2? I am running EIGRP between sites. Any sample config.
sup-bootflash:s72033-pk9sv-mz.122-18.SXD7b.bin"
View 4 Replies
View Related
Jan 11, 2012
we've had an issue with our network, we have 2 6509 connected with redundancy, which are connected with 2 x 4900 Switches, from which are connected to a ESX Chassis for visualization, the thing is that the ESX stopped working, and the 4900 switches, and the main core were suffering from overload, they hang on it very well, in order to stop the overload, one of the links to the ESX Chassis were disconnected from one of the 4900 switches. The CPU usage from the 4900 and the core(6509) went down below 40%, and then they started to migrate the virtual servers from the chassis to another 2 chassis that were added right after. They were actually working well, but suddenly the 6509 changed to the other supervisor after everything was OK. We were wondering what could have been the cause of this, maybe the virtual servers migrations, maybe the overload from the ESX ? We also had a few question, is there any need to reload the cores every few months as a planned task ? Because the cores have been up for more than 1 year. And also is there any kind of of tool to monitor the CPU status, or the status overall from the cores or the switches ?
View 3 Replies
View Related
Apr 11, 2012
The have around 80 staff and I think the current infrastructure is overkill for the size of the company. The current kit is old and they have no GB ethernet ports. They currently have:-
Core Switch:
1x Cisco c6509with a 48 port fast ethernet module (WS-X6248-RJ-45)
and an 8 port fibre module (WS-X6408A-GBIC)
I'm looking to replace this with something with 72 ethernet ports and 8 fibre ports
Access Switches:
2x 3500Replacement needs at least 48 ports and 2 fibre modules each
and 2x 5500Replacement needs at least 72 ports and 2 fibre modules each.
View 13 Replies
View Related
Feb 26, 2012
If client gateway = 192.168.64.9 then next-hop = 192.168.64.8 else use default-route 0.0.0.0
I know it's possible to do a route-map match ip-address ACL list. But is it possible to match on gateway?
Some info about hardware and config:
6509-E in VSS (IOS 12.2(17r)SX5) withVS-S720-10G supervisor.
All routes are static, IP for 192.168.64.9 is on SVI vlan.
View 3 Replies
View Related
Mar 6, 2012
I have two ISPs. Each is on it's own subnet connected to the 6509 MSFC/Switch. FW1 is on 100.1.100.0/30 and FW2 is on 200.1.200.0/30 subnet. My goal is route all traffice going to the Internet from subnet 10.133.3.0/24 to FW1 and all other subnets across the organization to FW2. I am not sure if I need to use ACL / Static route combo, or just a static routes or ACLS?
View 5 Replies
View Related
May 29, 2012
We have a Catalyst 6509 switch, and we hope to use policy based routing to redirect http traffic to my proxy server, where I can find the configuration example?
View 11 Replies
View Related
