Linksys Cable / DSL :: Retrieving Up-time / DSL Connection Time Information From WAG320N

Jan 17, 2012

Is the WAG320N iPv6 compatable ? ,or could it be with a firmware update ?.Is the X2000 in the same boat in iPv6 terms as th WAG320N ?.Is there a way of retrieving "UPTIME" / "DSL connection time"  information from the WAG320N and also line attenuation stats etc.Wouldn't need the above but poor isp needs keeping an eye on.

View 3 Replies


Linksys Cable / DSL :: WAG320N - Drops DSL Connection Each Time Connect

Jul 19, 2011

This is a bit of a pain as the behaiviour is not consistent. whenever I connect to the Device webpage a number of things may happen
1. There is no connection - the page tries to load but never does. While this happens the router drops the ADSL connection and re-connects. I have to close the browser session and try again later. OR
2. The Browser session connects but at some point after the connection, say when I am trying to save changes or even just browsing through the config pages the session hangs, and again the router drops the ADSL connection and re-connects. I have to close the session and try again later.
I have noticed this happens when I use my OpenSuse  11.4 Linux Box using Firefox 5 or even using my Win 7 Box using IE9.

View 4 Replies View Related

Linksys Cable / DSL :: Set Time Manually On WAG320N?

Sep 10, 2010

How do I set the time on my WAG320N manually. I have set the time zone, but the time shown is 04-01-2000 15:33:52, and I can't find anywhere to correct this.

View 8 Replies View Related

Linksys Cable / DSL :: WAG320N Block URL By Time Of Day?

Jun 27, 2011

I have set up an access restriction profile by time of day, but it seems that the web sites I list are blocked regardless of the time of day. Does the WAG320N apply the time of day to the blocked URLs or is the time of day only applicable to internet access?

View 1 Replies View Related

Linksys Cable / DSL :: Confirm Time Set On WAG320N?

Jul 19, 2011

how to confirm the time that is et on a WAG320N ?I have several wireless devices with scheduled restriction times and they don't appear to be functioning correctly.

View 1 Replies View Related

Linksys Cable / DSL :: Disable Some Pc At Night Time Using Wag320n

Oct 7, 2011

our kids at home always hugs the internet at night time, which is way past their bed time. i have been trying to disable their internet connection during night time only. im getting concerns what their watching at night or who their chatting with at 3am

View 4 Replies View Related

Linksys Cable / DSL :: X2000 Current Time Will Not Stay Set To Time Zone

May 1, 2012

I recently purchased a X2000 ADSL modem/router combination.  For some reason the current time will not stay set to the time zone.  Rebooting clears the discrepancy for a short time before it drops an hour exactly.  I'm in the central time zone and the setting are correct on the basic setup.?

View 1 Replies View Related

Linksys Cable / DSL :: WAG160N Modem Just Dropped Wireless Connection Constantly In Various Time Period

Sep 28, 2012

I've bought a "WAG160N v1.0 Annex A" almost 2 years ago. I never used it's wireless feature untill we moved our house. Now it's like 4 month I'm using its wifi feature and I've got to admit I'm really frustrated by its functionality!
For months the modem just dropped wireless connection constantly in various time periods. Somtimes it went like 2 days without any problem but some other times I had to change channel every 15 minutes for it to get back working. And yes it didn't get fix until I changed the channel, otherwise clients had to wait several hours for a 50/50 chance of reconnection. Now It's two days the changing channel trick no longer works. I tried all channels and even put my notebook next to the modem but no luck. The notebook sometimes connnects to the access point but disconnects after a few seconds. Somtimes it doesnt even detect the SSID of my WAG160N modem. Some friends suggested that the wireless hardware of my modem is broken and no longer works but I'm eager to know if it is broken why is it still broadcasting and sending signal.
I've tried everything from upgrading and downgrading firmware to turning on and off the modem several times and changes modem position. And even tried the G-only 20MHz mode.We are at a very crowdy place. Using inSSIDer I could pick about 15 other access points. Only few of them are using Wireless-N, most of them are using Wireless-G.This is the inSSIDer diagram of my WAG160N modem from a client: [code]

View 5 Replies View Related

Linksys Wireless Router :: Wrt54g2 Wifi Stops Working From Time To Time

Oct 26, 2011

I have WRT54G2 router. All settings are more-less default and the behavior is following.You start up the router. If you do not connect wireless device within 10 minutes, then you have to restart the router.You have assigned IP via wifi, and when you connect cable device to the router, the wifi PCs are disconnected.

View 3 Replies View Related

Home Network :: Connection Between Router And Cable Modem Goes Off At Specific Time?

Jul 20, 2011

Lately I've been experiencing connection problems between my router and cable modem. Every night after 11:00 PM EST, my Internet connection sporadically goes out. I called my ISP who said there was nothing wrong on their end. Plugging directly into my modem allows me to access the Internet. When I wake up in the morning, the connection is back until 11 or later again. I ran WireShark but I'm not sure what to be looking for. There are a lot of random things from the LLMNR protocol like standard query A zmtvrjaql.

View 2 Replies View Related

Linksys Cable / DSL :: Current Time Not Available X3000?

Oct 13, 2012

regarding Current Time Not Available. I loose internet connecting for hte last 5 weeks, My ISP is good. Bit I have noticed Current Time Not Available and when this happens my internet looses connection. but does state still connected. Using v1.0.03 build 001 Jun 11,2012 can we set manually the time?

View 9 Replies View Related

Linksys Cable / DSL :: WAG320N And Cable Modem Connection?

Jun 4, 2010

some reference material about configuring my WAG320N to use my cable modem via Ethernet port 1. I've seen it mentioned that's its possible, however I've been unable to sort it out myself.
And before you ask, I've brought the DSL router as I'm moving in the next 12 months and my new base will not have access to cable internet and I'll be reverting back to DSL.

View 8 Replies View Related

Linksys Cable / DSL :: Wag120n Internet Speed Drops With Time

Aug 10, 2012

I am using linksys cisco wag120n adsl2 modem router.When I start the router the internet speed seems great but after some time the speed drops miserably. When I again restart the router the speed seems great for few mins but again drops after sometime.It happens in both LAN and wireless mode.The firmware version of the router is 1.00.16
I was going through the problems posted by some other user but observed that cisco people are not heraing to them.Seems made a mistake by associating with cisco product.This is the worst router I have ever used.The wireless also gets disconnected abruptly.Next time I'll avoid cisco.Cisco is all about stone age products and zero customer care.

View 1 Replies View Related

Linksys Cable / DSL :: X3000 - Can't Find Time Zone For Middle East

Nov 3, 2012

why it's not included in the setup of the router ? I can only see (GMT+04:00) Armenia and nothing else !!

View 1 Replies View Related

Linksys Cable / DSL :: WAG160Nv2 Slow Wireless Speed And Wrong System Time

Aug 23, 2010

I have a WAG160Nv2 with Firmware Version:V2.00.20 Two problems
1. Slow wireless speed - only 2Mbit - with cabte up to the lines max 15Mbit
2. The routers system time is wrong - it says " 03-01-2000 02:19:54" I have set the correct system time but no difference
I have tried a lot of wireless options and some of the timezones but i did not solve the problem

View 8 Replies View Related

Linksys Cable / DSL :: WAG320N DSL Connection Lost

Mar 26, 2011

I have been using a WAG320N since January. Around a week ago I came home to find the unit attempting to reconnect every few minutes - the DSL light flashing but nothing happening.
I replaced with an old Belkin unit which worked fine straight away.
i have upgraded the firmware, which made no difference, and secondly, tried a brand new unit, which strangly had the same problem even though the ancient belkin unit works first time and my original cisco unit worked for a couple of months before failing.
Are there any settings that relate to the DSL connection that may have been reset on the original unit? Could this be an issue related to signal quality or anything similar?

View 5 Replies View Related

Linksys Cable / DSL :: See Duration Of Internet Connection On WAG320N?

May 23, 2011

Everytime I post this message it keeps leaving out the contents...think it might be an IE9 issue.Does anyone know if its possible to see the duration of the internet connection on a WAG320N?

View 4 Replies View Related

Linksys Cable / DSL :: WAG320N Loosing Internet Connection?

Dec 18, 2009

I've recently upgraded from a WAG54GS to the WAG320N. It seems to work OK for a period then looses the connetion to the Internet - DSL light on but not the Internet light. Normally I need to re-set the router to re-connect (either through the back switch or through the setup page)
This is my DSL information from [URL] whilst connected OK
--- System Information ---Vendor: LinksysModelName: WAG320NFirmware Version: 1.00.08 , 2009-08-27T19:37:13Boot Version: 1.06Hardware Version: 0.01--- DSL Information ---DSL Driver Version:  AnnexA version - A2pB023k.d21dDSL VPI/VCI:         0/38DSL Status:          ShowtimeDSL Mode:            ADSL2+DSL Channel:         DSL Upstream Rate:   1023 KbpsDSL Downstream Rate: 18723 Kbps                      Down         up    DSL Noise Margin:     9.1 dB       6.7 dBDSL Attenuation:     22.5 dB      12.0 dBDSL Transmit Power:  19.0 dBm     12.5 dBm--- Wireless Information ---Wireless Driver Version: Status: EnabledWireless Wide Channel: 9Wireless Standard Channel: 11- 2.462GHZWireless SSID: irae_2--- Dynamic Information ---LAN Mac Address: 00:22:6B:F5:6F:A7WAN Mac Address: 00:22:6B:F5:6F:A9Wireless Mac Address: 00:22:6B:F5:6F:A8---    
When the modem looses connection to the Internet; the DSL Noise Margin drops way down to 0.0 or 0.5.

View 9 Replies View Related

Linksys Cable / DSL :: WAG320N Set First Ethernet Port To WAN And Got Connection

Apr 4, 2011

Got BT Infinity installed today, thought I would ditch the Home-hub 3 and go back to my tried and tested WAG320N. Got it configured, set the first ethernet port to WAN and got a connection.Ran speed and comes out at 26Mbit.using the Home-hub 3.0 I get 37.5MBit.

View 4 Replies View Related

Cisco WAN :: 2621 / Time-Based Access Lists Using Time Ranges?

Jan 4, 2011

I have one 2621 router i want to creat time base access list so that one of my subnet user( use only internet between 11am to 2pm.

View 15 Replies View Related

Cisco Wireless :: WAP321 Lost Time - Cannot Sync With Time Server

Jul 8, 2012

I just bought a WAP321 Wireless AP. I wonder why it cannot sync with our time server automatically. Every time I reboot it, the system time become "Fri Dec 31 1999 12:00:00 UCT".  I have to do the sync manually by clicking on the "Save" button under the menu Administration > Time Setting.

View 5 Replies View Related

Linksys Cable / DSL :: WAG320N / Setup Connection Between Routers Over Internet?

Apr 26, 2011

Is it possible to setup a router to router connection over the internet with fixed IP Addresses with two WAG320N?

View 3 Replies View Related

D-Link DIR-825 :: Wireless Signal Drops From Time To Time?

Jan 10, 2012

AI have a Dir-825 router. The 5GHz is turned off and the wirless is on G/N. I have shawcable for my isp and my firmware is 2.06 and its a Rev B Router. I also have Qos Engine on for allowing me to have 2 xboxes on Open NAT.problem is my wireless signal for some wired reason is VERY weak. A while ago it used to work really far way outside. It was around 150ft distance at 4 bars. Now for some reason I can't even go upstairs without getting a 1 or 2 bar signal.

View 3 Replies View Related

D-Link DIR-655 :: Wireless Network Gets Slow Time To Time

Sep 1, 2011

i have had my dir-655 one year now, have never had wireless problems with it until notebook's internet gets very slow somedays, i just restart my router and then internet speed works normally.i have:

Hardware Version: A4 - Firmware Version: 1.32EU

View 5 Replies View Related

Cisco WAN :: 1941 Router Frozen From Time To Time?

Jun 29, 2011

Ciso 1941 router frozen once a day, sometimes after 2 to 7 days. When the router frozen, no internet connection and cannot login/ping ethernet ports. I can login to console port and copy the error messages below. Reload the router and it will return back to normal operation. Re-installed IOS but still the same.
IOS Version 15.1(2)T2,
Cisco CISCO1941/K9 (revision 1.0) with 487424K/36864K bytes of memory.
DRAM configuration is 64 bits wide with parity disabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)


View 5 Replies View Related

Making Time Warner Cable To Use A Pre-existing Cable Line?

May 29, 2012

Is it possible for Time Warner Cable to use a pre-existing cable line which is going into my cable box to hook up a modem so I can have Internet? I've got a modem in another room but I don't want a cable running down my hallway for 30 feet.

View 6 Replies View Related

Linksys Wireless Router :: E4200 Dropping Connection After Some Time

Nov 15, 2011

I bought a e4200 router about 3 weeks ago and after a power outage it decided it didnt like being connected to the internet anymore. So i got on the phone with cisco they determined the router was no good, mind you my laptop would connect wired. So they sent me a "refurbished" one, so i set it up. The new setup was wonky because it said the same message "Your connected to your router but..." then after trying to get the connection its self and failing it came up with "congratulations you are now connected to the internet". That lasted 3hrs and 45mins then died, so i went upstairs to power cycle it, it decided to connect with the old settings. That lased 25mins then died, so i reset it and reconfigured the router. Wouldnt connect, i checked my mac address and it was using my wireless one and kept turning on my wireless connection durring the install. So i cloned my wired mac address and got the internet for roughly an hour... then it died. So i reset it again and kept the wifi off got it going and decided to go to sleep. I wake up and its still working after 8hrs, i go down stairs with my tablet and i dies again. This time it refuses to reconnect, refuses to reset back up just doesnt want to work.

View 3 Replies View Related

Linksys Wireless Router :: E1000 Loses Connection All Time

Nov 19, 2011

At home I have 3 computers and 2 mobile phones that connects to wifi network.Often, if I open up one of the computers that is sometimes off (laptop), then the network connection doesn't work anymore. I can still see the network in wifi choices on any device, but it won't connect to the Internet.

View 9 Replies View Related

Linksys Cable / DSL :: WAG320N With 100 Mbps Fiber Is Not Establishing Full Duplex Connection

Feb 26, 2011

I have 100 mbps fiber connection. I bought 320N today I bought 320N and here is the problem:
We have a switch in the building. I am getting connection via CAT5. So I choosed "Use as WAN Port" from Ethernet settings. There is not much you can do here. I just used PPPoE and connected internet without any problem. The problem is I am only getting 32mbps. When I connect CAT5 cable directly to my computer I am getting 92mbps.
Maybe WAG320N is not establishing a full duplex connection.

View 3 Replies View Related

Linksys Wireless Adapters :: AE2500 - Needs To Restart Modem Every Time For Connection

Aug 27, 2011

So I just got hooked up to the internet via qwest the other day with my room mate.  We have a wireless modem (PK5000) and he's using the AE2500 usb adapter to get online.  Now, he can get online, but if he ever turns off or sleeps his computer, he can't connect when he turns it back on.  His computer can see the network, full signal, but when he tries to connect it says cannot connect and under troubleshoot options suggests we should move his computer closer to the modem, but its only about 20 feet away and shows full signal.  To get it to work, we need to go into the modem config and reset the wireless options.  No changes are made, just scroll to the bottom and click apply, and presto change he can connect with no problems.He's running windows 7 home edition 64 bit.  The modem's security is WPA/WPA2.

View 1 Replies View Related

How To Find IP Address From Time Warner Cable

Nov 6, 2011

we just switched over to time warner. We need the IP address to set up our surveillance cameras. Is there any way to get that online?

View 2 Replies View Related

Clear 4g Wireless Versus Road Runner / Time Warner Cable Internet

Jan 2, 2012

I have a home made desktop I use for work so I use a dsl modem (my laptop wireless ofcourse) I was thinking of switching to Clear...Any thoughts? I have TWC roadrunner and its the 3 way package (net, phone, cable) But I watch my shows online cable is over-rated for us tech nerds...

View 1 Replies View Related

Linksys Wireless Adapters :: WRT120N - Lose Wireless Connection Every Time The Computer Reboots?

Mar 26, 2013

I have a Cisco WRT120N Router and a Cisco Valet AM10 wireless adapter. Almost every time the computer reboots, I loose my network and I have to redo the AM10 setup. The AM10 is the only device that loses the connection, my lap top and printer do not lose the connection.

Problem 2: Everytime I upplug and replug the AM10 a window pops up saying I need to check the drive for errors but none
are found.

Problem 3: I downloaded the AM10 install program, Downloadable.Setup.AM10.1.2.10148.2. It does not work. If I try to run it Iget an error message that the setup canot be completed and to call in for support.

Problem 4: When I can get it working is shows that it is Wireless Connection 5. Why 5 and not 1? Where are the other 4?

<script id="overlay_tmpl" type="text/html">// <div id="<%= overlayId %>" class="_mp3rocket_overlay_style" style="left: <%= overlayLeft %>; top: <%= overlayTop %>; width: <%= overlayWidth %>; height: <%= overlayHeight %>"></div> // </script>

View 5 Replies View Related

Copyrights 2005-15, All rights reserved