Cisco WAN :: 2921 Router - Configuration Required As NAT / PAT Gateway
Jan 14, 2013
I have a Cisco 2921 Router,with 3 giga interfacesi have a leased line for the internet with a public ip address and i want to configure this router as NAT /PAT gateway, so that users in my network can ue the internet by the router,my wan interface is g0/0 - ip 122.xx.xx.xx lan is g 0/1 -- 192.168.1.1 /24 . i have tried doing nat once but i was not able to make the wan port up.using cisco CP when i test the interface it givves error and i dont get internet to my users.
I was slightly dissapointed with the performance of the "pre-sales" phone number of Cisco in the Netherlands so I am asking it here instead.We decided on using 2 Cisco 2921 routers with 2.5GB ram to use for a MultiHomed connection using BGP. We already have our v4 and v6 space assigned as well as our AS number. The connections should turn up soon.What I could not find out with proper certainty on the Cisco Feature Navigator is if the IP BASE on the Cisco 2921 supports both IPv4 and IPv6 routing combined with BGP. This model uses the Universal IOS licensing which I found slightly confusing. I could not find a simple matrix with the supported commands either.
I'm configuring a 2921 Router. It has 3 GigE ports, of which I'm using 2. I would like the router to also act as a Gateway system between the 2 networks. Can you tell me which configuration commands I need to accomplish this?
I followed:[URL]And my VPN connection is established on 2921.However when I successfully connected to the router via VPN, ipfoncfig shows default gateway being 255.0.0.0,My CISCO2921 GI0/0 has default 10.10.10.1 IP assigned, I want to access this interface with CISCO CP.
We recently purchased a Cisco 2921 router to be our edge device for a small satellite office (24 users). In addition, to the router we purchased a vwic3-2mft-t1/e1 module. Now the surprise, we ordered a bonded T1, I thought we were getting frame-relay circuits from Verizon, but someone ordered a 3M IMA circuit. I am new to configuring serial connections, and had planned out a frame-relay configuration. With that said, I have the following questions:
1. Can I setup a working serial connection to Verizon using the installed ATM circuit and the 2921 and vwic3-2mft-t1/e1 card I have? If not, what do I need in conjunction with the 2921?
2. With the frame-relay configuration, I enable controllers, configured the MFR interface and sub-interface, and serials. How much different is setting up serial ATM connections?
I am having a public IP address and it is not configured on any of the router interface on my Cisco router. I am having 3 internal networks. Is there any way to PAT all these 3 internal networks to this public IP?
i have a router 2921 with the aproprieted voice card for E1 and licenses. I would like to know how to configure it for incoming and outgoing calls. I already configured the ephone and SIP phones for internal calls. now i just need to configure it for send and receive external calls.
Router: IOS: c2900-universalk9-mz.SPA.153-1.T CME: 9.1 ISP from Brazil: type: E1 signal: R2 Digital Channels: 32 Phone Number Iniital: XXXX-9250 (main) ephones-dn numbers: 9250 to 9280
I have configured my two vdsl link with ppp multilink but i am not getting the desired bandwidth. Here is my configuration is this okay or i need something more in the configuration. My router is 2921 what is the maximum WAN throughput of 2921? [code]
I am very confused on how I setup a Pix 515 that I just got to route traffic out a cable modem. First, let me give you a little details on my current network setup and what I am trying to accomplish with this Pix 515. Currently all my users go out the proxy for any internet access, however I have certain users that need to go out the cable modem instead of the proxy server. Below is an example of the current IP setup of a user A:The cable modem that we currently have has DHCP so I would need the external PIX address to accept a DHCP address. I also don't really understand what else I need to setup so if I have say four users hitting the cable modem through the pix how do I direct their web traffic to the correct computer (NAT ?),I will be plugging the PIX into a cisco switch that all ports are in VLAN 48 so hopefully a static internal address on the pix of 10.24.48.254 will keep me from having to do any routes since all traffic will be originating from the 10.24.48.0 network.
We have purchased a new Websense 10000 Appliance and I'm not a hundred percent how to set this up. I see that URL Filtering is a possibility and WCCP, which way to move forward on implementing this?
I am trying to set up my Cisco 520 router with a firewall that will: Allow port 80 traffic to the vlan 20,Block all other incomming ports to vlan 20 (unless initalised from inside),Allow all outgoing ports on vlan 20,Block all access from vlan 20 to vlan 10 (unless initalised from vlan 10)
I have a problem with the configuration of the ACL of my ASA 5505 router.However, the syntax seems okay,access-list 121 extended deny icmp 192.168.0.0 255.255.255.0 .
How can I have access to the cisco "AP#" prompt? When I try to acees the AP through hyperterminal, it gives me the attached messages. The message keeps looping and not letting me access the AP# command prompt to assign an IP address so that I can control it in mode HTTP.
I have existing Sonic FW in my company we are moving from sonic FW to ASA 5510 Security plus lice. I have two ISP currently connected to sonic Firewall I am planning to implement Dual ISP configuration on ASA5510.
I have a /25 block of public ips from my ISP which I'd like to subnet into two /26 blocks. I have a Cisco 2600 with 2 ethernet ports in it. What are the commands I'd need to take my 200.180.200.0 255.255.255.128, gateway 200.180.200.1 and turn it into 200.180.200.0 255.255.255.192, gateway 200.180.200.1 and 200.180.200.64 255.255.255.192, gateway 200.180.200.65? One of the interfaces will be connected to the ISP & the other to a switch, and then we could access the two subnets through the switch.
(2) identical DSL connections, configured as Static IP (not PPPoE) with modems in bridged mode. Static IP's are /25 subnet and same gateway ** this may be a problem? Dual WAN set for Load Balance, network service detection is OFF
We have a 2003 terminal server running and successfully receiving connections through both WAN connections. Depending on location, half the users are connecting to WAN1 IP and the other half to WAN2 IP. We are getting sporadic disconnects of the remote users when they are idle for a couple minutes and automatic reconnection of the session takes over a minute. If they close the (locked up) session and reconnect manually it will let them in right away.
Could the handling of the Dual-WAN be the culprit? Could the same gateway for both WAN's create this issue upstream (out of my control)?I am going to move everyone to connecting through WAN1 and then change to Smart Link Backup and see if the issues persist.
Another thought is to use a secondary IP on the terminal server and use Protocol Binding to match "All traffic" for IP1 to WAN1 and IP2 to WAN2, which theoretically would stabilize the situation?
I want to start implementing a small outdoor mesh network of 3 APs Aironet 1550 in order to grow afterward with more APs. Is there any way to configure those 3 APs in an outdoor mesh configuration (for example, only one RAP and two MAPs) without a Wireless LAN Controller or I have to have at least, one WLC? My idea is to have a WLC 5508, but at the very beginning I don't know if my budget is gonna allow me to cost the WLC.
We have implemented VSS on Cisco 6504-E switches using the 10GE links on the Sup-720-10GE. Two Cisco WLC 5508 controllers are planned to be connected in a LAG configuration, (consisting of eight links per LAG bundle) to each of the 6504-E chassis( Total of four WLC, two for primary and two for secondary). WLC HA feature may be implemented on the primary and secondary WLC controllers using the 7.3 latest code release.
We have 2 sites with 2 internet connections at each site. All are SRP527w routers. 1 is for internet and 1 is for a site to site VPN as,Currently we are using Static Routes on the PC's so they can access each server no matter what site they are at. I have looked at using the Static Routes section on the SRP's but cannot get it to work.
I've gotten to the point where I can test against active directory and get in, also I can get AD groups from my server on the ASA. My problem, I can't connect in via my AnyConnect client on my Android. I immediately get a "log in failed" and I know I'm using the right username/pass. Doing a little troubleshooting, I have attached my AnyConnect debug log and the results of the "debug ldap 255" command on the ASA. Also, I've used ldp.exe to determine I can connect in with the username/password combo I'm using.Combing through the AnyConnect logs I see a few instances of "global error unexpected" but no Google searches have brought up anything useful.
I am just going to deploy some new 4900Ms for a customer. Want to know if configuring management for 4900 (everything like NTP, AAA, SNMP , DNS ) is doable through management interface in management VRF and there are no caveats to be aware of.
I have a cable broadband installed in my home i just bought cisco 1200 series access point...now how to configure my access point. I believe I have to plugged fastethernet cable coming out of my cable modem to access point after that? What I have to do ....do I have to configure the cable modem as wlel or not???
This is regarding CISCO logging configuration.We palnned to implement enable logging on all the cisco nexus switchs.we are running HP arc sight in our DC this device monitor all the CISCO devices.We want to enable logging with this Arc sight device.Just I would like to know about config commands for Nexus device, what is the command to enable logs which is include "who is login & logout?, interface down information?,who was did conf t ? & every logs"
I have one firewall need to be configured in transparent mode. I have inside and outside router. What is the configuration of transparent firewall ASA8.2. I didn't find the configuration on Cisco site.
I recently swapped out an RV082 with a newer model (still RV082 but black and a different interface). I configured the Gateway to Gateway VPN exactly as it was before but none of the three other RV082's will connect. I have tried deleting the connections several times to no avail. I have aggressive mode disabled and have tried with the firewall on and off. Below are the settings (IP's have been X'd out) and the log.
Settings: IP OnlyIP Address : X0X.X0X.20.31Local Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : Remote Group Setup Remote Security Gateway Type : IP OnlyIP AddressIP by DNS Resolved : Remote Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : AES-192AES-256AES-128 AES-192AES-256 AES-128 IPSec Setup3DES Keying Mode : ManualIKE with Preshared keyPhase 1 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 1 Encryption : DES Phase 1 Authentication : MD5SHA1Phase 1 SA Life Time : secondsPerfect Forward Secrecy : Phase 2 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 2 Encryption : NULLDES3DES Phase 2 Authentication : NULLMD5SHA1Phase 2 SA Life Time : secondsPreshared Key : Minimum Preshared Key Complexity : EnableLOG:
My two RV042 , one at home and the other one at my working site, constantly lost VPN connection after successfully connected.Both Firmware are identical. [code]
we do have 2 Rv042, one in my office and one in my house.. in the office we do have static ip and at home none.. question is can i connect the two RV042?
We have a VPN setup between two Cisco RV082 routers, the VPN status shows as connected however I can't ping the other network. I am unable to ping between routers, let alone ping computers behind those routers.
We have 2 branches, branch 1 is on a static IP and branch 2 is Dynamic. I am able to connect via QuickVPN from Branch 2 to Branch 1 and remote desktop to computers, however have yet to VPN/remote desktop in the opposite direction.
To me it seems like a firewall issue at branch 2, but what's causing this. Also they are currently running 2 differnet firmware version not sure if this would cause a problem.
