Cisco VPN :: Max Connect Time Setting ASA 5520?
Jul 29, 2011Just need to know where I can set a Max connect time so users dont camp on the ASA when they are not using it.
View 8 Replies
ADVERTISEMENT
Cisco Switches :: Setting SNTP Time For SG500?
Jan 13, 2013I had connected a computer and NTP to the SG500. i had successfullly sync the internet time on the computer. but when i type 'show clock' on the terminal. The switch did not manage to sync the ntp time.
clock timezone sg +8
clock source sntp
sntp unicast client enable
sntp server 192.168.4.36
Cisco Switching/Routing :: Setting C1841 To Sync Its Time With Another One
May 25, 2012i am setting a C1841 to sync its time with another C1841 over net. here is my setting with dont work !
SERVER:
clock set 23:01:00 26 MAY 2012
ntp master 5
ntp source f0/1
[Code].....
D-Link DAP-1522 :: Time Not Setting Correctly On DAP-1533?
Jan 19, 2013This appears to be a different issue than the one described in the sticky above. I have two DAP-1533's. Both are running firmware 1.02 from the Taiwan website. I am running both in Bridge mode at 5 GHz only. They both exhibit the same problem. If you go to "Maintanence > Time and enable NTP it never updates to the correct time. Also, after "saving" the time gets set to the same time as shown grayed out in the "Set the time manually" window. I am using this time server: ntp1.dlink.com and tried others and have tried time server ip address in case it was a DNS issue. Also, why is there no DAP-1533 section on the forum?
View 9 Replies View RelatedSetting Up A Time Capsule / Airport As Primary With E4200 Cascade
Mar 14, 2012I have a Time Capsule current generation, as my primary router connected to my ISP. I'm using a Linksys E4200 as my slave router connected to the Time Capsule via lan to lan. I noticed the TC Internet Connection TCP/IP via DHCP shows a Subnet Mask of 255.255.248.0 and the Surewest IP of 74.222.246.23
Is the 248 setting one I will need on the slave?
The TC IP Address is 10.0.1.1 the DHCP Beginning Address is 10.0.1.3 to allow for the slave to have 10.0.1.2.
The E4200 is set as follows on the routers setup page, Internet Section to Automatic DHCP, Network Section to IP 10.0.1.2 Subnet Mask 255.255.255.0 and DHCP is Disabled.
Both routers have a SSID set to the same name.
Are all these settings correct? I've noticed that a device iPhone or iPad etc has a different IP address assigned by the TC depending on which router it is actually connected. I've also noticed difficulty of a device on one router communicating with one on the other.
Linksys Wireless Router :: Setting Date And Time On WRT110?
Aug 28, 2008Setting date and time on WRT110
View 9 Replies View RelatedLinksys Wireless Router :: Setting Up MacBook Time Machine With EA4500
Jun 22, 2012How to set up a time machine MacBook Air (Mac OS X 10.7.4) on EA4500 (2.0.37) with the disk WD MyBook USB 2TbThe disk is divided into two sections 500 and 1500, 500 by the time machine.After the command (defaults write com.apple.systempreferences TMShowUnsupportedNetworkVolumes 1) time machine saw the network drives, but can not be backed up (not supported AFP)
View 8 Replies View RelatedCisco Wireless :: 4402 - Setting Update Time For Auto Tx Power Level Assignment
Dec 1, 2011We have a WLC 4402 controlling 40+ LWAPs. Is there a way to keep Tx power level assignment dynamic, but set the time of day it does it? I'd like to minimize user impact. (Firmware v. is 7.0.116.0)
View 2 Replies View RelatedCisco VPN :: Setting Up LAN To LAN Between ASA 5520 And Juniper Device
May 16, 2011i am setting up a LAN to LAN VPN between Cisco ASA 5520 and Juniper device. its my first time i am setting this up. What will be the peer device of my device that i need to give to the other person.. is this the outside address of my device ?
Also with the setup i have made i am getting the follwong error msg:
IKE Peer: 81.45.22.222 Type : L2L Role : responder Rekey : no State : MM_WAIT_MSG5
also i was getting Type: user intead of l2l - what does htis mean as well
Cisco Firewall :: Intrusion Prevention Gadgets Display Incorrect Time ASA 5520
Oct 3, 2011I have an ASA 5520 with the Intrusion Prevention Module.The time displayed on the ASA is correct.The time displayed in all Intrusion Prevention gadgets is ahead exactly 4 hours.Under configuration, Time the Time Zone is correct, Eastern in my case. The sensor local time on the same page is correct and is grayed out.I only work in the ASDM as I am far from being a CLI person.I don't think the time being off is causing any issues, but it is strange.
View 1 Replies View RelatedCisco Firewall :: ASA 5520 - Real-time Log Viewer Filter Not Showing Rule Hits With ACL
Dec 20, 2011I'm running into this issue on an ASA 5520 running version 8.2(2)9 and ASDM version 6.2(1).
I have an ACL denying traffic to a certain IP range and the logging level set to Debugging. The hit count is rising quite rapidly but when selecting "Show Log" the Real-Time Log Viewer opens with a value of 0x13d0ee2a in the "Filter By" field and no logs are ever shown.
Logging is enabled globally and Logging Filters on ASDM is set to Debugging as well.
how I can get the RTLV working?
Cisco Firewall :: ASA 5520 / Monitor Largest Outgoing And Incoming Traffic Per Ip In Real Time?
Mar 4, 2013We have a Cisco ASA 5520 and im looking for a way to monitor largest outgoing and incoming traffic per ip in real time so to know which of my internal computers are using the most of our Internet Line. Is there a way to this through ADSM ? We use version 6.3.
View 1 Replies View RelatedCisco Firewall :: ASA 5520 - Solar Winds Real Time Interface / Monitor Through Put Of Port?
Jul 6, 2012I have an ASA 5520 and I'm using Solar winds real time interface tool to monitor the through put of the port. It seems I can never get it to use more than 100mb, where should I check?
I have run a sh int giga 0/1 and it shows the port is 1000mb full duplex and the I have also checked the other end where it plugs into the LAN and this also says the port is running at 1000mb full duplex.
Cisco Firewall :: ASA 5520 - NTP Server For Firewall Clock Setting
May 22, 2013I have ASA 5520 installed. I want to use ntp server for firewall clock setting. I found one open-access ntp server (stratum 2) in Los Angeles:
[URL] 209.151.225.100
Can I use the following command to set ntp server?
ntp server 209.151.225.100 source outside.
Connect To Two Different AP At Same Time
Sep 21, 2011I have two wireless adapters "PCI Marvell Libertas" and "USB Sagem" and i have access to 2 different AP's, The browsing' seem to be a little slow while i'm downloading', and my work requires lot's of downloading', as i have managed to connect to my two different AP's at the same time, i always feel like i'm usin' only one of 'em, so i was wondering' if i can take advantage of both connection in order to double the speed, and or if there's some way to use one for browsing' and the other for torrent downloads only.i've tried to mount the USB adapter on Linux using' Vmware, but it keeps saying' unable to get IP address,,However that's not the problem,, all i want to know is if there's a way to make both connection work on windows 7 Ultimate X64,
View 1 Replies View RelatedCan't Connect 2 Laptops At Same Time
Jan 6, 2011I cant' connect my 2 laptops on the internet at the same time, only 1 laptop can connect on the net and the other one don't or they can both connect to the internet but it doesn't stop disconnecting on both of them.
View 10 Replies View RelatedHow To Connect 2 Broadband At Time
Oct 22, 2011How can i connect 2 broadband but 1 ISP provider at single switch hub
View 4 Replies View RelatedConnect To Two Routers At The Same Time?
Apr 20, 2011I have a wireless router in my house/office which allows everyone to print to a wireless printer and used to supply acces to the internet. Recently I purchased a 4G Internet card from Verizon (wireless connection for up to 5 devices) which works very well but when I am connected to it I cannot print to the wireless router. Is there any way to be able to connect to two routers at the same time?
View 11 Replies View RelatedCisco VPN :: RV042 Only One Computer Can Connect At A Time?
Jan 2, 2012Using RV042 router,have an office with 4 computers XP PRO SP3 and only 2 need to use the VPN connection.problem is each one will connect just fine BUT when one is connected the other will not connect untill the other is disconnected.have another office with very similar setup (same quickvpn client) (same router)and i have 2 computers connecting at same time just fine.have checked all i can think of.
View 2 Replies View RelatedCisco WAN :: 2621 / Time-Based Access Lists Using Time Ranges?
Jan 4, 2011I have one 2621 router i want to creat time base access list so that one of my subnet user(10.128.194.0 255.255.255.128) use only internet between 11am to 2pm.
View 15 Replies View RelatedCisco Wireless :: WAP321 Lost Time - Cannot Sync With Time Server
Jul 8, 2012I just bought a WAP321 Wireless AP. I wonder why it cannot sync with our time server automatically. Every time I reboot it, the system time become "Fri Dec 31 1999 12:00:00 UCT". I have to do the sync manually by clicking on the "Save" button under the menu Administration > Time Setting.
View 5 Replies View RelatedHow To Connect Two Wifi Network At Same Time
Dec 21, 2012i have two networks accessing through Wi-Fi..if u want to access resources of A network from B then what should i do...means i have installed SQL database server on A network & want to access on Network B
View 1 Replies View RelatedCisco VPN :: ASA5510 - Configuring Maximum Connect Time?
Jan 5, 2011I have configured the "Maximum Connect Time" as unlimited in my group policy but when a connection is established it shows a "Conn Time Out: 120 minutes". The connection does get dropped with this timer. how to actually make it unlimited and why it get sets to 120?I having a problem with SSL phone clients dropping throughout the day and think this may be the cause.
View 14 Replies View RelatedCisco VPN :: ASA 5510 - Maximum Connect Time Configuration?
Mar 21, 2011I have been working on my ASA 5510 version 8.2(1) trying to change the maximum connection time. Originally the custom "Group Policy" for IPSEC (Remote Access VPN) was set to inherit the settings from the default system Group Policy (DfltGrpPolicy). The custom group policy for the sake of this discussion is called "ABCD". I have modified the settings on the default (DfltGrpPolicy) as the custom policy (ABCD) was inheriting the configuration from default to disconnect after 1200 minutes. I changed the setting "maximum connection time" to 1200 minutes. I saved the configuration and what not then connected my VPN client, after two (2) hours I was disconnected. Something just doesn't add up.
I went ahead and deselected all inherited properties and manually configured them for the ABCD custom policy. No longer was the ABCD custom policy configured to use the inherited properties/settings. I saved the configuration again tested but instead of having a 1200 minute connection limit, I have 120 minute connection limit. Inside Monitoring --> VPN --> Sesssions : I can click on my session and see Session details". The Group Policy and Connection Profile properly list the "ABCD" custom profile. However, the "Conn Time Out" setting is: 120 minutes. I am completely stumped as to what is going on.
In the actual running config I see:
group-policy abcd attributes
banner none
wins-server value 123.123.123.123
dns-server value 123.123.123.123
dhcp-network-scope none
vpn-access-hours none
vpn-simultaneous-logins 3
vpn-idle-timeout 60
vpn-session-timeout 1200
What I need to do next to get this working short of a recycle of the ASA.
Cisco WAN :: 1941 Router Frozen From Time To Time?
Jun 29, 2011Ciso 1941 router frozen once a day, sometimes after 2 to 7 days. When the router frozen, no internet connection and cannot login/ping ethernet ports. I can login to console port and copy the error messages below. Reload the router and it will return back to normal operation. Re-installed IOS but still the same.
IOS Version 15.1(2)T2,
Cisco CISCO1941/K9 (revision 1.0) with 487424K/36864K bytes of memory.
DRAM configuration is 64 bits wide with parity disabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
[code]...
Router Has To Be Reset Every-time To Connect Laptop
Aug 31, 2012Every time I switch on one of our laptops it will not connect, once the router is restarted it works fine. We have 4 other devices which happily connect to the wireless connection first time.
View 2 Replies View RelatedConnect To 2 Wireless Connections From One Laptop At Same Time?
Nov 9, 2011I have two wireless connections at home from 2 different ISPs. How can make my laptop connect to both routers at the same time to make use of them?
View 1 Replies View RelatedHome Network :: How To Connect Two Lans At Same Time
Apr 11, 2011I have my PC in my office with two lans,, one, the internal lan of my company with a static ip address, the other one a broadband line for connecting to internet.. If i switch on both the lans at the same time, i am able to use the broadband lan and the internal lan stops functioning,, to make it work i need to disable the lan with broadband line.. i even tried bridging the lans but that again stopped my internal lan. way to connect both the lans at the same time so that both the networks work simultaneously... and if there is any other option to function two lans on a single PC at the same time.
View 19 Replies View RelatedLinksys Wireless Router :: Wrt54g2 Wifi Stops Working From Time To Time
Oct 26, 2011I have WRT54G2 router. All settings are more-less default and the behavior is following.You start up the router. If you do not connect wireless device within 10 minutes, then you have to restart the router.You have assigned IP via wifi, and when you connect cable device to the router, the wifi PCs are disconnected.
View 3 Replies View RelatedLinksys Cable / DSL :: X2000 Current Time Will Not Stay Set To Time Zone
May 1, 2012I recently purchased a X2000 ADSL modem/router combination. For some reason the current time will not stay set to the time zone. Rebooting clears the discrepancy for a short time before it drops an hour exactly. I'm in the central time zone and the setting are correct on the basic setup.?
View 1 Replies View RelatedLinksys Cable / DSL :: Retrieving Up-time / DSL Connection Time Information From WAG320N
Jan 17, 2012Is the WAG320N iPv6 compatable ? ,or could it be with a firmware update ?.Is the X2000 in the same boat in iPv6 terms as th WAG320N ?.Is there a way of retrieving "UPTIME" / "DSL connection time" information from the WAG320N and also line attenuation stats etc.Wouldn't need the above but poor isp needs keeping an eye on.
View 3 Replies View RelatedConnect 2 Wireless Access Point As Same Time To One Laptop
Mar 22, 2012is it possible to connect 2 wireless access point as same time to one laptop.
View 2 Replies View RelatedRun An Avast Boot Time Scan And Now Won't Connect To Router?
Nov 21, 2011When I look at the local area connection the status is acquiring network address and just sits there. When I try to repair, it states that windows couldn't finishing repairing because it can't renew my IP address.
View 7 Replies View Related