I have a problem with my ADSL modem router WAG320N for internet sharing . I want to connect internet cable by RJ-45 port to my modem and receive internet on other WiFi enabled devices. It means I want to utilize my router modem as an access point. Is it possible to use this device as an access point ?
View 1 RepliesI just bought a macbook and want to connect with my WAG320N. I have no problem to connect on 54mbs what tells me that I'm on Wifi G. The settings in my router was on b/g/n so I changed it to just N but then it won't connect. I don't get error or nothing. I just doesn't connect. I tried all different kind of settings but no luck.
View 8 Replies View RelatedI'm going to buy a WAG320N router modem.I've read the manual but I haven't found an answer to the silly question: is it possible to completely disable wifi, and surf in internet using the 4 lan port only?
View 2 Replies View RelatedI need to connect 4 pc together and to the gateway (only one pc has wifi). i would know if it's possible to use one device like a router where i can wired the 4pc to put them in lan and use also this router to connect all the client to one gateway WAG320N.
View 3 Replies View RelatedI have a little problem with this modem / router WAG320NFrom 6 months now no problem, perfect.For a week now appears that wifi losing signal every 4 / 5 hours:Internet has no problem and the PC connected via Ethernet goes smoothly, while the wi-fi stuff (iphone,ipad,notebook) no longer see the network, but the lights on the modem (including wi-fi) are all green as they should be.To resolve this problem I turn off and on again and the wi-fi again be recognized and work fine for other 4 / 5 hours.i have the latest available firmware and settings areBand 2.4Ghz Mode B / G / N MixedLarge 40-MHz channel width,Wide channel 9 2452 GhzStandard.
View 2 Replies View RelatedI recently bought the WAG320N can I block Peer to Peer file sharing on my Network?
View 3 Replies View RelatedI bought my WAG320N, I too have the internet drop out and from reading in here is a very common problem. Cisco really should bring out a new firmware version and address this issue. Any way you can block peer to peer file sharing with the WAG320N? If so how do you go about it?
View 1 Replies View RelatedIs there a way to know from the web interface the wifi speed of the connected clients?
View 1 Replies View RelatedAfter a very painful 20 minutes on Linksys tech chat with somebody who didn't listen to what i was telling them ... i thought i'd come on here and ask.I have just bought a WAG320N,the admin panel tells me I'm connected Yet the Internet LED is NOT lit on my router.
View 5 Replies View RelatedI'm currently on market to get a new ADSL/WLAN/Ethernet router to my home office and I'm looking at the WAG320N as it is all-in-one solution and also 1G ethernet ports for fast file transfer. My setup is that couple PC:s and PS3 is connected with WLAN and a NAS with RAID2 is connected with ethernet cable. The thing I would like to do is allow subnet directed broadcasts from WAN side so I could use wake-on-lan feature to turn my NAS on from remote location. Does the WAG320N option "Filter Multicast" has this capability so I can send "magic packet" from Internet to turn on my NAS? How to test the WAG320N to use WOL from internet side?
View 3 Replies View RelatedEverytime I post this message it keeps leaving out the contents...think it might be an IE9 issue.Does anyone know if its possible to see the duration of the internet connection on a WAG320N?
View 4 Replies View RelatedI`ve had a problem with my WAG320N for some time now.I`ve add a 1,5Tb hard drive to the usb and I can access it at LAN.Now I want to take it a bit further and be able access it from the outside.
View 9 Replies View RelatedI bought my new router WAG320N two weeks ago and each morning after 10 hours operation I loose my internet connectivity I can't even remote into the router and press the connect button to connect to the internet again .I have to power cycle the modem to be able to connect to the internet again .? I though this may be ISP related put my old adsl router plugged it in and ran for 2 days no disconnection.
View 1 Replies View RelatedI've recently upgraded from a WAG54GS to the WAG320N. It seems to work OK for a period then looses the connetion to the Internet - DSL light on but not the Internet light. Normally I need to re-set the router to re-connect (either through the back switch or through the setup page)
This is my DSL information from [URL] whilst connected OK
--- System Information ---Vendor: LinksysModelName: WAG320NFirmware Version: 1.00.08 , 2009-08-27T19:37:13Boot Version: 1.06Hardware Version: 0.01--- DSL Information ---DSL Driver Version: AnnexA version - A2pB023k.d21dDSL VPI/VCI: 0/38DSL Status: ShowtimeDSL Mode: ADSL2+DSL Channel: DSL Upstream Rate: 1023 KbpsDSL Downstream Rate: 18723 Kbps Down up DSL Noise Margin: 9.1 dB 6.7 dBDSL Attenuation: 22.5 dB 12.0 dBDSL Transmit Power: 19.0 dBm 12.5 dBm--- Wireless Information ---Wireless Driver Version: 5.10.85.0.cpe4.402.4Wireless Status: EnabledWireless Wide Channel: 9Wireless Standard Channel: 11- 2.462GHZWireless SSID: irae_2--- Dynamic Information ---LAN Mac Address: 00:22:6B:F5:6F:A7WAN Mac Address: 00:22:6B:F5:6F:A9Wireless Mac Address: 00:22:6B:F5:6F:A8---
When the modem looses connection to the Internet; the DSL Noise Margin drops way down to 0.0 or 0.5.
Is it possible to setup a router to router connection over the internet with fixed IP Addresses with two WAG320N?
View 3 Replies View Relatedsome reference material about configuring my WAG320N to use my cable modem via Ethernet port 1. I've seen it mentioned that's its possible, however I've been unable to sort it out myself.
And before you ask, I've brought the DSL router as I'm moving in the next 12 months and my new base will not have access to cable internet and I'll be reverting back to DSL.
is it possible to moderate sharing bandwitch or/and traffic internet over wireless via WAG120N for some specific client? is there any configuration inside modem OS?without any external software such as Cyberoam or... that they need Always-On PC to work!
View 3 Replies View RelatedI have a WAG320n and I wish to use it as a modem only so that I can use an Airport Extreme as my wireless router. how to configure the WAG320n so that it can be used in this configuration?
View 1 Replies View Relatedhow to configure or set up VPN on WAG320N?
View 3 Replies View RelatedI have an intermittent issue with a new WAG320N.Device is new (installed for 1 month now) and is running the latest firmware "out of the box".
Device was confirmed as working (recommended) via the ISP, as it uses a Broadcom chipset, so it works "more reliably" with the ISP's hardware which uses the same chipset.
Setup was painless and the router synced up fine and has been operating for a few weeks. However, twice in the past week the router has become unresponsive to ping over the LAN. Furthermore, the device's lights indicate everything is OK, however I have to reset the router (power cycle) and then it returns to normal.
WIFI is OFF. LAN IP is set manually, DHCP is OFF. The router is plugged into it's own UPS.
How to configure settings for router E4200I live in Finland and bought new Cisco Linksys WAG320n router modem as I am experienced Cisco user. However after spending several hours and setups on the WAG320n router I cannot get it to connect on the ISP ADSL line.
RFC2684 Bridged
LLC/SNAP
g.dmt or ADSL2+
VPI 0
VCI 100
But once I setup these or acutally any other setting I cannot get the router to connect. With the right settings I can get the DSL PVC status up and connected but the ModemRouter cannot connect and retrieve IP-address from ISP.
I'm trying to play some online games and my WAG320N does not forward ports, upnp does not function and to top it off DMZ wont even work (not a software firewall issue either). I have the latest firmware (and honestly the stock firmware is terrible).
Am I out of luck or is there something I can do to fix this? I sure as hell will be steering clear of linksys products after this.
i need to downgrade my WAG320N and don't find old firmware 1.00.08 AnnexA
View 9 Replies View RelatedThis WAG320N Router can get really slow after a while use which is really frustrating for me since I am a gamer. Power cycling it SOMETIMES does the trick but it will still get slow. It has been slow just now and over here it is midnight so the internet peak should be down and my internet should be faster but its now.
View 2 Replies View RelatedI have the WAG320N. I know if my router is updated to fix the bug of the WPS?There is an update? Which is the date scheduled for release? The vulnerability of my network has been compromised yesterday because of this bug, so either the update is released soon or I'll have to switch to another product of some companies more serious
View 3 Replies View RelatedTransferring a file between a wired Win 7 machine and a wireless Snow Leopard mac seems to top out at 32Mbps.I've seen over 60Mbps on this laptop using N networks before, and when I wire the laptop I get a more respectable 240Mbps (presumably maxing out the server's disk I/O rate), so I'd say the issue is the router.
Things I have already tried:updating the firmware to 1.00.125Ghz modeFinding the least crowded 2.4Ghz channelswide channelsSetting network mode to N-onlySetting the transmission rate to 108Mbpschanging the beacon interval to 50, the frag threshold to 2201 and the RTS threshold to 2202
I have only purchased this modem a few days ago (upgraded from a working Netgear DGN2000 for Gigabit).... it's solid most the time except for once a day when it needs to be reset.
One morning I accessed a single website, only to find the next wouldn't come up. (approx 7:30am) Lastnight the net was working fine at 11:30pm.... Thismorning I woke up, checked my download manager to find that at 2:30am all queued downloads failed, so the ADSL dropped sometime inbetween then.
The LAN and Wifi still work fine, when I go into the settings and click "reconnect" nothing happens. I need to turn the modem off for a min before it works ok. There is no newer firmware as of yet to try.
I do not have a "storage" tab in my setup screen. I have Setup, Security, Wireless, etc. According to its manual there must be a Storage tab between security and wireless. Mine doesn't have it. USB drive is connected and I see "mywag320n" on the network but I can't access it because it requires login and password (which I guess I must set up from Storage tab )
View 8 Replies View RelatedI connected my Western Digital Studio II 2TB external harddrive which is formatted NTFS. I can access the drive and read it. But I can't write it. It says I do not have rights. I tried to get to be the owner of the device but it gave some kind of error.
View 2 Replies View Relatedmy device can connect to the wireless network. When i tried to setup the network again it says that no WLAN network found. I have not change any of the setting in the modem it just can't find any WLAN network. I have tried reseting the modem but still no network found.
View 4 Replies View RelatedI need to configure my modem router wag320n let pass the magic packet to turn on my computer from the internet. I've already opened the door 7 to the computer ip but does not work. The bios and the OS are perfectly configured.
View 8 Replies View RelatedI have recently bought a WAG320N modem Gigabite router to substitute the modem router supplied by the internet service provider (in theory less performant).
Formerly I have a wireless router Zyxel (MOD. P660HW-D1). The main computer is wired (connected trough ethernet), I have also a NAS device (WD mybook world 1TB with Twonky as server) wired and a third wired connection for the above mentioned PLK 300. The PLK 300 (4 Inputs and one output) is used to connect a TV (Sony BRAVIA) a Bluray (SONY) a PS3 (Sony) and a multimedia HD (DVICO). All this was working properly. I have internet access from TV, PS3,... I was able to run videos, photos,... stored in the NAS from TV,....
I decided to change for improving the transfer speed and to allow a better wireless connection (I have initially coverage problems, but because I only use the wireless rarely...).Initially I bought a Linksys E 3000 (I thought it was possible to connect it directly to internet and not trough a modem. I asked to several people and in several shops but no one told me this was not possible). That was my first failure: I would like to suggest the liknsys people to clearly explain this on the product sheet to avoid that not very well informed people like me commit the same error.
Then I chaged the E3000 by the WAG320N. I connect the new modem-router like the former (Zyxel). No room for big errors, just the power, DSL line and ethernet cables. It works for the PC and the NAS but the PLC (PLK300) do not appears to work. Several tries later (including plugin the PLK on the line 1 input of the router it is shown on the network map but do not work. I do not have access to the internet nor to the NAS contents form TV,....
I go back to the former router and everything works again in the simplest way (I have internet access form TV,...) except the Twonky access to the NAS from TV ¿?. I do not know exactly what I have changed,...)
How do I set the time on my WAG320N manually. I have set the time zone, but the time shown is 04-01-2000 15:33:52, and I can't find anywhere to correct this.
View 8 Replies View Related