I received 3 GESM cisco blade switches for a HP Blade system. I do not have the chassis. I need to sanitize these blade switches but I have never worked with these. I don't see any removable flash. Where is the config stored?
View 7 Replies
Where can I find a sample working configuration of (HP rebadged) 3120 Blade Switch?
I have the Cisco 6500 end configured as follows:
interface Port-channel1
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,300,304,310,320,560-562,600,740,770,950
switchport mode trunk
load-interval 30
[code]....
I will be connecting 9/5 and 9/6 to Cisco 3120G (HP rebadged) Blade Switch in c-Class Enclosure tomorrow.It would be nice to have a rough sample configuration of the above 3120G switch.
I have vm with 2 nic card and 2 blade switch 3120g in the same hp c7000 blade enclosure. How to setup etherchannel as highlight in attachment ?
View 4 Replies View Related i have one of my switch modules that shows PwrDown when i issue the command show mod.
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 9 Supervisor Engine 32 8GE (Active) WS-SUP32-GE-3B SAD09120263
2 48 48 port 10/100/1000mb EtherModule WS-X6148-GE-TX SAL1029VWZ5
[Code]....
i tried disabling the diagnostic monitor for the module, did a power enable module command and then reset it but it still fails. this is the third blade that i am replacing in a few weeks and i still get the same error. i am persuded that it is not a hardware since it is the third blade in a matter of weeks. after the module reset, i receive this error % module 3 is operationally off (FRU-power failed)
could an ios upgrade solve this issue? are there any ios related bugs?
3750 switch connects to Blade-switch_1 and Blade-switch_2 Spanning-tree mode is configured as rapid-pvst on 3750 switch, do I need to configure rapid-pvst on both blade-switches or keep the default pvst config.3750 is running VTP domain HQ and transparent mode Both Blade_switches are running VTP domain CLI and transparent mode To configure Etherchannel between 3750 and blade-switch_1 do I need to have all devices in same vtp domain?
View 16 Replies View RelatedI try to connect a cisco blade switch 3020 to Nexus 2232 with etherchannel, but when I connect the second link a obtain flapping on vlans. [code] why the vlans are flapping ? it's something wrong on the config ? [code]
View 7 Replies View RelatedI have 6 of these WS-CBS3012-IBM modules that need to be configured but I cannot access the USB console port. I was told I could just get any DB9- to- USB cable and that would work. I did buy a DB9-to-USB cable and it did not work. I looked up the installation guide for this module and it just said the console cable is DB9-to-USB but with no part number.
View 3 Replies View Relatedshow logging
May 1 16:00:30: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to down
May 1 16:00:39: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to up
May 1 16:17:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to down
May 1 16:17:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to up
May 1 16:25:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to down
May 1 16:25:37: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to up
May 1 17:19:25: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to down
Configuration as below:
macro name vmware
switchport trunk encapsulation dot1q
switchport mode trunk
no switchport access vlan
[code].....
Note:Both active blade switch and standby one are connecting to same aggregate switch 3750. Yet the active one, with same config as standby one, has not occurred this issue.
I have several Cisco 2811 ISR Routers that are functioning as CallManager MGCP voice gateways. These routers have prtial PRI's attached to them which I realize are not supported by Cisco CallManager using MGCP. The problem is that whenever the router gets rebooted, the configuration under Controller T1 ends up with the improper PRI Timeslots command and I have to go in and manually change it. Solution: I have developed smal text files for each router that contains all of the commends needed to get the chnage accomplished (you have to shut down things and remove lines elsewhere to be able to change the PRI Timeslots) and I just telnet to the router and cut and paste the commands into the router.However, I would like to store those files on the router in such a way that I could telenet to the router and then either somehow display the file and then copy/paste it in or possible have a file that could be run to make the changes. That way I could do the job quickly fram anyplace I could telnet to the router and not have to have the text files on the local machine.
View 1 Replies View RelatedI have a Catalyst 4006 switch in production and a spare switch of same model. I have to quickly copy the configuration from production switch to spare switch (both L2 and L3 configurations) How do I do that?
View 6 Replies View RelatedIf i replace a card of the same type in the same slot will I lose the configuration for that card or does it live in the backplane of the device?Is there any special command I need to run to replace the card or can i shutdown the 4507r-e and just swap out the blade?
View 3 Replies View RelatedWe have 12 Catalyst Blade Switches 3020 for HP running IOS Version 12.2(55)SE. In the configuration of these switches I see the statement shown below.
no spanning-tree vlan 34,45-55,70,600,643,840,843-850
The 12 blade switches are configured as VTP clients and running VTP V2. I did not configure the statement shown above. It appered by itself. And even if I delete it, it will reapper. (The blade switches are interconnected to two 6509s. The two 6509s are the STP root and VTP bridges. I configure Vlans and STP on the 6509s).
why the statement above appers on the blade switches 3020s?
I mean I use other Cisco switches such as 3750s and 3560s and I have never seen the statement above appear by itself.
Im having problems changing a connection between a Cisco3560 and Cisco IBM Blade switch 3012 actually the configuration is access in Cisco 3560 and trunk int Cisco 3012 when i change the connection to trunk i lose conecctivity to the servers connected in the 3012, i have changed the access from vlan 1 to the respective vlan in the access port of the servers
View 5 Replies View RelatedLooking at the specs for WS-X6704-10GE, it shows the port buffers at 16M per port. This doesn't seem like very much for a 10G port. Is this upgradable or related to how much RAM is in the blade?
View 4 Replies View Relatedwe have a 6509 with ios 12.2.33SXJ
we have 2 WS-X6516-GE-TX, WS-X6516A-GBIC, and a WS-X6748-GE-TX with a WS-F6700-CFC daughtercard
our sup is a WS-SUP720-3B
we are experiencing packet loss for everything connected in the WS-X6748-GE-TX blade, right now we dont have any production device in that blade due to the packet loss we are experiencing.
this switch was running hybrid before it is now running native ios, however I can't recall if we didn't have that packet loss before. do i need to update a firmware of the card or daughtercard (if this is possible, can't say i've done it before).
I have a LAP-1142 connected to one of our PoE blade in our 4506 switch, it used to work fine with the following power consumption:
Interface Admin Oper Power(Watts) Device Class From PS To Device --------- ------ ---------- ---------- ---------- ------------------- -----
Gi4/3 auto on 21.5 20.0 AIR-AP1252AG-A-K9 3
However, we had power issue on Apr 28, so it failed and we saw from the log below:
Apr 28 13:57:38.990: %C4K_ETHPORTMAN-3-INLINEPOWEROVERDRAWN: Inline powered device connected on port Gi4/3 exceeded its hardware protection threshold.Apr 28 13:57:39.694: %PM-4-ERR_DISABLE: inline-power error detected on Gi4/3, putting Gi4/3 in err-disable state After the power restored later, the other LAP connecting with the same blade restored without any problem, except this one:
Interface Admin Oper Power(Watts) Device Class From PS To Device --------- ------ ---------- ---------- ---------- ------------------- -----
Gi4/3 auto on 16.6 15.4 Ieee PD 3
- Incoming frames on three of a blade's four switchports are being put into VLAN 1 even though the ports are either in other access VLANs, or are configured as trunks with different VLAN IDs being tagged by the server. - When the ports go down the access VLAN is removed from the port.
Switch stack: 4x WS-CBS3120X-S, 12.2(58)SE1
HP blade: HP BL460c Gen8
This combination has been used successfully elsewhere.
Switchport configuration:
!
interface GigabitEthernet1/0/13 -------> THIS PORT IS OK
switchport mode trunk
[Code].....
I'm trying to get the VFC up in B22-FEX blade in Dell which is connecting to Nexus 5596UP.
The message I get is
# sh int vfc1033
vfc1033 is down (Error Disabled - VLAN L2 down on Eth interface)
Bound interface is port-channel3
Hardware is Ethernet
Port WWN is 24:08:00:2a:6a:0d:db:3f
Admin port mode is F, trunk mode is on
[code]....
I have a Cisco Catalyst 4507R+E (with Sup7-E) and two blades; one WS-X4748-RJ45V+E and one WS-X4648-RJ45-E.
When I connect a device to a port on the WS-X4748-RJ45V+E blade the port will not come up, show interface shows the status as "notconnect". When I connect the same device to the WS-X4648-RJ45-E blade the interface comes up.
The WS-X4748-RJ45V+E blade seems to have initialised okay, it appears in the output of "show module" as OK.
I get exactly the same effect on a second, identically configured Catalyst 4507R+E.
The software version is IOS XE 3.1.0SG, which according to the release notes supports the WS-X4748-RJ45V+E blade
I have one switch 3750G12S I joined the company new, I found that they want to replace it with Alcatel stack switches. I didnt configure this Cisco switch before. how to configure it. I have 4 other new cisco switches in the topology which is not created yet. the 4 switches are all 2960.
View 17 Replies View Relatedi have floor with 10 users with DATA vlan and VOICE vlan , WIRELESS vlan , my questions :
Basement floor Core switch fiber -----> my floor switch <--------my internet DSL router827
- In this scenraio the switch in my floor will be as L2 or L3 ?
- What is the configuration it will be in the switch if it is L3 ?
- What is the configuration it will be in DSL router with Subinterfaces for each vlan ?
Any sample for configuration that can work for switch nad DSL router ?
I am trying to set up a simple configuration on a Cisco 4928-10G switch running
cat4500-entservicesk9-mz.122-37.SG.bin
All I want to do is to mark all trafic on vlan 3 let's say for this example with dscp af31.
All outgoing trafic to be marked with DSCP AF31.
In pratice If I have 2 laptops connected to access ports on vlan 3. When one laptop pings the other I want to see on the receiving end when I run wireshark the traffic to come marked with DSCP AF31.
I have a 3560 switch with 1 VLAN (VLAN 10) where I need to make ports:
1-10 as isolated (can't contact each other)
11-20 as community (need to contact each other like a normal VLAN)
23 as promiscuous (server that ports 1-20 need to get to)
24 as promiscuous (WAN router where ports 1-20 need to get to and the remote servers).
[Code]...
I am interested in learning and setting up VPN IPSec with Cisco ASA 5505. I've managed to successfully setup VPN andcan connect to it from outside and browse securely to the outside/internet via tunnel. However, once I am connected to VPN, I cannot access any of my internal hosts/servers via VPN client. I am wondering it its a missing ACL/NAT...ASA Version 8.2(5)
!
hostname ciscoasa
enable password xxxxxxxxxxx encrypted
passwd xxxxxxxxx encrypted
names
[code]....
I am having an issue bypassing a switch 3750G series. How i can bypass the old configuration in the switch.i have tried the CTRL+BREAK at startup but it wont work.
View 2 Replies View RelatedI am going to change a running 6500 switch. I am missing a best pratice doc for changing a cisco switch configuration. My question is if a startup-config has an error (due to typo mistake, or due to comands not supported on latest IOS) and I do copy tftp startup-config then what will happen ? I want to make sure when I do "reload" the switch then it should boot normally with the latest startup config !
View 3 Replies View RelatedI'm in the process of upgrading my 4507R core to a new 4507R-E. The old switch has Sup IV engines (WS-X4515) running IOS 12.2(40)SG and the new switch has Sup 6L-E engines running 15.1(2)SG. I'm trying to "move" my configuration from the old switch to the new. Below shows the commands configured in the old switch. I'm trying to determine how to implement the same configuration on the new switch since these commands are no longer available.
View 2 Replies View Relatedrecently we purchased cisco smart care, and today i recived this notification: Configuration RegisterCriticalNot fixed on switch it is set to: Configuration register is 0x2101
what is recomended conf reg for this switch?
I have a 2960 that bounced several times over the weekend and then appears to have lost its configuration. Using CDP from the backbone switch pulls up the information below. Is there any way for me to configure the downed switch from another switch on the network? I am trying to avoid having someone from the site try to find a console cable and a suitable computer with a serial port. [code]
View 2 Replies View Relatedwhen enabling multicasting on layer 3 interfaces the CPU becomes fully utilized , is there any specific configuration should be enabled to reduce this .
Config :
Inetface vlan 100
ip pim sparse-dense
ip igmp version 3
[Code]......
I did the DHCP configuration for my CISCO 2960 switch but the clients are still not able to get the IPs.see the configuration below.
(config)#ip dhcp database cisco.com
(config)#pool test
(config-if)#client client-id vlan 500
(config-if)#ip dhcp snooping trust
I am uploading new configurations to my Cisco 3750 stacked switch and noticed that after the load I cannot log back into the switch because my password somehow was changed. After performing password recovery and getting back into the swtch, I noticed the configuration register was 0xF. I have never seen this before. The config-register command does not seem to be supported to change it back to factory default. The switch is on a ship which has several power hits when they switch power from shore to ship power.Can this cause the configuration register to change? What is the best way to change the configuration register?
View 1 Replies View RelatedI have stack of 2 switches 3750?I config etherchannel between them.
here is result
2 Po2(SD) LACP Fa1/0/15(I) Fa2/0/15(I)
Both ports are up up but standalone Int port channel 2 is down down.Need to know if this is default behaviour when we config etherchannel between stack switches?
