Cisco Switching/Routing :: Catalyst 4507R+E With WS-X4748 Blade - Ports Not Working
Mar 28, 2011
I have a Cisco Catalyst 4507R+E (with Sup7-E) and two blades; one WS-X4748-RJ45V+E and one WS-X4648-RJ45-E.
When I connect a device to a port on the WS-X4748-RJ45V+E blade the port will not come up, show interface shows the status as "notconnect". When I connect the same device to the WS-X4648-RJ45-E blade the interface comes up.
The WS-X4748-RJ45V+E blade seems to have initialised okay, it appears in the output of "show module" as OK.
I get exactly the same effect on a second, identically configured Catalyst 4507R+E.
The software version is IOS XE 3.1.0SG, which according to the release notes supports the WS-X4748-RJ45V+E blade
If i replace a card of the same type in the same slot will I lose the configuration for that card or does it live in the backplane of the device?Is there any special command I need to run to replace the card or can i shutdown the 4507r-e and just swap out the blade?
We have 12 Catalyst Blade Switches 3020 for HP running IOS Version 12.2(55)SE. In the configuration of these switches I see the statement shown below.
no spanning-tree vlan 34,45-55,70,600,643,840,843-850
The 12 blade switches are configured as VTP clients and running VTP V2. I did not configure the statement shown above. It appered by itself. And even if I delete it, it will reapper. (The blade switches are interconnected to two 6509s. The two 6509s are the STP root and VTP bridges. I configure Vlans and STP on the 6509s).
why the statement above appers on the blade switches 3020s?
I mean I use other Cisco switches such as 3750s and 3560s and I have never seen the statement above appear by itself.
This log message is produced Catalyst4507R+E.The device is inserted SUP-7 with 3.1.0SG Image.With this log message, the device produced duplication packet of multicast. Dec 2 16:40:00.276: (Suppressed 269 times)Dup Packet Fail for Sw Port
My Company use Core Sw 4507R-Sup 7L-E with Enterprise Services License. I has upgraded to use iOS cat4500e-universal.SPA.03.03.01.SG.151-1.SG1.bin
When I use match protocol in class-map, there are only about 10 protocols, and not have those ones I need. I intend to expand the list of protocols to do some Policy-map by loading PDLM. But 4507 is no longer support NBAR. So do we have another way to set Catalyst 4507R with Sup 7L-E recongnize more protocols in match protocol command?
We're having kind of a problem with our Catalyst 4507r switches. If we do a "show interface" command we're getting a lot of "Total output drops" on some of our interfaces. It seems to be most of the time on the same vlan.I was wondering if it has got something to do with QOS or queue selection As we don't have any QOS markings configured, is it possible that all traffic is using only one of the four tx queue's?
I will be connecting 9/5 and 9/6 to Cisco 3120G (HP rebadged) Blade Switch in c-Class Enclosure tomorrow.It would be nice to have a rough sample configuration of the above 3120G switch.
Are all ports on Catalyst 4500X Gigabit/10-Gigabit or just the ports on 8-port module. We are looking at 4500X for campus distribution layer but need Gig ports to access switches for now and may year from now will be using 10G.
I work at a hospital and we have 3750X-48P switches in stacks in various locations throughout the hospital. We have noticed that when an EKG machine is plugged into one of the ports on some of these switches and the EKG machines are set manually to 100/Full, the ports are no longer usable until the switch is restarted. The switch is configured for auto. If the EKG machine is set to auto, it will work and not cause problems. The link on the interface will show up/up and there will be output packets increasing. However, there will be no inputs on the link and the port is unusable. Unfortunately, even when the device is removed, the port becomes unusable for any device. Is there any way to fix this problem without rebooting the switch?
in my production environment two swtiches with stack and all ports are in the same Vlan 2 192.168.117.254 and the default getway is 192.168.117.1install correctely all were working fine but from yesterday onwards some of the ports are getting down automatically and coming up automatically and all devices are having static IP's no dynamic. [code]
I have a Cisco Catalyst 2960 series switch. When I connect another switch or a VMWare Esx server on one of the ports, the port blinks for few seconds and then goes off. When I connect a desktop or laptop or a windows server the ports stay led and I can access resources on the network. However, when connect another switch or a vmware esx server, the port is disabled.
What config in the switch can I check to make sure the ports stay on regardless when I connect a desktop / laptop, switch or vmware server?
We've got a doubt about the uplink ports of this supervisor. I've read that you have to use the four ports in 10G mode or in 1G mode, but not use for example 1 port in 10G mode and 1 port in 1G mode:
But, you can read in another sentence: " Beginning with Cisco IOS Release 12.2(25)SG, you could simultaneously deploy the dual 10-Gigabit.Ethernet ports and the four Gigabit Ethernet SFP ports on the Catalyst 4503, Catalyst 4506, and Catalyst 4507R chassis." Is it posible deploy simultaneously both type of ports?
I have a cisco 6509 switch in which i have 2 SUPs. I am using 3 Qty. of WS-X6748-GE-TX in the same switch. First 24 ports of module 1 and are not working. I replace the faulty moldule with the working one but now the new (good) module's first 12 ports stopped working. But when I insert the good card (the replaced one with the faulty) in other chassis it works fine.
This has been happening repeatedly time to time! we just replace the part! But now it has come to trouble us again.It happening only in one module like 6 to 10 ports wont work.
we run IOS cat4500e-universalk9.SPA.03.02.00.SG.150-2.SG.bin will there be any bug in it?
Unable to limit traffic on catalyst 3750 gigabit ports it has fiber modules,
I want to limit traffic 2mb per port
I have tried srr-queue and policier but it is not working and there is no ratelimit command under any interface, Applying policy to output is not supported of the interface
policy-map rate-limit class class-default police 2000000 8000 exceed-action drop int gi1/0/3 service-policy input rate-limit
I am trying to test the gigabit ports on a Cisco 2950 switch. 1000Base-SX. I have the internet or dhcp server connected to port 24 on the first switch and my pc hooked up to the (any) port on the second switch. Both switchs are connected with a fiberoptic cable with MTRJ connectors on either side.
Now when I use gi0/2 on both switchs all works fine. I get a dhcp address from the router on the other end of the first switch. but when ever I include gi0/1 on either end of the fiber optic cable neither of the ports will initialize (neither of the leds above the ports light up). I have deleted all the config files before booting up the switchs so they should have a default blank configuration.
When looking at the Http web page for the switch I dont see any issues with the port. what can I do to make sure these ports are working or can be configured?
I will not be able to post back any more information about the switch until next tuesday. Im off till then.
I have two switches, WS-3750-24PS-S connected in two cabs via fiber. Patch panels at both ends with patch leads. Used tester to confirm end to end fiber connectivity. When plugged in, one switch lights up the other does nothing.
same at both ends. Tried both GI ports same result. swapped transceivers over and the same result, (one switch lit one not - the same switch in both cases). put both transceiver in each switch, (gi0/1-0/2 in a single switch). on the one that lights up in the original scenario we get link on both ports and they come up, on the other nothing happens. shut down both ports on the malfunctioning switch and no shut them, no change.
Show transceivers doesn't show transceivers on the malfunctioning switch, and no attempt is made to bring the ports up if the fiber is removed and replaced.
it is almost as though the two gb ports are kaput. Anything else I can try?
Multicast is not working between our two datacenter, we have catalyst 2960S (two stacked) as the internal lan switch, and catalyst 3560E as the external switch, same configuration for both datacenters.The two sites are connected using metro, the external switch (3560) is doing qinq and encapsulate the data from the internal switch with the metro vlan (611).
IGMP snooping is disabled for all switches, although we prefer to enable it for the internal switches.For each datacenter there is a different firewall which also act as the router, we are using fortigate as the firewall.Following is the important configuration section:
Port 43 in the internal switch is connected to the external switch (both sites):
I've created some port forwards from my public IP (Dialer0) to our private LAN but only the 25565 port forward works. I've even added an any statement to the Nat source list Homenet_NAT. Full config attached. My Cisco router is an 877W. [Code]
Im having problems changing a connection between a Cisco3560 and Cisco IBM Blade switch 3012 actually the configuration is access in Cisco 3560 and trunk int Cisco 3012 when i change the connection to trunk i lose conecctivity to the servers connected in the 3012, i have changed the access from vlan 1 to the respective vlan in the access port of the servers
Looking at the specs for WS-X6704-10GE, it shows the port buffers at 16M per port. This doesn't seem like very much for a 10G port. Is this upgradable or related to how much RAM is in the blade?
we have 2 WS-X6516-GE-TX, WS-X6516A-GBIC, and a WS-X6748-GE-TX with a WS-F6700-CFC daughtercard
our sup is a WS-SUP720-3B
we are experiencing packet loss for everything connected in the WS-X6748-GE-TX blade, right now we dont have any production device in that blade due to the packet loss we are experiencing.
this switch was running hybrid before it is now running native ios, however I can't recall if we didn't have that packet loss before. do i need to update a firmware of the card or daughtercard (if this is possible, can't say i've done it before).
i have one of my switch modules that shows PwrDown when i issue the command show mod.
Mod Ports Card Type Model Serial No. --- ----- -------------------------------------- ------------------ ----------- 1 9 Supervisor Engine 32 8GE (Active) WS-SUP32-GE-3B SAD09120263 2 48 48 port 10/100/1000mb EtherModule WS-X6148-GE-TX SAL1029VWZ5
[Code]....
i tried disabling the diagnostic monitor for the module, did a power enable module command and then reset it but it still fails. this is the third blade that i am replacing in a few weeks and i still get the same error. i am persuded that it is not a hardware since it is the third blade in a matter of weeks. after the module reset, i receive this error % module 3 is operationally off (FRU-power failed)
could an ios upgrade solve this issue? are there any ios related bugs?
I have a LAP-1142 connected to one of our PoE blade in our 4506 switch, it used to work fine with the following power consumption:
Interface Admin Oper Power(Watts) Device Class From PS To Device --------- ------ ---------- ---------- ---------- ------------------- ----- Gi4/3 auto on 21.5 20.0 AIR-AP1252AG-A-K9 3
However, we had power issue on Apr 28, so it failed and we saw from the log below:
Apr 28 13:57:38.990: %C4K_ETHPORTMAN-3-INLINEPOWEROVERDRAWN: Inline powered device connected on port Gi4/3 exceeded its hardware protection threshold.Apr 28 13:57:39.694: %PM-4-ERR_DISABLE: inline-power error detected on Gi4/3, putting Gi4/3 in err-disable state After the power restored later, the other LAP connecting with the same blade restored without any problem, except this one:
Interface Admin Oper Power(Watts) Device Class From PS To Device --------- ------ ---------- ---------- ---------- ------------------- ----- Gi4/3 auto on 16.6 15.4 Ieee PD 3
- Incoming frames on three of a blade's four switchports are being put into VLAN 1 even though the ports are either in other access VLANs, or are configured as trunks with different VLAN IDs being tagged by the server. - When the ports go down the access VLAN is removed from the port.
Switch stack: 4x WS-CBS3120X-S, 12.2(58)SE1 HP blade: HP BL460c Gen8
This combination has been used successfully elsewhere.
Switchport configuration:
! interface GigabitEthernet1/0/13 -------> THIS PORT IS OK switchport mode trunk
I'm trying to get the VFC up in B22-FEX blade in Dell which is connecting to Nexus 5596UP.
The message I get is
# sh int vfc1033 vfc1033 is down (Error Disabled - VLAN L2 down on Eth interface) Bound interface is port-channel3 Hardware is Ethernet Port WWN is 24:08:00:2a:6a:0d:db:3f Admin port mode is F, trunk mode is on
I received 3 GESM cisco blade switches for a HP Blade system. I do not have the chassis. I need to sanitize these blade switches but I have never worked with these. I don't see any removable flash. Where is the config stored?
We have 694 units Cisco Catalyst 4507R plus E swithes accross the network. LMS 4.1 can discover it no problem however, i cannot extract inventory information for these switches. I get the this "Number of devices that do not have inventory collected data" on the report.installed System image file is "bootflash:cat4500e-entservicesk9-mz.150-2.SG1.bin"
i saw this supported version:
150-1.XO (or) 03.01.00.SG <<--- should i have the exact image or higher version will do? [Inventory Config and Image Management]
Reference: [URL]
Is the image installed on my switches not supported? seems like I have higher version.
I try to connect a cisco blade switch 3020 to Nexus 2232 with etherchannel, but when I connect the second link a obtain flapping on vlans. [code] why the vlans are flapping ? it's something wrong on the config ? [code]
I have 6 of these WS-CBS3012-IBM modules that need to be configured but I cannot access the USB console port. I was told I could just get any DB9- to- USB cable and that would work. I did buy a DB9-to-USB cable and it did not work. I looked up the installation guide for this module and it just said the console cable is DB9-to-USB but with no part number.
I'm having issues getting the ports g3/5 and g4/5 from inactive to notconnect.
I have tried the hw-module uplink select all in the global configuratio, but it's not working, getting a : % Invalid input detected at '^' marker. Message every time.
This what I have:
Power consumed by backplane : 40 Watts Mod Ports Card Type Model Serial No. ---+-----+--------------------------------------+------------------+----------- 1 48 10/100/1000BaseT (RJ45) WS-X4548-GB-RJ45 JAE152101QK
