Cisco Switching/Routing :: Find A Sample Working Configuration Of (HP Rebadged) 3120 Blade Switch?
Jun 13, 2012
Where can I find a sample working configuration of (HP rebadged) 3120 Blade Switch?
I have the Cisco 6500 end configured as follows:
interface Port-channel1
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,300,304,310,320,560-562,600,740,770,950
switchport mode trunk
load-interval 30
[code]....
I will be connecting 9/5 and 9/6 to Cisco 3120G (HP rebadged) Blade Switch in c-Class Enclosure tomorrow.It would be nice to have a rough sample configuration of the above 3120G switch.
View 5 Replies
ADVERTISEMENT
Mar 17, 2013
I received 3 GESM cisco blade switches for a HP Blade system. I do not have the chassis. I need to sanitize these blade switches but I have never worked with these. I don't see any removable flash. Where is the config stored?
View 7 Replies
View Related
Jan 10, 2012
Any sample qos configuration that is enabled on a 6509 for voip ? it would be nice if its a auto-qos . I do not have an available 6509 to try this.
View 2 Replies
View Related
Oct 21, 2012
I have vm with 2 nic card and 2 blade switch 3120g in the same hp c7000 blade enclosure. How to setup etherchannel as highlight in attachment ?
View 4 Replies
View Related
Mar 28, 2011
I have a Cisco Catalyst 4507R+E (with Sup7-E) and two blades; one WS-X4748-RJ45V+E and one WS-X4648-RJ45-E.
When I connect a device to a port on the WS-X4748-RJ45V+E blade the port will not come up, show interface shows the status as "notconnect". When I connect the same device to the WS-X4648-RJ45-E blade the interface comes up.
The WS-X4748-RJ45V+E blade seems to have initialised okay, it appears in the output of "show module" as OK.
I get exactly the same effect on a second, identically configured Catalyst 4507R+E.
The software version is IOS XE 3.1.0SG, which according to the release notes supports the WS-X4748-RJ45V+E blade
View 2 Replies
View Related
Apr 16, 2012
i have one of my switch modules that shows PwrDown when i issue the command show mod.
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 9 Supervisor Engine 32 8GE (Active) WS-SUP32-GE-3B SAD09120263
2 48 48 port 10/100/1000mb EtherModule WS-X6148-GE-TX SAL1029VWZ5
[Code]....
i tried disabling the diagnostic monitor for the module, did a power enable module command and then reset it but it still fails. this is the third blade that i am replacing in a few weeks and i still get the same error. i am persuded that it is not a hardware since it is the third blade in a matter of weeks. after the module reset, i receive this error % module 3 is operationally off (FRU-power failed)
could an ios upgrade solve this issue? are there any ios related bugs?
View 10 Replies
View Related
Nov 14, 2011
3750 switch connects to Blade-switch_1 and Blade-switch_2 Spanning-tree mode is configured as rapid-pvst on 3750 switch, do I need to configure rapid-pvst on both blade-switches or keep the default pvst config.3750 is running VTP domain HQ and transparent mode Both Blade_switches are running VTP domain CLI and transparent mode To configure Etherchannel between 3750 and blade-switch_1 do I need to have all devices in same vtp domain?
View 16 Replies
View Related
Aug 6, 2012
I try to connect a cisco blade switch 3020 to Nexus 2232 with etherchannel, but when I connect the second link a obtain flapping on vlans. [code] why the vlans are flapping ? it's something wrong on the config ? [code]
View 7 Replies
View Related
Jul 27, 2011
I have 6 of these WS-CBS3012-IBM modules that need to be configured but I cannot access the USB console port. I was told I could just get any DB9- to- USB cable and that would work. I did buy a DB9-to-USB cable and it did not work. I looked up the installation guide for this module and it just said the console cable is DB9-to-USB but with no part number.
View 3 Replies
View Related
Apr 30, 2012
show logging
May 1 16:00:30: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to down
May 1 16:00:39: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to up
May 1 16:17:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to down
May 1 16:17:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to up
May 1 16:25:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to down
May 1 16:25:37: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to up
May 1 17:19:25: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to down
Configuration as below:
macro name vmware
switchport trunk encapsulation dot1q
switchport mode trunk
no switchport access vlan
[code].....
Note:Both active blade switch and standby one are connecting to same aggregate switch 3750. Yet the active one, with same config as standby one, has not occurred this issue.
View 2 Replies
View Related
May 30, 2011
I'm having trouble getting Tacacs+ to work correctly with ACS5.1 and a simple catalyst 3750 switch.I can authenticate with AAA, however i cannot get a single command to work once i'm in; "Command authorization failed" even on "enable".
Any useful resource that will walk me through the process?
View 3 Replies
View Related
Nov 20, 2009
I have a Catalyst 4006 switch in production and a spare switch of same model. I have to quickly copy the configuration from production switch to spare switch (both L2 and L3 configurations) How do I do that?
View 6 Replies
View Related
Sep 5, 2012
I have a /25 block of public ips from my ISP which I'd like to subnet into two /26 blocks. I have a Cisco 2600 with 2 ethernet ports in it. What are the commands I'd need to take my 200.180.200.0 255.255.255.128, gateway 200.180.200.1 and turn it into 200.180.200.0 255.255.255.192, gateway 200.180.200.1 and 200.180.200.64 255.255.255.192, gateway 200.180.200.65? One of the interfaces will be connected to the ISP & the other to a switch, and then we could access the two subnets through the switch.
View 6 Replies
View Related
Sep 22, 2011
sample configuration for internet failover . i have 2 ISPs with one coming in thought a serial cable and another through internet and would wish one take over after the other has failed .The router is Cisco 1921 .
View 4 Replies
View Related
Mar 18, 2013
Any sample configuration of c1310 as a work group bridge.
View 2 Replies
View Related
Jul 16, 2012
How do I find out who made the last configuration change on a 6509 CAT switch with the following Show VER
WS-C6509 Software, Version NmpSW: 8.5(9)
Copyright (c) 1995-2007 by Cisco Systems
NMP S/W compiled on Apr 16 2007, 21:23:23
[Code].....
View 5 Replies
View Related
Apr 26, 2012
I'm trying to find a document in Design Zone about configuring a Wireless AP and I wasn't able to find it. I have a good experience configuring switches, routers and firewalls in CLI and this is the first that I have my hands on APs (1240 AG).
View 2 Replies
View Related
Apr 2, 2012
If i replace a card of the same type in the same slot will I lose the configuration for that card or does it live in the backplane of the device?Is there any special command I need to run to replace the card or can i shutdown the 4507r-e and just swap out the blade?
View 3 Replies
View Related
Feb 10, 2013
We have 12 Catalyst Blade Switches 3020 for HP running IOS Version 12.2(55)SE. In the configuration of these switches I see the statement shown below.
no spanning-tree vlan 34,45-55,70,600,643,840,843-850
The 12 blade switches are configured as VTP clients and running VTP V2. I did not configure the statement shown above. It appered by itself. And even if I delete it, it will reapper. (The blade switches are interconnected to two 6509s. The two 6509s are the STP root and VTP bridges. I configure Vlans and STP on the 6509s).
why the statement above appers on the blade switches 3020s?
I mean I use other Cisco switches such as 3750s and 3560s and I have never seen the statement above appear by itself.
View 4 Replies
View Related
Nov 18, 2012
Im having problems changing a connection between a Cisco3560 and Cisco IBM Blade switch 3012 actually the configuration is access in Cisco 3560 and trunk int Cisco 3012 when i change the connection to trunk i lose conecctivity to the servers connected in the 3012, i have changed the access from vlan 1 to the respective vlan in the access port of the servers
View 5 Replies
View Related
Dec 29, 2011
Looking at the specs for WS-X6704-10GE, it shows the port buffers at 16M per port. This doesn't seem like very much for a 10G port. Is this upgradable or related to how much RAM is in the blade?
View 4 Replies
View Related
Oct 2, 2011
we have a 6509 with ios 12.2.33SXJ
we have 2 WS-X6516-GE-TX, WS-X6516A-GBIC, and a WS-X6748-GE-TX with a WS-F6700-CFC daughtercard
our sup is a WS-SUP720-3B
we are experiencing packet loss for everything connected in the WS-X6748-GE-TX blade, right now we dont have any production device in that blade due to the packet loss we are experiencing.
this switch was running hybrid before it is now running native ios, however I can't recall if we didn't have that packet loss before. do i need to update a firmware of the card or daughtercard (if this is possible, can't say i've done it before).
View 10 Replies
View Related
May 3, 2010
I have a LAP-1142 connected to one of our PoE blade in our 4506 switch, it used to work fine with the following power consumption:
Interface Admin Oper Power(Watts) Device Class From PS To Device --------- ------ ---------- ---------- ---------- ------------------- -----
Gi4/3 auto on 21.5 20.0 AIR-AP1252AG-A-K9 3
However, we had power issue on Apr 28, so it failed and we saw from the log below:
Apr 28 13:57:38.990: %C4K_ETHPORTMAN-3-INLINEPOWEROVERDRAWN: Inline powered device connected on port Gi4/3 exceeded its hardware protection threshold.Apr 28 13:57:39.694: %PM-4-ERR_DISABLE: inline-power error detected on Gi4/3, putting Gi4/3 in err-disable state After the power restored later, the other LAP connecting with the same blade restored without any problem, except this one:
Interface Admin Oper Power(Watts) Device Class From PS To Device --------- ------ ---------- ---------- ---------- ------------------- -----
Gi4/3 auto on 16.6 15.4 Ieee PD 3
View 13 Replies
View Related
Feb 12, 2013
- Incoming frames on three of a blade's four switchports are being put into VLAN 1 even though the ports are either in other access VLANs, or are configured as trunks with different VLAN IDs being tagged by the server. - When the ports go down the access VLAN is removed from the port.
Switch stack: 4x WS-CBS3120X-S, 12.2(58)SE1
HP blade: HP BL460c Gen8
This combination has been used successfully elsewhere.
Switchport configuration:
!
interface GigabitEthernet1/0/13 -------> THIS PORT IS OK
switchport mode trunk
[Code].....
View 1 Replies
View Related
May 11, 2013
I'm trying to get the VFC up in B22-FEX blade in Dell which is connecting to Nexus 5596UP.
The message I get is
# sh int vfc1033
vfc1033 is down (Error Disabled - VLAN L2 down on Eth interface)
Bound interface is port-channel3
Hardware is Ethernet
Port WWN is 24:08:00:2a:6a:0d:db:3f
Admin port mode is F, trunk mode is on
[code]....
View 3 Replies
View Related
Jan 2, 2013
I have one switch 3750G12S I joined the company new, I found that they want to replace it with Alcatel stack switches. I didnt configure this Cisco switch before. how to configure it. I have 4 other new cisco switches in the topology which is not created yet. the 4 switches are all 2960.
View 17 Replies
View Related
May 21, 2013
i have floor with 10 users with DATA vlan and VOICE vlan , WIRELESS vlan , my questions :
Basement floor Core switch fiber -----> my floor switch <--------my internet DSL router827
- In this scenraio the switch in my floor will be as L2 or L3 ?
- What is the configuration it will be in the switch if it is L3 ?
- What is the configuration it will be in DSL router with Subinterfaces for each vlan ?
Any sample for configuration that can work for switch nad DSL router ?
View 3 Replies
View Related
Feb 6, 2012
I am trying to set up a simple configuration on a Cisco 4928-10G switch running
cat4500-entservicesk9-mz.122-37.SG.bin
All I want to do is to mark all trafic on vlan 3 let's say for this example with dscp af31.
All outgoing trafic to be marked with DSCP AF31.
In pratice If I have 2 laptops connected to access ports on vlan 3. When one laptop pings the other I want to see on the receiving end when I run wireshark the traffic to come marked with DSCP AF31.
View 1 Replies
View Related
May 21, 2013
I have a Cisco SG 300-20 as the core switch, layer 3. It is 192.168.4.6 on VLAN1 and 192.168.5.1 for VLAN2 (VOIP). All the ports are set in trunk mode. DHCP relay is setup on this switch.
The phones connected into a layer 2, Catalyst 2960-S switch. All ports are set in trunk mode. Default gateway on it is set to 192.168.5.1.
DHCP for both VLANs is provided by a Windows Server 2008 R2 server (the relay IP 192.168.4.15).
There is also an ASA 5510 in the mix which is 192.168.4.1. It has a route added to it for the 192.168.5.0 network to go to the SG 300 (192.168.5.1).
Just the two switches can ping each other on the 192.168.5.x network when I "add vlan 2" to the trunk port that is connected between the SG 300 and the 2960. The phones don't get DHCP on the 2960 switch. And I cannot ping 192.168.5.x from the ASA or anything else on the 192.168.4.x network.
After a bit of reading on intra-vlan routing for the SG 300 switch, I am thinking the SG 300 has to be the "center" of things so I need to make it 192.168.4.1 to be the gateway for both VLANs and change the ASA to 192.168.4.2 for VLAN1, etc. And I really can't do asymmetric routing with this switch.
View 1 Replies
View Related
Mar 18, 2013
I have a 3560 switch with 1 VLAN (VLAN 10) where I need to make ports:
1-10 as isolated (can't contact each other)
11-20 as community (need to contact each other like a normal VLAN)
23 as promiscuous (server that ports 1-20 need to get to)
24 as promiscuous (WAN router where ports 1-20 need to get to and the remote servers).
[Code]...
View 26 Replies
View Related
Jun 24, 2012
I am interested in learning and setting up VPN IPSec with Cisco ASA 5505. I've managed to successfully setup VPN andcan connect to it from outside and browse securely to the outside/internet via tunnel. However, once I am connected to VPN, I cannot access any of my internal hosts/servers via VPN client. I am wondering it its a missing ACL/NAT...ASA Version 8.2(5)
!
hostname ciscoasa
enable password xxxxxxxxxxx encrypted
passwd xxxxxxxxx encrypted
names
[code]....
View 1 Replies
View Related
Mar 7, 2013
I am having an issue bypassing a switch 3750G series. How i can bypass the old configuration in the switch.i have tried the CTRL+BREAK at startup but it wont work.
View 2 Replies
View Related
Aug 27, 2012
I am going to change a running 6500 switch. I am missing a best pratice doc for changing a cisco switch configuration. My question is if a startup-config has an error (due to typo mistake, or due to comands not supported on latest IOS) and I do copy tftp startup-config then what will happen ? I want to make sure when I do "reload" the switch then it should boot normally with the latest startup config !
View 3 Replies
View Related
