Cisco Switching/Routing :: Traffic Policy Is Not Working On Catalyst 3750?
Jan 28, 2013
Unable to limit traffic on catalyst 3750 gigabit ports it has fiber modules,
I want to limit traffic 2mb per port
I have tried srr-queue and policier but it is not working and there is no ratelimit command under any interface, Applying policy to output is not supported of the interface
policy-map rate-limit
class class-default
police 2000000 8000 exceed-action drop
int gi1/0/3
service-policy input rate-limit
still when I start download it goes to 10 mbps
View 12 Replies
ADVERTISEMENT
Mar 2, 2012
We are using Cisco 3750 switches in our environment as distribution switches.We currently use to police inbound traffic, but we need to find a solution to limit inbound traffic per IP.Something like this “Inbound traffic for each IP can be maximum 1 Mbps” This can be done having, one ACL and one class-map for each IP, but in my situation is not a practical solution, because we have more than 500 IP’s on that site.
Is any way to accomplish this without writing 500 ACLs and 500 class-map?
View 2 Replies
View Related
Jan 27, 2013
I have catalyst 3750 I want to controle traffics on every port I have tried Frame-Relay Traffice shaping and Quality of service but there is no support for these commands in the switch.do we have any way to limit traffic on every port in catalyst 3750 and 2960 switches ?
View 4 Replies
View Related
May 4, 2011
is there a way to assigen a QoS service policy via Radius to an Caltalyst 4500/3750 Switchport?
in detail, we would like to assign this policy
policy-map SET_EF class class-default set dscp ef
to an interface. All traffic should be marked with a defined DSCP value.
This works find when doing it statically with
interface FastEthernet2/1 service-policy input SET_EF
but we would need to assign such a policy via Radius during the 802.1x Authentication. different users should get differnt policies. We use Cisco ACS 5.2 as Radius Server and there actually is a field for that in the Authorization Profile Common Tasks Configuration. in detail, this uses the cisco-av-pair "sub-policy-In=<policy name>" attribute to assign a service policy to an NAS.
we found also two other attributes "sub-qos-policy-in" and "ip:sub-qos-polcy-in" for that. CCO says that "ip:sub-qos-polcy-in" works with Catalyst 65k [URL]
unfortunately this seems to not work on Catalyst 45k and 37k.
In the ACS Logs we can see that these attributes are attached to the Radius Reply, but unfortunately they are ignored by the switch.
it is interesing that when entering "show aaa attributes" on the Catalyst 45k, these attributes are displayd - so for my understanding the switch should understand these attibutes (?)
4503-E#sh aaa attributes AAA ATTRIBUTE LIST: Type=1 Name=disc-cause-ext Format=Enum Type=2 Name=Acct-Status-Type Format=Enum
[Code]......
View 1 Replies
View Related
Jun 10, 2010
I try to enter the command "ip policy route-map" on 3750's interface. But the command doesn't appear. Why? Whereas I see several times that this command is possible on this switch. What I have to do to enter this command?
View 3 Replies
View Related
Oct 17, 2011
I have a simple design with 3750. I configured a route-map which define a next hop. I defined this route-map on a policy on a vlan interface.When I test some ping and a debug ip policy and it seems that my policy never match.Is there any mechanism that prevent the switch from using PBR? I think of CEF .
View 5 Replies
View Related
Jan 28, 2013
In our datacenter we have a 3750 stack with IP base image. I have enabled PBR and reloaded the switch. Show sdm prefer says i am using default template. The reason i want to use PBR is that we have 2 firewalls on the same work and want to be able to have granular control over which gateway out of the network they use but still be able to access all internal resouces accross wan and locally.
Created access list to identify traffic:
access-list 10 permit 10.2.3.59 (test workstation on vlan 3)
Created policy:
route-map TestASA permit 10
match ip address 10
set ip next-hop 10.2.0.3
Assigned policy to the user vlan3:
ip policy route-map TestASA
Results:It changed the default gateway to the above gateway but i could not access any resources on any other vlan, could not access resouces accross wan.
View 16 Replies
View Related
Sep 5, 2012
I have a simple design with 3750.I configured a route-map which define a next hop.I defined this route-map on a policy on a vlan interface.When I test some ping and a debug ip policy and it seems that my policy never match.Is there any mechanism that prevent the switch from using PBR?
View 10 Replies
View Related
Dec 2, 2012
I have 2 ISP connected to Router A and Router B.Both the routers are connected to the core 3750 switch.. I want to send the traffic from the switch that goes to router A to router B..[code]
View 10 Replies
View Related
May 29, 2012
We have a Catalyst 6509 switch, and we hope to use policy based routing to redirect http traffic to my proxy server, where I can find the configuration example?
View 11 Replies
View Related
Feb 18, 2012
I am trying to do policy on the interfaces of my switch WS-4507R, below the configuration I used to shap the traffic to 1 Mbps. However, when I tested it the traffic excceded the 1 Mbps.
class-map match-all 1MB
match access-group name 1MB
!
policy-map 1MB
class 1MB
[code]...
how I can restrict my bandwidth on the interface on 1 Mbps.
View 2 Replies
View Related
Apr 23, 2013
I have a client with a 3750x stack. We've upgraded it to IP Services. We have a simple PBR setup. One access-list to forward traffic from a specific LAN ip to another gateway on the network.
I go to vlan1 (default vlan) to apply the PBR and the command takes with no errors, but do a "show run" and it doesn't show up under the interface.
I go to vlan1 and apply a PBR that doesn't exist and the command takes with no errors, and is listed under the interface in the config
I can apply the PBR globally and appears to work, but we can't have it there based on other issues it creates.
config: (all tracks are up)
C3750_stack#show sdm prefer
The current template is "desktop routing" template.
[Code]....
View 8 Replies
View Related
Nov 1, 2012
I am trying to configure policy based routing however when i try to apply to an interface vlan. The configuration does not show in the interface.
route-map OTHER_ROUTE permit 10
match ip address OTHER_ROUTE
set ip next-hop x.x.x.x
[Code]....
View 4 Replies
View Related
Dec 24, 2012
i would like to know the possibility to use mls qos trust dscp with service-policy in the IOS ver.12.2(25)SEE2.The specific version is not possible to configure like below.
Cat3750(config-if)#do sh run int f1/0/1
Building configuration...
[code]....
View 8 Replies
View Related
Jan 26, 2009
I have a 3750 switch (c3750-ipbasek9-mz.122-46.SE.bin) were i want to add bandwitdh limit pr. interface, doing the following:
ip access-list extended customer_A
permit ip any any
class-map match-all BW_10Mbps
[Code]....
When i trie to apply the "service-policy output 10 Mbps" to the interface, it says the service-policy output is not supported on the switch. Is this a software related isue ?
View 4 Replies
View Related
Apr 22, 2012
Here is my configuration below , i have upgraded my C-3750 switch IOS from IPbase to IPservices , after upgrading i have tried to apply PBR on my Vlan 4 and failed , when i am tying to apply route-map to Vlan4 the command was taking but i am unable to see the route-map when sh run , i am giving the command as "ip policy route-map TTSL" in my Vlan4 , below is the configuration.
In Vlan2 i have connected one ISP and Vlan4 I have connected one ISP , my local subnets are 192.168.1.x and 192.168.2.x , now i want to route the 192.168.1.x traffic from Vlan2 and 192.168.2.x Traffic from Vlan4 .
sh boot
coreswitch#sh boot
BOOT path-list : flash:c3750-ipservices-mz.122-35.SE5/c3750-ipservices-mz.122-35.SE5.bin
[Code].....
View 9 Replies
View Related
Sep 27, 2012
We have a metro Ethernet service, basically our WAN connection, that we use to connect 4 sites. This MOE service has a CIR of 200 Mbps, connected to a port on a 3550-12T running Version 12.1(22)EA5 at 1000 Mbps. We are exceeding our CIR at times during the day for short bursts which is causing the MOE switch to drop packets, which I suspect I am seeing manifest itself in some choppy VoIP conversations and dropped ICMP packets from our network monitoring software. I implemented policy maps to apply an outbound service policy to the interface connected to the MOE service, but I am not seeing any matches to the access lists or the service policy. I’m not sure if I am missing something or perhaps the IOS is not capable?
Below is the config for the service policy and some command output. Notice that there are hits on a statndard access list that is used for other purposes, but the extended access lists used for the class maps have no matches.
!
class-map match-all REALTIME
match access-group name REALTIME
[Code].....
View 4 Replies
View Related
Jul 25, 2012
have 3 Catalyst 3750 in same stack, the IOS version is 12.2(53)SE2. Today we can not telnet/ssh to this switch, but ping is ok, and switch function is ok. I try to access the console port, it show "low on memory, try again later". After I reboot the master switch in the stack, the master switch change to another switch, then I can telnet/ssh to this switch. I check the Ciscoworks server syslog report, there are many MAC address flapping error message, and I beleive the MAC address flapping occured before several weeks. ( the G2/0/15 & G3/0/15 is connect to a VMware ESX server and the EtherChannel config mismatch with this Catalyst 3750 switch ) How to mention the root cause of the "low on memory" problem and what is the abnormal memory usage ( free memory percentage below ?% )?
View 5 Replies
View Related
Apr 9, 2013
my Catalyst 3750 switch. Following a power cut the switch no longer boots up. The SYST light flashed green but no POST checks are made. I cannot see any boot messages from the console port either. The switch was on a UPS but some thing may have damaged the switch.
View 7 Replies
View Related
May 13, 2012
There is a requirement to configure tacacs and radius on catalyst 3750X (version 15.0) where two vrf exist.Is therer a solution to configure "tacacs-server,host x.x.x.x vrf yyy" ?? I know it is possible to configure under the "aaa group server radius xxx" the command "ip vrf forwarding yyy".Is there anything else for the tacacs-server and radius-server command?
View 2 Replies
View Related
Feb 18, 2012
Is is correct that vlan's exceeding 128 runs without spanning-tree.?
View 7 Replies
View Related
May 2, 2012
I have Catalyst 3750. and 2 ISPs
I wanted to use, let say on port5 of Catalyst 3750 only 2nd the ISP will route to this port.
The rest is pointed to the 1st ISP.
Im thinking of using VLAN..
View 7 Replies
View Related
Oct 24, 2012
I have a network with a Catalyst 3750 as the main switch and then some Catalyst 2960 switches that are plugged in to that. I have a server running windows server 2008 with a couple of virtual machines running in Hyper-V. I created 4 VLANS listed below and gave the 3750 the following IP Address.I would like the 3750 to only be configurable from VLAN 40 but currently every VLAN can connect to it, I noticed in the standard web page settings there was a setting for "Management VLAN" but it was set to 1 and would not let me change it, I kinda assumed that was for the management port in the back.-Now the tricky part, I was trying to set up routing between the VLANs and so far I have only been able to get a sort of "all or nothing" routing to work. I can turn IP routing on and add two or more VLANs to the routing and it works fine. But what I was hoping to do is create a couple of "junction vlans" that would only route to one or two other vlans. For instance, I wanted to create a VLAN 100 that routed to VLAN 20 and 30 but nothing else. I also want to route VLAN 1 just to VLAN 30, and so on. I am able to do each one of the cases but only one, it seems like the switch only supports one "routing table" am I missing something or is this just a limitation of the switch?
View 2 Replies
View Related
Oct 28, 2012
I have a network with several catalyst 2960 switches and one catalyst 3750. I have created two VLAN and set up the proper routing and everything is working fine there. I have a client/server application that used multicast in the initial start up for the client to determine available servers, the issue is one of my clients is on a different VLAN then the server. I am able to route the multicast using MVR as long as both the server and the client are plugged into the 3750 by creating a static route, making the server a source port and the client a receive port. Unfortunately I need the client and the server plugged in to different 2960s. My question is how do I establish multicast routing between the two and perferably do it dynamically (always route multicast traffic from one VLAN to another).
View 2 Replies
View Related
Dec 17, 2011
I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net.
My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20
I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2)my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to go out to the internet. I think it has to do with the routes. [code]
View 4 Replies
View Related
Apr 16, 2012
I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net. My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20,I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2),my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to,go out to the internet.
View 3 Replies
View Related
Nov 10, 2011
I have some trouble with that policy-map on my 2960 or 3560 switches with LAN base 12.2(53)SE2. I want to use that feature to catch video traffic from webcams in laptops which can't send dscp values out of the box. This is my test config to check if the function is working: catch every traffic from my workstation for testing, access-list 101 permit ip any any, class-map match-all CL_TEST
1. I can't see any counters with the command "sh policy-map interface FastEthernet 0/1". Cisco tells that this command is not possible. But how I can see if the policy is working correct?
2. When I did the configuration I can't see any packets with dscp af41 on the out going interface on the switch with "sh mls qos int gi0/1 statistic" as I expected. After reloading the switch I see the pakets with af41. Okay for that moment. But.After that I changed something in the policy-map. Only "set ip dscp ef" for a second test.
Generating some traffic I see only packets with af41 as before I changed the policy-map. No traffic with ef on the outgoing interface.
View 4 Replies
View Related
Jan 6, 2013
interface Vlan24
description Internal Wireless Internet
ip address 10.x.0.1 255.255.254.0
[Code]....
So, I am trying to limit the bandwidth used by this vlan. The service-policy output statement works, the service-policy input statement does not. My test is to get on that vlan and go to speedtest.net. My download speeds are about 3.5Mb/s, my upload speeds are about 20Mb/s.
it has something to do with this:
sh mls qos ip
QoS Summary [IPv4]: (* - shared aggregates, Mod - switch module Sid - Switch Id)
Int Sid Mod Dir Class-map DSCP Agg Trust Fl AgForward-By AgPoliced-By
[Code].....
View 1 Replies
View Related
Oct 11, 2012
I was browsing the Software Adviser on Cisco's website to look for a suitable IOS image, for a 3750. The system displayed a couple of suggested IOSes. there was no mention of IOS 15.0SE version.Could the Software Advisor be not up to date with the current Catalyst IOS releases?
View 1 Replies
View Related
Dec 31, 2011
I have CISCO catalyst with VLANs (VLAN ID 33, 36, 40-53) configured. I need to configure port mirroring in Switch 3750 for NAC (Network Access Control). I need to Monitor all the VLANs. Here is the SPAN configuration of switch: [code] Monitor session 1 source vlan 33 , 36 , 40 – 53.Monitor Session 1 destination interface fa 1/0/8 (here I am not able to set encapsulation dot1q ) because the error occurred saying %one or more dest port do not support the encapsulation%.
View 5 Replies
View Related
May 28, 2013
I have customer who has as Core Switch one Cisco Catalyst 3750 with the IOS c3750-ipbase-mz.122-35.SE5.I know that this image support DHCP Server configuration, but I like to implementate new vlans (approx 15) and I want to know if this switch support 15 DHCP Servers.
View 3 Replies
View Related
May 27, 2013
How to setup a port channel between a SG200 and 3750 and am having problems.
What do I need to do on the SG200 I have added the port into the lag but the port will not come up.
I spent half a day messing arround with the web interface and I am unable to get the port to come up.
The Cisco 3750 is a standard port channel config which I have setup maytime before. channel-group 1 mode active channel- protocl lacp Switchport mode trunk
View 1 Replies
View Related
Oct 13, 2012
I am working in an environment where i have to use more etherchannels, any way that how many etherchannels could we create on Cisco Switch 3750 e. do they can utilize high process resources of CPU.
View 4 Replies
View Related
