Cisco Switching/Routing :: Linksys SRW2048 - Connection Between Console Cable And Hyper-terminal
Feb 16, 2012
So I have read about proper procedure involving the connection between a console cable and Hyper-terminal. I have also tried plugging into a network port to obtain an IP Address but nothing seems to work. When powering on the switch I see that it lights up, hear fans spin and assume it has booted properly. I'm using Hyperterminal on Windows Xp Pro SP3 and I've also tried minicom in Fedora.
And just FYI Hyperterminal was set to the proper:
Bits per second: 38400
Data bits: 8
Parity: None
Stop Bits: 1
Flow Control: None
View 1 Replies
ADVERTISEMENT
Feb 24, 2013
I have lost the original console cable to the Cisco Linksys SRW2048 and was wondering if I can use the Cisco console cable or can a regular serial cable with female ends will work?
View 2 Replies
View Related
Jan 2, 2013
I have a problem with my switch. The model no. of the switch is as follows:
Linksys SRW2048 10/100/1000 48 Ports
Serial No: RJT00GC00395 GGR2906 MM
1. I am creating a home computer lab. I do have 3 servers HP ProLiant DL 385 G1. Two of them have 6 gigabit ports where as the third server has 2 gigabit ports.
2. Installed ESXi 5.1 on two servers where as installed FreeNAS on the third server and configured it as iSCSI storage and NFS storage.
Problem:
1. Every port works perfectly fine. However, when I keep connecting the ports of the switch to the ports of servers, internet gets disconnected.
2. Interestingly, my wireless internet also gets disconnected, the ports of the switch does not have any internet now.
3. This happens till I connect above 8-9 ports of the switch to the servers.
3. However, when I remove the connection between the switch and the servers, internet comes, wireless internet starts working; and the port of the switch also gets internet connection when I check the internet connection of the individual ports one at a time.
Some more information:i do have internet service provided by Time Warner Cable. My internet speed is as follows:
Download Speed: Up to 15 Mbps
Upload Speed: Up to 1 Mbps
I do have a modem *** router by Motorola which has 4 gigabit ports.Model no: Motorola SURFboard SBG6580 i am assuming it is some thing related to bandwidth of the internet.
View 4 Replies
View Related
Oct 23, 2012
I have a set-up with multiple C2960 and C3750 switches. All these devices are being managed remotely. So basically I login to C2901, which is used as a Terminal Server, and reverse SSH to the console of each device. That's - I have assigned an IP to each port of the terminal server so that I can SSH directly to the desired device through via the mapped IP.
Now, recently I had to restart couple of switches - one C2960 and C3750. I initiated the reboot via console connection remotely. I could see the device logs for some time and then the logs stopped and there was no reaction from the console irrespective of any command I tried to enter.
I tried resetting the line on the terminal server, but that didn't work.
Now when I try to SSH the IP mapped to console of that particular device - i dont get any login prompt and there is no effect on device after giving any command. Although i can see the logs on the console session - but cant do anything.
I have a second way of connecting the device via inband- management, and checked the device config found it correct. It is same as other devices which are working correctly.
Both C3750 and C2960 are behaving exactly same - can see logs on console but see effect of even pressing enter - not getting login prompt as well.
View 4 Replies
View Related
Nov 11, 2012
is it possible, to use a Catalyst Switch (in my case a 3560E) as a source for a console session to another Catalyst? In principle to use it as a console terminal server.
View 1 Replies
View Related
Jan 3, 2013
I have cisco 2911 router, this router not load putty and hyper terminal. my last command is confreg 0x3242 from rommon mode.
View 1 Replies
View Related
May 5, 2013
I have a Cisco ASA 5505. This has been previously configured. I am trying to give it a factory reset and I am being able to connect via Putty and Hyper-terminal but I cannot enter anything. I am able to go into ROMMAN mode by using the esc key.
View 6 Replies
View Related
Oct 23, 2012
I want to connect two linksys SRW2048 through fiber optic.. it's located different rooms with fiber optic....Is it possible through VALN....This setup using for CCTV connectivity?
View 1 Replies
View Related
May 30, 2012
I purchased an old cisco 831 for practical studies for a cisco certification. I purchased the console cable (serial/rj45) and a usb->serial converter cable. However when I open my terminal application (tera term) After I select the right com port (3) and make sure the connection settings are right. It will just sit idle and not show any data from the device. Was I sold a faulty device? It lights up and has three lights on.
Everytime I look at a manual or cisco video I am given the impression the terminal application will just automatically connect. But whenever I try I get nothing.
View 2 Replies
View Related
Jun 12, 2013
I cannot connect to the Cisco 2801 with console cable. what to do ?
View 1 Replies
View Related
Dec 12, 2012
I planed to configure a new catalyst 2960 switch with console cable.
During the boot, all seems ok. but from my terminal client, I can't have access to configuration mode.Keyboard or Terminal client is not sending commands to the switch.
The terminal is blocked on this line Compiled Tue 28-Sep-10 13:44 by prod_rel_team.what can I do to get access to the switch? [code]
View 3 Replies
View Related
Jul 27, 2011
I have 6 of these WS-CBS3012-IBM modules that need to be configured but I cannot access the USB console port. I was told I could just get any DB9- to- USB cable and that would work. I did buy a DB9-to-USB cable and it did not work. I looked up the installation guide for this module and it just said the console cable is DB9-to-USB but with no part number.
View 3 Replies
View Related
Jun 11, 2013
I have two 3560s that i would like to upgrade. But first i would like to make -absolutely- sure i dont wind up in a situation where i have to roll back over a console connection.to the day i still cant understand why oh why someone removed (or chose not to implement it everywhere) tftpdnld from rommon ;)
View 8 Replies
View Related
Aug 13, 2012
Everytime the console port is plugged in, the alarm contacts (1-4) randomly assert (trigger) and then clear themselves in random orders. Nothing is plugged into the ALARM port and all Alarm setting are default. Below is the syslog message and Alarm Settings:
CGS2520-C#show env allSYSTEM TEMPERATURE is OKSystem Temperature Value: 45 Degree CelsiusPOWER SUPPLY 1A TEMPERATURE is OKPOWER SUPPLY 1B TEMPERATURE is DisabledPOWER SUPPLY 1A Temperature Value: 49 Degree
[Code]......
View 3 Replies
View Related
May 10, 2012
I have 2691 router with following config
line console 0
login local
password xty
When i remove the login local from the line console i connect to console port and press enter it shows router prompt 2691Router> but i am unable to go to enable mode.If i telnet to router then i put username and pw then it goes straight to enable mode.
vty config is
line vty 0 4
exec-timeout 600 0
logging synchronous
login local
length 500
transport input telnet ssh
escape-character 3
Any reasons why i can not go to enable mode by console?
View 3 Replies
View Related
May 14, 2012
I have a Win 2003 server set up as my DHCP server. It is connected to port 13 of my SRW2048 switch.
Every port from 1-12 and from 25-36 get a "Limited or No Connectivity" error when I plug an ethernet cable in them from a computer (Win XP). However, all of the other ports receive an IP address and connect to our network just fine. I've noticed that they are all in the two right hand banks of ports,though, so I'm in need of assistance as to how I can get the first two banks of ports to behave the same way. In other words, I want all of the ports on the switch to be able to populate an IP address from the DHCP server attached to port 13.
View 8 Replies
View Related
Apr 26, 2011
What kind of cable is required to connect to the Console on a Linksys SRW2024 switch ? ( I've lost the original cable )I use the following settings: Speed 38400, 8 bits, no parity, no flow control and stop bits 1I have tried a serial cable, no go.I have tried a null modem cable with partial handshaking, no go.I have tried a null modem cable with full handshaking, no go.For the null modem cables, if I use it to connect between computers using hyperterminal it works very well. What I type on one computer appears on the other computer's screen.However, I can't get anything out of the switch. I've tried pressing Enter repeatedly, resetting the switch with the Console cable on, etc.
View 2 Replies
View Related
Nov 18, 2012
I am runing 802.1x and MAB authentication of devices connected to a 3560 switch (in test). When I run 'terminal monitor' I am getting alot of authentication fail-msg. Is it possible to get the switch not to show them? I have to do some debugging on SNMP and DHCP to be able to figure out why I get these msg, but since the switch is blasting out so many auth-msg it is hard to see the debug messages. [code]
View 3 Replies
View Related
Apr 22, 2012
I have a switch(6500) with 2 vlans(2 SUBNETS) and from the other side of my network i have 2 terminal servers.
I want to have a VIP in my 6500 switch which i have the 2 vlans and when the first vlan(network) try to connect to the VIP
my switch will forward to first terminal.When the second vlan try to connect to VIP the switch will forward to second terminal.
I'd like the switch to decide in wich terminal server will forwared the packet based on source network.
I am not sure how i can do this???I use VIP with SLB???I use NAT???PBR?
View 4 Replies
View Related
Feb 28, 2012
I have 100+ 3750's that are running various IOS, some stacked and some not, and all seem to have the same problem.If I attempt to paste a configuration into the terminal session I get booted after about 10 to 15 lines. This happens when using SSH and Telnet. Telnet will go a little further before I'm booted. After I'm booted it sometimes takes a minute before I can log back into the switch. Any issues pasting configs into a 3750 via a VTY session?
View 4 Replies
View Related
Oct 29, 2011
I'm trying to set up VLANs in my network.So the first device after the internet cloud is my ISP modem/router. I don't really use the router part. The second device is my Linksys WRT54G router with DD-WRT firmware on it.Between the two, there is a subnet just for them. After the DD-WRT router, there is a subnet for my LAN.The third device is my netgear GS108T switch (with vlan support) to which almost all my computers are hooked up. One of those computers is my server that is domain controller and has the roles as shown in the image. What I would like to do is to create several virtual machines in Hyper-V. The trick is that I want to isolate them from the rest of my network. They should be able to access (and be accessed) from the internet but not the rest of my network. So my whole network should be in the same VLAN but each VM should be individually in separate VLANs.
1) I've allready created the VLANs on my Netgear Switch. I know my DD-WRT also has VLAN support. Do I need to create the same VLANs on that also?
2) How to configure the VLAN part of the Hyper-V server? (by the way, my server OS is Windows Server 2008 R2 with the hyper-v role, it's not the bare-metal hyper-v)Should my Virtual Switch be in VLAN 10 and my VMs in the other VLANs?Should the port (on the netgear switch) in which my server is connected, be in VLAN 10 (so that my server is accessible from every other computer in the network)?
View 6 Replies
View Related
Aug 9, 2012
I have a 6513 with redundant sup 720-3B's that I cannot get onto. In short, one of the power supplies failed, it still passes traffic but I can't console or ssh to the box. Other than the two sup 720's, I have a 4 port 10gig card, a 16 port GBIC Card and an IDS module. I have tried removing the 10Gig, IDS and one of the sup's but still don't get anything on the console. I have rebooted the entire chassis and don't get anything on my console while booting. I have tried changing the speed of my terminal to every setting available incase someone has changed it at some stage but to no avail. I have tried swapping sup's, using only one at a time in the chassis but not getting anything. Is there anything else I can try to get onto this chassis? The power supply is a 3000w with a 32amp input. The failed power supply had tripped a switch, when i brought it back up, the power supply came out but the output failed LED is on. My #questions are, is there anything else I can do to try get onto the console, and is the power supply goosed when the RED LED is lit? I have reseated the power supply also but the same result.
View 2 Replies
View Related
Jan 4, 2012
i have 2811 router and i am coneccted via concole so i want to copy the 2811 ios to my PC is that possible?
how or give my the right decument to do this.
* idon't want to use TFTP becuse i have no ethernet connection to the router(only concole)
View 5 Replies
View Related
May 19, 2013
I have installed a cisco 2911 router and the cisco usb console drivers on my pc, win 7 64 bit.however when I use putty and open the com port assigned it just goes blank, I am using the usb port on my laptop to connect and using the cisco usb console cable provided
View 1 Replies
View Related
Apr 3, 2012
I have a 3560-24ps, and I'm having issues with it booting. When I power the device up all the front panel lights come on like normail, and then the system light starts flashing like normal, but after 5 - 6 seconds the system light goes off. I don't get any output from the console, and the fans still run.
View 5 Replies
View Related
Dec 16, 2012
Is there a way to turn off 802.1x authentication messages to the console of a 3750 switch? The issue we have is that we like to monitor the terminal when remotely configuring our switches. However, every time a computer authenticates to the network we get messages and sometimes quite a few depending on the situation.
View 3 Replies
View Related
May 3, 2013
I attached the terminal to the console port to watch the bootup sequense, but nothing appear the same cable used on athor switches and router without any issue.procedure to access the router noting that Giga ports not working also.
View 2 Replies
View Related
Nov 13, 2011
I have a client whom has asked me to enable web management on some of his 2960 switches. I did not think this was going to be an issue, and so I told the customer I would set this up for him.
Much to my dismay, I have been able to get http and https enabled, and then authenticating locally for the HTTP access. I then come to the screen once authenticated which is shown below:
The issue is that when I select "Web Console", it gives me a "Web Page Cannot be found".
View 11 Replies
View Related
Sep 27, 2012
I have 2 3750-x members in a stack running 12.2(58)SE2. I am able to console into the stack master, which happens to be the top switch, but not able to console into the 2nd member. I get the screen stating the console is available but never get the prompt to login. Is this expected behavior?On our stacks of 3750v2's, I'm able to console to any switch in the stack?
View 1 Replies
View Related
Mar 18, 2013
I can't connect to the console of switch cisco sge2010, I tried several console cables and none worked for me, I followed step by step manuals and nothing.
Also try the web 192.168.1.254 according to the manual but when I connect from the laptop to do ping to the switch doesnt work.
View 3 Replies
View Related
Feb 29, 2012
today I received a Cisco 1841 Router with a problem i have never seen before. Maybe this my 1st really,really broken Cisco Router. When I power the Router on, the fan and all lights turn on (green) and that's it. Nothing changes, also after minutes of wating. On console i don't get any messages and I already tried every BAUD rate possible. Switched the router off/on again and again. And no, it's obviously not a console problem of my computer, because i tried with different routers.
View 3 Replies
View Related
Sep 10, 2012
I have stack of 2960 S switches.I can console only from Master not from memember switches is this default behaviour?
View 1 Replies
View Related
Nov 3, 2011
My requirement is that I want to set same console password in 12 switch instantly...
All the 12 switch are connected to a cisco 6500 L3 switch..
So how can i do that.. i have cisco acs 4.1...
can i do that by cisco acs 4.1 if not tell me an software or command ...
View 3 Replies
View Related
