Linksys Cable / DSL :: WAG320N Loosing Internet Connection?

Dec 18, 2009

I've recently upgraded from a WAG54GS to the WAG320N. It seems to work OK for a period then looses the connetion to the Internet - DSL light on but not the Internet light. Normally I need to re-set the router to re-connect (either through the back switch or through the setup page)
 
This is my DSL information from [URL] whilst connected OK
 
--- System Information ---Vendor: LinksysModelName: WAG320NFirmware Version: 1.00.08 , 2009-08-27T19:37:13Boot Version: 1.06Hardware Version: 0.01--- DSL Information ---DSL Driver Version:  AnnexA version - A2pB023k.d21dDSL VPI/VCI:         0/38DSL Status:          ShowtimeDSL Mode:            ADSL2+DSL Channel:         DSL Upstream Rate:   1023 KbpsDSL Downstream Rate: 18723 Kbps                      Down         up    DSL Noise Margin:     9.1 dB       6.7 dBDSL Attenuation:     22.5 dB      12.0 dBDSL Transmit Power:  19.0 dBm     12.5 dBm--- Wireless Information ---Wireless Driver Version: 5.10.85.0.cpe4.402.4Wireless Status: EnabledWireless Wide Channel: 9Wireless Standard Channel: 11- 2.462GHZWireless SSID: irae_2--- Dynamic Information ---LAN Mac Address: 00:22:6B:F5:6F:A7WAN Mac Address: 00:22:6B:F5:6F:A9Wireless Mac Address: 00:22:6B:F5:6F:A8---    
 
When the modem looses connection to the Internet; the DSL Noise Margin drops way down to 0.0 or 0.5.

View 9 Replies


ADVERTISEMENT

Linksys Cable / DSL :: WAG320N Loosing Internal Settings After Power Reset?

Dec 19, 2010

I recently bought the WAG320N and initial setup (Wizard) went fine ....(I selected all the defaults as presented to me so I did not afterwards modify anything on the settings)However ...when powering off (and back on) the device , my Dreambox Sattelite units (DM500) could not get access to the internet anymore (outbound) on port 12000.All other internet traffic went fine ...through browser, wireless, ...all Ok.....I tried everything to resolve but ultimately only succeeded in re-configuring from sracth. powered off the device and brought it back up ....same symptons.Did a hard-reset (back to factory defaults), reconfigured through wizard and ...all Ok again .....until I powered the device off and back on .....I have come to a point now where I excluded all possible 'surrounding' disturbing factors (eliminated switches etc ....and only connected 1 Dreambox unit directly to the device) and ....same symptons ....when powering off/on, the dreambox cannot get out anymore and re-configuring from sracth resolves ....until the next power off/on.And ...it is really the power off/on handling (reboot procedure WAG320N ?) that is causing it .....(I disconnected the DSL line and put it back in , forcing the modem to reconnect DSL and then all still works Ok ). ? It seems as if certain -internal- settings get lost after a power shutdown.....but why specifically port 12000 ?

View 5 Replies View Related

Linksys Cable / DSL :: WAG320N - Loosing Internal Settings After Power Reset

Aug 25, 2011

I recently bought the WAG320N and initial setup (Wizard) went fine ....(I selected all the defaults as presented to me so I did not afterwards modify anything on the settings)
 
However ...when powering off (and back on) the device , my Dream box Satellite units (DM500) could not get access to the internet anymore (outbound) on port 12000.

All other internet traffic went fine ...through browser, wireless, ...all OK.....I tried everything to resolve but ultimately only succeeded in re-configuring from scratch. This solved the issue .....until ....right...I powered off the device and brought it back up ....same symptoms. Did a hard-reset (back to factory defaults), reconfigured through wizard and ...all OK again .....until I powered the device off and back on .....

I have come to a point now where I excluded all possible 'surrounding' disturbing factors (eliminated switches etc ....and only connected 1 Dream box unit directly to the device) and ....same symptoms ....when powering off/on, the dream box cannot get out anymore and re-configuring from sracth resolves ....until the next power off/on.

And ...it is really the power off/on handling (reboot procedure WAG320N ?) that is causing it .....(I disconnected the DSL line and put it back in , forcing the modem to reconnect DSL and then all still works OK ). It seems as if certain -internal- settings get lost after a power shutdown.....but why specifically port 12000 ? (and ...no...I did not setup any port forwarding not triggering.

View 7 Replies View Related

Linksys Cable / DSL :: WAG200G - Keep Loosing Internet Connection?

Mar 1, 2012

My IP provider has upgraded my broadband speed in early Jan. They require ADSL2. It seems to coincide with this date that I keep loosing my internet connection on a regular basis, say every 2 days or so, but not consistent. The cure is to unplug the linksys WAG200G ADSL home gateway. Plug it in again and all is well, until the next time. On the box it says the until is ADSL2/2+ compliant.

View 2 Replies View Related

Linksys Cable / DSL :: Cisco X3000 Keeps Loosing Internet Connection?

Sep 19, 2012

My Cisco X3000 keeps loosing the internet connection after 1 day and will only reconnect if the device is rebooted.  Pressing the Internet connect button in the Status page does nothing.Even when the Internet connection is lost, the wireless network is working 100% and all the devices on the network stays connected and are accessible.The router has been updated to the latest Firmware available from Cisco v1.0.03 build 001 Jun 11,2012

View 9 Replies View Related

Linksys Cable / DSL :: See Duration Of Internet Connection On WAG320N?

May 23, 2011

Everytime I post this message it keeps leaving out the contents...think it might be an IE9 issue.Does anyone know if its possible to see the duration of the internet connection on a WAG320N?

View 4 Replies View Related

Linksys Cable / DSL :: WAG320N / Setup Connection Between Routers Over Internet?

Apr 26, 2011

Is it possible to setup a router to router connection over the internet with fixed IP Addresses with two WAG320N?

View 3 Replies View Related

Linksys Cable / DSL :: WAG320N And Cable Modem Connection?

Jun 4, 2010

some reference material about configuring my WAG320N to use my cable modem via Ethernet port 1. I've seen it mentioned that's its possible, however I've been unable to sort it out myself.
 
And before you ask, I've brought the DSL router as I'm moving in the next 12 months and my new base will not have access to cable internet and I'll be reverting back to DSL.

View 8 Replies View Related

Linksys Cable / DSL :: WAG320N DSL Connection Lost

Mar 26, 2011

I have been using a WAG320N since January. Around a week ago I came home to find the unit attempting to reconnect every few minutes - the DSL light flashing but nothing happening.
 
I replaced with an old Belkin unit which worked fine straight away.
 
i have upgraded the firmware, which made no difference, and secondly, tried a brand new unit, which strangly had the same problem even though the ancient belkin unit works first time and my original cisco unit worked for a couple of months before failing.
 
Are there any settings that relate to the DSL connection that may have been reset on the original unit? Could this be an issue related to signal quality or anything similar?

View 5 Replies View Related

Linksys Cable / DSL :: WAG320N Set First Ethernet Port To WAN And Got Connection

Apr 4, 2011

Got BT Infinity installed today, thought I would ditch the Home-hub 3 and go back to my tried and tested WAG320N. Got it configured, set the first ethernet port to WAN and got a connection.Ran speed test.net and comes out at 26Mbit.using the Home-hub 3.0 I get 37.5MBit.

View 4 Replies View Related

Linksys Cable / DSL :: WAG320N - Drops DSL Connection Each Time Connect

Jul 19, 2011

This is a bit of a pain as the behaiviour is not consistent. whenever I connect to the Device webpage a number of things may happen
 
1. There is no connection - the page tries to load but never does. While this happens the router drops the ADSL connection and re-connects. I have to close the browser session and try again later. OR
 
2. The Browser session connects but at some point after the connection, say when I am trying to save changes or even just browsing through the config pages the session hangs, and again the router drops the ADSL connection and re-connects. I have to close the session and try again later.
 
I have noticed this happens when I use my OpenSuse  11.4 Linux Box using Firefox 5 or even using my Win 7 Box using IE9.

View 4 Replies View Related

Linksys Cable / DSL :: WAG320N Internet LED Failed

Mar 11, 2010

After a very painful 20 minutes on Linksys tech chat with somebody who didn't listen to what i was telling them ... i thought i'd come on here and ask.I have just bought a WAG320N,the admin panel tells me I'm connected Yet the Internet LED is NOT lit on my router.

View 5 Replies View Related

Linksys Cable / DSL :: WAG320N With 100 Mbps Fiber Is Not Establishing Full Duplex Connection

Feb 26, 2011

I have 100 mbps fiber connection. I bought 320N today I bought 320N and here is the problem:
 
We have a switch in the building. I am getting connection via CAT5. So I choosed "Use as WAN Port" from Ethernet settings. There is not much you can do here. I just used PPPoE and connected internet without any problem. The problem is I am only getting 32mbps. When I connect CAT5 cable directly to my computer I am getting 92mbps.
 
Maybe WAG320N is not establishing a full duplex connection.

View 3 Replies View Related

Linksys Cable / DSL :: WAG320N Sending Wake-On-LAN From Internet

Jan 26, 2011

I'm currently on market to get a new ADSL/WLAN/Ethernet router to my home office and I'm looking at the WAG320N as it is all-in-one solution and also 1G ethernet ports for fast file transfer. My setup is that couple PC:s and PS3 is connected with WLAN and a NAS with RAID2 is connected with ethernet cable. The thing I would like to do is allow subnet directed broadcasts from WAN side so I could use wake-on-lan feature to turn my NAS on from remote location. Does the WAG320N option  "Filter Multicast" has this capability so I can send "magic packet" from Internet to turn on my NAS? How to test the WAG320N to use WOL from internet side?

View 3 Replies View Related

Linksys Cable / Dsl :: Internet Sharing Through Wifi On Wag320n

Feb 12, 2011

I have a problem with my ADSL modem router WAG320N for internet sharing . I want to connect internet cable by RJ-45 port to my modem and receive internet on other WiFi enabled devices. It means I want to utilize my router modem as an access point. Is it possible to use this device as an access point ?

View 1 Replies View Related

Linksys Cable / DSL :: WAG320N FTP Server Not Accessible From Internet

May 24, 2010

I`ve had a problem with my WAG320N for some time now.I`ve add a 1,5Tb hard drive to the usb and I can access it at LAN.Now I want to take it a bit further and be able access it from the outside.

View 9 Replies View Related

Linksys Cable / DSL :: WAG320N Internet Disconnects After Every 10 Hours

Mar 12, 2011

I bought my new router WAG320N two weeks ago and each morning after 10 hours operation I loose my internet connectivity I can't even remote into the router and press the connect button to connect to the internet again .I have to power cycle the modem to be able to connect to the internet again .? I though this may be ISP related put my old  adsl router plugged it in and ran for 2 days no disconnection.

View 1 Replies View Related

Linksys Cable / DSL :: Retrieving Up-time / DSL Connection Time Information From WAG320N

Jan 17, 2012

Is the WAG320N iPv6 compatable ? ,or could it be with a firmware update ?.Is the X2000 in the same boat in iPv6 terms as th WAG320N ?.Is there a way of retrieving "UPTIME" / "DSL connection time"  information from the WAG320N and also line attenuation stats etc.Wouldn't need the above but poor isp needs keeping an eye on.

View 3 Replies View Related

Routers / Switches :: Keep Loosing Connection With WLL Internet

Jul 27, 2011

I have recently changed my router from Netgear to TalkTalk because of an intermittent signal, no problem with my desktop ethernet or laptop wireless or tablet but I keep loosing connection with my WII internet connection for Netflix.

View 10 Replies View Related

D-Link DIR-825 :: Loosing Internet Connection On Wireless?

Oct 6, 2011

This router has to be rebooted every 12-24hrs to re-establish the internet connection. 

View 14 Replies View Related

Belkin Routers :: F9K1103 V1 Keeps Loosing Internet Connection

Jan 16, 2013

F9K1103 v1 (01C) keeps loosing internet connection, the router is wired to a time warner modem and wireless is not enabled.

View 2 Replies View Related

D-Link DIR-600 :: Loosing Internet Connection Highlighted By Many Users

Jan 28, 2012

Bought a Dir-600 from challenger, used it for 3 months and started expericing the common problems of loosing internet connection highlighted by many users here and in other forums. Would always have to do a modem / router power cycle to get it going again.Slightly after 3 months... the thing went dead. Can power up but no response. Cannot detect the modem.Got a one-for-one exchange at Funan. Used the 2nd one for less than 2 months. It just went dead on me! Same problem...

View 3 Replies View Related

Linksys Cable / DSL :: WAG320n Use As Modem Only?

Jul 17, 2011

I have a WAG320n and I wish to use it as a modem only so that I can use an Airport Extreme as my wireless router. how to configure the WAG320n so that it can be used in this configuration?

View 1 Replies View Related

Linksys Cable / DSL :: Setting Up VPN On WAG320N?

Mar 2, 2011

how to configure or set up VPN on WAG320N?

View 3 Replies View Related

Linksys Cable / DSL :: WAG320N Becomes Unresponsive?

Aug 27, 2012

I have an intermittent issue with a new WAG320N.Device is new (installed for 1 month now) and is running the latest firmware "out of the box".
 
Device was confirmed as working (recommended) via the ISP, as it uses a Broadcom chipset, so it works "more reliably" with the ISP's hardware which uses the same chipset.
 
Setup was painless and the router synced up fine and has been operating for a few weeks. However, twice in the past week the router has become unresponsive to ping over the LAN. Furthermore, the device's lights indicate everything is OK, however I have to reset the router (power cycle) and then it returns to normal.
 
WIFI is OFF. LAN IP is set manually, DHCP is OFF. The router is plugged into it's own UPS.

View 1 Replies View Related

Linksys Cable / DSL :: WAG320N Cannot Connect ISP

Mar 6, 2012

How to configure settings for router E4200I live in Finland and bought new Cisco Linksys WAG320n router modem as I am experienced Cisco user. However after spending several hours and setups on the WAG320n router I cannot get it to connect on the ISP ADSL line.

RFC2684 Bridged
LLC/SNAP
g.dmt or ADSL2+
VPI 0
VCI 100

But once I setup these or acutally any other setting I cannot get the router to connect. With the right settings I can get the DSL PVC status up and connected but the ModemRouter cannot connect and retrieve IP-address from ISP. 

View 7 Replies View Related

Linksys Cable / DSL :: WAG320n DMZ Does Not Function At All?

Sep 4, 2012

I'm trying to play some online games and my WAG320N does not forward ports, upnp does not function and to top it off DMZ wont even work (not a software firewall issue either). I have the latest firmware (and honestly the stock firmware is terrible).
 
Am I out of luck or is there something I can do to fix this? I sure as hell will be steering clear of linksys products after this.

View 1 Replies View Related

Linksys Cable / DSL :: Old Firmware 1.00.08 For WAG320N?

May 16, 2010

i need to downgrade my WAG320N and don't find old firmware 1.00.08 AnnexA

View 9 Replies View Related

Linksys Cable / DSL :: WAG320N Is Really Slow After Use

Mar 10, 2011

This WAG320N Router can get really slow after a while use which is really frustrating for me since I am a gamer. Power cycling it SOMETIMES does the trick but it will still get slow. It has been slow just now and over here it is midnight so the internet peak should be down and my internet should be faster but its now.

View 2 Replies View Related

Linksys Cable / DSL :: WPS On WAG320N When Update?

Nov 8, 2012

I have the WAG320N. I know if my router is updated to fix the bug of the WPS?There is an update? Which is the date scheduled for release? The vulnerability of my network has been compromised yesterday because of this bug, so either the update is released soon or I'll have to switch to another product of some companies more serious

View 3 Replies View Related

Linksys Cable / DSL :: WAG320N Is Very Slow?

Feb 4, 2011

Transferring a file between a wired Win 7 machine and a wireless Snow Leopard mac seems to top out at 32Mbps.I've seen over 60Mbps on this laptop using N networks before, and when I wire the laptop I get a more respectable 240Mbps (presumably maxing out the server's disk I/O rate), so I'd say the issue is the router.
 
Things I have already tried:updating the firmware to 1.00.125Ghz modeFinding the least crowded 2.4Ghz channelswide channelsSetting network mode to N-onlySetting the transmission rate to 108Mbpschanging the beacon interval to 50, the frag threshold to 2201 and the RTS threshold to 2202

View 2 Replies View Related

Acer Aspire 5250 Keeps Loosing Wifi Internet Connection?

Nov 27, 2011

I purchased a brand new Acer Aspire 5250-BZ669 that included Windows 7 just two days ago. Everything is working fine on it except for it randomly looses connection to the internet. I have an established network that I have been using for years. The signal strength is always 5 bars and excellent. I also have a compaq connected to the same network, and it never looses connection. However my Acer will randomly drop connection. I have no idea why. Sometimes it will connect again in minutes or sometimes hours. I am using a Linksys G Wireless Router(Model # WRT54G2), Atheros AR5B125 Wireless Network Driver, and a Atheros AR8152 Controller. I have enabled and disabled in addition to uninstalling and installing the driver and controller many times. I have also moved the router and adapter all over the house. I have downloaded the newest versions of every driver from the Acer website. I have googled for hours looking for the answer to no avail. I run the troubleshoot and the answer it gives me is to make sure all the connections to the router is secure, which it is or else my other laptop wouldn't work.

View 19 Replies View Related

Keep Loosing Connection With Linksys E3000 Router?

Jan 27, 2011

my linksys e3000 router loses connection quite often. E.G. we lost power last night and i tried resetting the router but it didnt work so I had to uninstall and then reinstall the router. A few other times it would lose connection for no apparent reason.

View 8 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved