Cisco WAN :: Setting Up Vpdn On 2600 To Connect ISP?
Apr 17, 2011
I have configured VPDN/Dialer on router 2600 to connect to our ISP via Fibre Optics modem but its simply not connecting. The router consists of 3 interfaces
- Inter fa0/0 = 10.0.0.6 255.255.255.248 (LAN 1)
- Inter fa0/1 = IP is unassigned (interface connected to Fibre Optics modem)
- Inter e1/0 = 192.168.200.1 255.255.255.0 (LAN 2)
The connection is planned to run like this:
LAN1 & LAN2 (Inter fa0/0 & Inter e1/0) <-> Inter fa0/1 <-> Dialer1 <-> Modem <-> ISP <-> Internet.
The Modem will just server as mere "modem" or just a bridge, as the actual routing is configured on "dialer interface" in the router.We're not using a dedicated IP address to link to ISP but a public one. After configuring the interfaces, VPDN, dialer interface, NAT, access-list, ISP's assigned username/password, etc I'm simply not connecting to our ISP, even when I do a ping. The ISP's IP address which we're pinging is 118.23.8.80 What am I missign out? How do I connect the dots here?Below are the results for Running config, Ping, and Debug:
Running Config:
Router1#show running-config
Building configuration...
Current configuration : 3083 bytes
!
! Last configuration change at 17:39:43 Sun Apr 17 2011
!
version 12.3
[code]....
View 2 Replies
ADVERTISEMENT
Jan 19, 2013
I'm setting up a IPSec Tunnel between 3800 and 2600 routers over the internet.
Do I need to create a tunnel interface as they suggest in this document? [URL]
I just watched a couple of you tube videos saying I don't need to do that...
View 8 Replies
View Related
Mar 19, 2013
I've recently purchased a 2504 Wireless controller, and I have 10 2600 APs to deploy. I think I've set up the wireless controller OK - there doesn't seem to be much that needs to be done! But I just can't seem to register an AP onto the system.
Just to briefly outline what I have done, I have connected to the Wireless Controller via terminal emulator and run through the setup, then I have connected OK to the web interface, and I am able to view and amend the controller's configuration. So I have setup a WLAN and thats about it.
Next up I have powered on one of my 2600 APs, and I am able to view it working via terminal emulator again. But I am seeing it continually running the same routine to connect to a controller, and all the time it just fails. Below is what I am seeing.
One thing that I am unsure about is that I am unable to connect to the AP config pages via web browser, using the IP 192.168.0.97 (although it does ping okay). Is that odd?
And the main question - why doesn't the AP connect to the wireless controller? Do the APs need to be authroized on the controller first? If I check the controller's web interface, under Monitor - Statistics - AP Join, I can see the AP listed with Status "Not Joined" but I don't know what I need to do to make it join!
*Mar 1 02:28:54.579: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.*Mar 1 02:28:57.583: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.*Mar 1 02:28:57.651: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 192.168.0.97, mask 255.255.255.0, hostname APb0fa.eb56.5abf(code)
View 12 Replies
View Related
Jun 29, 2011
I have a Cisco 877 router at home, and I'm trying to configure it to act as a VPN server in order to be able to connect to my home network when I'm outside; I want it to work with standard Microsoft VPN client software (which supports PPTP and L2TP).
This is the output of the "show version" command:
Cisco IOS Software, C870 Software (C870-ADVIPSERVICESK9-M), Version 15.0(1)M, RELEASE SOFTWARE (fc2)Technical Support: [URL] Copyright (c) 1986-2009 by Cisco Systems, Inc.Compiled Wed 30-Sep-09 08:42 by prod_rel_team
ROM: System Bootstrap, Version 12.3(8r)YI6, RELEASE SOFTWARE
The router has quite a basic setup: a single username with privilege level 15, a single VLAN comprising all four Ethernet ports, an ADSL connection to my ISP, an internal IP address of 192.168.42.1/24, an external IP address assigned by my ISP, NAT enabled.
This is my current configuration (stripped of non-relevant or private information):
service password-encryption
aaa new-model
aaa authentication login default local aaa authorization console aaa authorization exec default local
aaa session-id common
[Code]...
View 1 Replies
View Related
Sep 15, 2011
I been working with PPTP server on cisco IOS since a log time ago. Up to release 15.0 seems is just stopped working. I mean external users can log in the pptp but after logged in there no traffic flow. A simple downgrade to 12.4 solves the problem.
But now i have all my infrastructure with ISR2 2901 and all IOS are 15.
View 5 Replies
View Related
Feb 11, 2012
We have a 3745 LNS router, currently there are less number of users connected.when a user dials request authenticated and one virtual-access interface is formed in LNS router.Now the user is disconnected the vpn and connected to VPN again in this case, whether the user is connected to the same virtual-access interface which was assigned before disconnecting or different virtual-access interface is created.
View 0 Replies
View Related
Mar 3, 2013
I need to use a Cisco ASA 5505 on a BT Openreach connection, The configs that I have ben using are below -
interface vlan2
nameif outside
security-level 0
[Code]....
View 1 Replies
View Related
Dec 25, 2012
I want to configurate Vpdn protocol PPOE but i can not write protocol ppoe under vpdn group name on cisco 2811. cisco 2811 iso is 12.4 T adventurer and i upgrade it 15.1 advansecure but problem is still.
View 5 Replies
View Related
Aug 16, 2011
I have VPDN running on our Cisco 1921 router running 15.2(1)T. Previously I was using Cisco 2801 router running 12.4(24)T4. I copied the config from the 2801 to the new 1921 router before replacing the router but now the VPDN isn't working.
Basically the users can connect and authenticate to the VPDN, but once they get the IP 192.168.12.10-20 IP, they can't access the internal servers (i.e. 192.168.12.120).
Is there any bug in the 15.2(1)T relating to VPDN?
Here's the VPDN section of the config:
vpdn-group TESTVPDN
! Default PPTP VPDN group
accept-dialin
[Code].....
View 5 Replies
View Related
May 17, 2012
our office has cisco 2600 series router. i want to know on how i can configure it to connect to another router in a different site.
View 9 Replies
View Related
Apr 28, 2013
- How can I connect an old 2600 router to a linksys WRT54G2. to access the internet. I think it is not possible
- What device do i need to be able to do it
View 5 Replies
View Related
Jul 23, 2012
I have a 2611XM that I am using as a terminal server for my lab setup. Async is using octal cables. It works great with routers of all different models, but when I connect a switch of any model, it does not work. The connectivity LEDs don't even light (they do for the routers). The switches in question are 3750s and 3560s.
I have tried straight through from the octal cable to the console port of the switch, as well as a rollover with a converter, no luck. This does seem to be independent of configuration on the console port - even before the console port of the routers were properly configured, I at least had indication of physical connectivity.
View 2 Replies
View Related
Jul 29, 2011
Just need to know where I can set a Max connect time so users dont camp on the ASA when they are not using it.
View 8 Replies
View Related
Feb 23, 2011
I am having wireless modem to connect the internet of BSNL, I Want to connect internet by wireless lan to another pc
proxy settings for connection
View 1 Replies
View Related
Jul 19, 2012
I recently bought a DIR-655 on amazon com, got a good deal. Since I'm old and slo, had issues setting it up, but finally got er dun!I set up a Network all by myself turned on player, did WPS(PBC) on player, and on D-Link. The router and Blu-ray are now friends, however, they are not on speaking terms.Network status on ol Blu- tries to connect then says - Network setting is completed, but cannot connect to the internet, Contact ISP.
View 8 Replies
View Related
Jan 7, 2013
Trying to set up E1200. I have a DSL connection, no Ethernet connection. I do have internet access. Cannot figure out how to connect.
View 2 Replies
View Related
Jan 18, 2013
set up my router. Trying to set up my 3G modem with TP-Link MR3020.
Tried troubleshooting to find out where it went wrong and just couldn't figure out. Just tried disabling the wireless security and *poof* I'm able to connect to the Internet. Right after setting up the Network Key, I can't connect to the Intertnet via my router.
Here are the datas.
Windows IP Configuration
Host Name . . . . . . . . . . . . : TOSHIBAM840
Primary Dns Suffix . . . . . . . :
[Code].....
View 5 Replies
View Related
May 8, 2011
I have been having some issues connecting my PC to my XBox360 using the wired approach, it seems to be massively temperamental to a point i decided to not connect the XBox via my router and instead put it straight into my spare network port on my PC. The basic jist of mynetwork confirguration is something like this: Internet cable > Virgin Media 256 Modem > Linksys BEFSR41 Router > PC. I had no issues with this setup, but as soon as i wanted to add my XBox into the mix, things got tricky. I plugged the network cable from my Xbox originally into one of the ports on my router and then went through the settings on both my Xbox and router. Again, i had absolutely no confidence in doing this myself since i don't mess with it, but after reading guides i finally got it sorted. Well, partly sorted. I was able to connect to my Xbox Live, however i was unable to connect to my Xbox to my PC (To stream files onto the Xbox). This was what i wanted to do, i didn't really want to use the Live anyway. So i went off to work again. In the end nothing was working, so i opted to connect my Xbox directly into my PC - So it was no longer connected through my router. I could SEE my PC on my Xbox, but i was unable to connect to it to stream anything. I then opted to disconnect my router (For no other reason than to rule it out) - Sure enough, the very second i disconnected the router, i was able to instantly connect to my PC and was streaming straight away. Once i was streaming, i was able to reconnect my router and that was that. But if i turned off my Xbox i would need to also turn off my router the next time i wanted to stream. How can i fix this so i don't have to continually turn off my router, is there a setting somewhere in the options on my router which can allow me to connect to my Xbox? Windows 7 Xbox 360 Linksys BEFSR41 - 2.00.02 Firmware
View 1 Replies
View Related
Jan 13, 2012
I have verified that I am set to auto connect however my wireless does not do so upon start. I have to do so manually each time I use my computer. This is a new problem since installing the newest driver update because I could not connect at all or randomly. The update fixed the connection problem and I no longer have dropped connections and wifi connection back to normal. HOWEVER it has left my auto connect nonfunctional.
View 7 Replies
View Related
Jun 30, 2011
I'm looking at purchasing one Cisco 2600 XM Series router that has IOS 12.4 on it. I put the IOS name into Cisco's feature navigator and it states that it supports SSH and IPv6. Can I buy that router, take the IOS off that one, and put it on another 2600 XM Series so I don't have to spend $400 on two routers with 12.4 on them?
View 3 Replies
View Related
Sep 30, 2011
I am trying to secure sub interfaces on a 2600 Router
interface FA0/1.1
No Access-group
Interface FA0/1.2
IP Access-group 110 out
Access-list 110 deny ip 2.2.2.0 0.0.0.255 1.1.1.0 0.0.0.255
Access-list 110 permit ip any any
This works but it blocks traffic both ways I only want to block one, I dont want FA0/1.2 to be able to access FA0/1.1 but I want all traffic to be allowed to go the other way
View 2 Replies
View Related
Jul 13, 2011
I have a cisco 877 router connected to our adsl broadband at our head office. I have managed to set this up with Nat and DHCP all working to let multiple users access the internet through our single static ip supplied by the ISP lets say the ip is 1.2.3.4.Our internal network is 192.168.1.0 255.255. 255. 0.I have a draytek vigor 2600 at a branch office set up the same with a static ip addresss supplied by the ISP lets say the ip is 5.6.7.8.The internal network is 192.168.4.0 255.255.255.0
I am trying to set up a VPN between the head office and branch office so the branch office users can connect to our internal server(lets say ip is 192.168.1.2) to receive group policies,access files and also telnet into our database server(lets say ip is 192.168.1.3).I have attached a sort of running config that i have pieced together from bits i have read on this site and others. I have tried these settings and other permutations of these settings but i cant seem to establish a tunnel even though when i show int tunnel0 on the router it says tunnel is up and line protocol is up, if i show ip route it shows that there is an ip address for the tunnel and that is about it(No vpn light on).
If it makes sense and that I have entered the right information? I have highlighted the parts i am not sure about in red(Quite a bit and obviously not the exact settings but what i think it should be). Once all the settings are correct on the cisco will it automatically establish the vpn or do i have to dial it from the draytek.
View 4 Replies
View Related
Mar 4, 2012
i want to configure the router for internet access for hosts this is the my pub ip x.x.x.174 and mask 255.255.255.252 this is isp given subnetmask internal ip range is x.x.x.20-x.x.x.254
View 1 Replies
View Related
Mar 14, 2013
I am new using cisco router 2600, i want to use dmz like adsl modem to direct ip public to ip lan like 180.15.22.x.x to ip lan 192.168.1.2 ( lrouter mikrotik ) outside to inside so when i call ip public then forrward to mikrotik
View 2 Replies
View Related
Aug 24, 2011
I was trying to erase my lab router 2600 and reset it back to the factory defaults. Well I was able to to reset it all right but I used the erase command which worked a little to well. So now there is no IOS and the router is in ROM mode and I didnt back up the pervious IOS "Nice". So was able to get an updated IOS for my 2600 but I'm trying to install it and don't know how. I was able to get a tftp server app for my windows pc but I'm unsure on how to configure it so I can transfer the new IOS to the router. On the up side I did learn something erasing and reset are to very different things.
View 6 Replies
View Related
Jun 20, 2012
I have 3 Cisco 2600 routers with the same IOS and memory.One of them has CME...
What would be the best way to copy the CME from the one router over on the other two?Backup my FLASH to my TFTP and then restore to the other two routers?
View 1 Replies
View Related
Sep 6, 2012
I ordered a set of hardware that came with CBT videos; however, the videos they sent do not exactly match the hardware and I'm stumped.
I have 3 routers:
2610XM: Indianapolis
2620:New_England
2610:Seattle
Indianapolis connects to New_England with a WIC-1DSU-T1
Indianapolis connects to Seattle with a WIC-1T
The interfaces are up on all three devices and so are the protocols. The videos are of 2500 series routers and they only use the WIC-1T card. When I try to set the clock rate for the s0/1 on New England to 1000000 like the video suggest I get an error "this command only applies to DCE interfaces". Do I not need to set this on the WIC-1DSU-T1 interface?
Whenever I issue router rip and try to set network such as:
router rip
network 10.0.1.0
network 10.0.10.0
network 10.0.20.0
the network won't save on any of the devices. If I show the running-config it shows network 10.0.0.0 I've tried saving the config directly after exiting outt of the config mode, but still only 10.0.0.0
View 4 Replies
View Related
Jun 10, 2013
I have a 2600 I am trying to setup for educational use.
My Cable ISP has issued me 5 routable IP's through their SMC modem 86.28.12.226-229. The SMC modem is .225. Currently the internal network can get out through .229 as expected but nothing outside (tcp 80 to web server) can get through. When I assigned the ip's to e0/1 as secondarr I could get it to route from the inside network (so hitting .226 80 went to the correct place) but it still didn't work from the outside - plus I read that wasn't a great way to do it anyway.
!
interface FastEthernet0/0
description LAN Interface
[Code].....
View 2 Replies
View Related
Jan 2, 2012
I nedd some Details for configuring the new internet connection from ISP.
I Will discribe the Curent network structre . We have a internet conection from one vendor That is comming to our router. we are using Cisco router 2600 that having two Ethernet ports.One port occupaid with connection from ISP ,One port going to ASA firewall.
We have a site site VPN conction with client between our ASA and thier ASA.
Now we need to configure one New internet Connection from another vendor .We need to use this new connection mainly for VPN.And once this connection is down we need to backup with old Connection.
how we will take the connection to the firewall or do we need to configure the new router.we have a new router.
View 6 Replies
View Related
Nov 10, 2011
- I have an older router 2600 running 12.1(4) IOS.
- There are a few clients connected to it via the frame relay connection.
- There is an IP that clients access 192.168.1.10 for example
- We need to do a NAT for this IP for one specific client only like "ip nat inside source static 192.168.1.10 1.1.1.1"
- However if I do that, that will effect other clients too
- On the interface for this client I'll be using "ip nat outside"
- Is there a way to accomplish this without effecting other customers?
View 6 Replies
View Related
Dec 29, 2012
How to know the serial 0 or 1 (to v35 modem)was good or not ? is there any tool (software) or hardwire jumper to simulate loop back ?
View 12 Replies
View Related
Apr 11, 2006
How to know the serial0 or 1 (to v35 modem)was good or not ? is there any tool (software) or hardwire jumper to simulate loop back ?
View 4 Replies
View Related
Sep 10, 2011
I have two LANs in my house, one 10/100 base and the other 10/100/1000, but one internet connection that I would like to have access to on both networks. Right now I have two Belkin routers for each network. In addition I have a Cisco 2600 and 3660. I know they are old, but they seem to be in operational order. Can I use those to combine to two networks? The only thing I want to maintain is the speed on the gig network, from the router to the PC's and devices.
View 6 Replies
View Related
