I have 6 of these WS-CBS3012-IBM modules that need to be configured but I cannot access the USB console port. I was told I could just get any DB9- to- USB cable and that would work. I did buy a DB9-to-USB cable and it did not work. I looked up the installation guide for this module and it just said the console cable is DB9-to-USB but with no part number.
View 3 RepliesIm having problems changing a connection between a Cisco3560 and Cisco IBM Blade switch 3012 actually the configuration is access in Cisco 3560 and trunk int Cisco 3012 when i change the connection to trunk i lose conecctivity to the servers connected in the 3012, i have changed the access from vlan 1 to the respective vlan in the access port of the servers
View 5 Replies View RelatedI planed to configure a new catalyst 2960 switch with console cable.
During the boot, all seems ok. but from my terminal client, I can't have access to configuration mode.Keyboard or Terminal client is not sending commands to the switch.
The terminal is blocked on this line Compiled Tue 28-Sep-10 13:44 by prod_rel_team.what can I do to get access to the switch? [code]
Recently I have faced following problem in my office, We have purchased two new Dell Server Power Edge R910 with built-in 10GB FC Network card. Service tag of this two servers are given bellow.
1. 7D94C2S
2. 6D94C2S
You can can Check specification of this two server from dell website{ URL}
We have two CISCO switch and model is given bellow:
Brand: CISCO
Model: WS-C3560E-12SD
We want to connect server to switch through FC cable and both switch have SPF module. But when we connect server to switch, link do not establish even switch and server port light become off.
Then we have tested the following things:
1. Connect server to server through FC cable, it is okay.
2. Connect switch to switch through same FC cable, it is okay.
I don't understand why it is not working.
I have vm with 2 nic card and 2 blade switch 3120g in the same hp c7000 blade enclosure. How to setup etherchannel as highlight in attachment ?
View 4 Replies View Related i have one of my switch modules that shows PwrDown when i issue the command show mod.
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 9 Supervisor Engine 32 8GE (Active) WS-SUP32-GE-3B SAD09120263
2 48 48 port 10/100/1000mb EtherModule WS-X6148-GE-TX SAL1029VWZ5
[Code]....
i tried disabling the diagnostic monitor for the module, did a power enable module command and then reset it but it still fails. this is the third blade that i am replacing in a few weeks and i still get the same error. i am persuded that it is not a hardware since it is the third blade in a matter of weeks. after the module reset, i receive this error % module 3 is operationally off (FRU-power failed)
could an ios upgrade solve this issue? are there any ios related bugs?
I received 3 GESM cisco blade switches for a HP Blade system. I do not have the chassis. I need to sanitize these blade switches but I have never worked with these. I don't see any removable flash. Where is the config stored?
View 7 Replies View RelatedWe are facing issue with one of the module installed on cico 4506 swicth. All of a sudden cisco phones connected to that module went down and the messages logged on the console. [code]
View 9 Replies View RelatedI try to connect a cisco blade switch 3020 to Nexus 2232 with etherchannel, but when I connect the second link a obtain flapping on vlans. [code] why the vlans are flapping ? it's something wrong on the config ? [code]
View 7 Replies View Relatedshow logging
May 1 16:00:30: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to down
May 1 16:00:39: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to up
May 1 16:17:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to down
May 1 16:17:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to up
May 1 16:25:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to down
May 1 16:25:37: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to up
May 1 17:19:25: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to down
Configuration as below:
macro name vmware
switchport trunk encapsulation dot1q
switchport mode trunk
no switchport access vlan
[code].....
Note:Both active blade switch and standby one are connecting to same aggregate switch 3750. Yet the active one, with same config as standby one, has not occurred this issue.
Where can I find a sample working configuration of (HP rebadged) 3120 Blade Switch?
I have the Cisco 6500 end configured as follows:
interface Port-channel1
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,300,304,310,320,560-562,600,740,770,950
switchport mode trunk
load-interval 30
[code]....
I will be connecting 9/5 and 9/6 to Cisco 3120G (HP rebadged) Blade Switch in c-Class Enclosure tomorrow.It would be nice to have a rough sample configuration of the above 3120G switch.
Any recommendations for top of rack switch for within our data centre.Dual power is a requirement, but bandwidth and through put will not be huge as such I have been looking atthe WS-C3560X-48T-L and the Nexus 3048.
View 1 Replies View RelatedI purchased an old cisco 831 for practical studies for a cisco certification. I purchased the console cable (serial/rj45) and a usb->serial converter cable. However when I open my terminal application (tera term) After I select the right com port (3) and make sure the connection settings are right. It will just sit idle and not show any data from the device. Was I sold a faulty device? It lights up and has three lights on.
Everytime I look at a manual or cisco video I am given the impression the terminal application will just automatically connect. But whenever I try I get nothing.
I cannot connect to the Cisco 2801 with console cable. what to do ?
View 1 Replies View RelatedI have a client whom has asked me to enable web management on some of his 2960 switches. I did not think this was going to be an issue, and so I told the customer I would set this up for him.
Much to my dismay, I have been able to get http and https enabled, and then authenticating locally for the HTTP access. I then come to the screen once authenticated which is shown below:
The issue is that when I select "Web Console", it gives me a "Web Page Cannot be found".
I can't connect to the console of switch cisco sge2010, I tried several console cables and none worked for me, I followed step by step manuals and nothing.
Also try the web 192.168.1.254 according to the manual but when I connect from the laptop to do ping to the switch doesnt work.
So I have read about proper procedure involving the connection between a console cable and Hyper-terminal. I have also tried plugging into a network port to obtain an IP Address but nothing seems to work. When powering on the switch I see that it lights up, hear fans spin and assume it has booted properly. I'm using Hyperterminal on Windows Xp Pro SP3 and I've also tried minicom in Fedora.
And just FYI Hyperterminal was set to the proper:
Bits per second: 38400
Data bits: 8
Parity: None
Stop Bits: 1
Flow Control: None
My requirement is that I want to set same console password in 12 switch instantly...
All the 12 switch are connected to a cisco 6500 L3 switch..
So how can i do that.. i have cisco acs 4.1...
can i do that by cisco acs 4.1 if not tell me an software or command ...
I have 2960 switch and i can't access it using my console cable .I can access other switches in my network ( 3560 & 2960 ) but i can't access only this switch.may be the console port in the switch damaged? or it's a bug ?? !!! although the switch is worked normally.
View 11 Replies View RelatedI am not getting interface up/down logs in my switch console through show logging command. Switch model cisco WS-C4506-E and IOS :- cat4500e-ipbasek9-mz.122-53.SG3.bin. I have done below mention configurations, we can't configure logging level beyond informational. [code]
View 4 Replies View RelatedI have 2 Catalyst 2924 switch in a home lab. Both of them have developed the same problem at the same time (strange). I have tried all that I can think of. I can telnet to them but cannot access via the console port. On a telnet session I execueted a "write erase, reload" on one of them. As I anticipated this threw me out of the telnet session and I presently have no access to that switch.
The console cable is fine, works for all other devices.
I want to configure my switch via console cable, the switch boots up normally, and there are no configurations present on the switch. However, anything I type does not appear on the terminal client. I used several terminal clients (TeraTerm, PuTTY, HyperTerminal), all latest versions as well as different PCs. I even forced the switch to rommon mode, still, anything I type does not appear on the terminal client.
Here's the output of TeraTerm:
Boot Sector Filesystem (bs) installed, fsid: 2
Base ethernet MAC Address: e8:40:40:06:f0:80
Xmodem file system is available.
The password-recovery mechanism is enabled.
Initializing Flash...
[code]....
After the last line, I can not type any command at all. I encountered this on three 2960 switches that we have here in our laboratory.
I've been assinged a task to connect our branch office with the head office, so that the IP Phones in the branch office can be connected to Cisco Call Manager at head office. To accomplish this they have given a Cisco 877 Adsl router a 10 Port 3-COM POE Switch and 3 Cisco 7911 IP Phones. Currently the there are 7 PC's Connected to 3 COM Switch which indeed is connected to a Internet router(Speedtouch). First I thought of connectiong the IP Phones to the Ethernet Port on Cisco 877 router but had to change my mind as the ports are non POE ports and I do not have adapters for IP phones. So I've decided to connect the Phones to 3 COM Switch and create VLAN's (DATA & VOICE) and pass the DATA traffic through Speed Touch and Voice traffic through the Cisco 877 router, but when I tried accessing the 3-COM Switch via Console I am getting Junk language( See the attachment for reference).
how can I pass through this Junk messeges and access the switch
[Code].....
i'm trying to enable command authorization for ssh as well as console access to a Nexus 7010 box (version 5.0). Following is the config:
aaa group server tacacs+ ACS5-1
server 10.12.19.11
server 10.12.19.12
source-interface loopback0
snmp-server enable traps aaa server-state-change
aaa authentication login default group ACS5-1 local
[code]....
As you can see, the default group configuration ACS5-1 for authenticatoin has applied to both defaults and console. But the command authorization does not appear to be applied to the console. As a result, when i login from the console and get authenticated, the command authorization does not trigger and i can run commands I'm not supposed to. In the configuration, I do not see "aaa authorization console" option unlike we have in IOS.
is it possible, to use a Catalyst Switch (in my case a 3560E) as a source for a console session to another Catalyst? In principle to use it as a console terminal server.
View 1 Replies View Relatedcan we connect ASA 5550 to Nexus 7K F2 module using twinax cable?
View 4 Replies View RelatedSuffered a big outage on the network, the fix was to reload the module 3 on the 6509 switch, we had these errors on the log %CONST_DIAG-SW1_SP-3-HM_PORT_TEST_FAIL: Switch 1 Module 3 TestUnusedPortLoopback Port(s)[24,46] failed. System operation continues.in the end, we reloaded the card and it was all ok. is there anything I can do to check the card / or any deeper logs? would that error cause the card to crash?
View 1 Replies View RelatedAny doc for installing the a PoE switch module for a 2951? I find alot about the 2951 PoE Power supply but nothing for the switch module.
View 5 Replies View RelatedWe have Communication Media Module (WS-SVC-CMM) mounted on 6513 switch. It went down twice and we brought it up by applying "power enable module".
View 4 Replies View RelatedI'm trying to set up a 2951 with a 24 port switch module. I want the ports to act similiarly to the ports on an 881 router - where I assign the VLANs on the router and I set the VLANs to the switchport interfaces.I would like to be able to create the VLANs on the router portion of the 2951 and then, enter the switch module and configure the Ports to the VLANs but, how do I logically connect router to the switch? Is it an internal logical interface - meaning how are the VLANs getting from the router to the switch?
View 24 Replies View RelatedWe have supplied Cisco Swtch 2960 with gig SFP modules. It is working fine. However, when I do a show inventory it show proper part no. for the switch chassis but for the GLC T module it shows as unspecified in the PID column.
View 1 Replies View Related I have a problem with a newly bought ws-x4548-rj45v+ i've plugged in the module but when i do show modules all , it show as unsupport
Power consumed by backplane : 0 Watts
Mod Ports Card Type Model Serial No.---+-----+--------------------------------------+------------------+-----------1 2 Supervisor IV 1000BaseX (GBIC) WS-X4515 JAE1048GAXQ2 48 10/100/1000BaseT (RJ45) WS-X4448-GB-RJ45 JAB064806WN3 48 10/100/1000BaseT (RJ45) WS-X4448-GB-RJ45 JAB063005DB4 0 Unsupported module WS-X4548-RJ45V+ JAE1545056U
M MAC addresses Hw Fw Sw Status--+--------------------------------+---+------------+----------------+---------1 0007.0e64.f880 to 0007.0e64.f881 5.2 12.2(20r)EW1 12.2(46)SG Ok2 000b.5fa4.da20 to 000b.5fa4.da4f 1.0 Ok3 0009.e844.d760 to 0009.e844.d78f 1.0 Ok4 ccef.4815.9bf0 to ccef.4815.9c1f 2.0 Unsupport
My questions is can a 4 port PoE switch module (EHWIC-4ESG-P) and a 8 port switch module (EHWIC-D-8ESG) be used at the same time in a Cisco 1941 router?
View 1 Replies View Related