Bought a Dir-600 from challenger, used it for 3 months and started expericing the common problems of loosing internet connection highlighted by many users here and in other forums. Would always have to do a modem / router power cycle to get it going again.Slightly after 3 months... the thing went dead. Can power up but no response. Cannot detect the modem.Got a one-for-one exchange at Funan. Used the 2nd one for less than 2 months. It just went dead on me! Same problem...
We installed a DIR-615 Vers. E1 FV. 5.00NA and since then i-Pods and i-Pads keep dropping wi-fi connections. All wireless PC's and printers are working fine. We have configured the wireless as:Mixed 802.11 n,g and b. Auto channel csan enabled, using channel 6. Wireless security is WPA-Personnal. WPA is configured as Auto, TKIP and AES with a pre-shared key.
I have just purchased a DCS 2121 (I assume that it is a similar model to the DCS 920 in US).I have this setup:
- Connected the DCS 2121 wireless to my Belkin Router with a fixed IP address. Firmware version 1.4 is installed on the camera.
- I have a Synology 209 NAS server with surveillance station that I have connected to the Camera.
I all works fine for 5 minutes to a couple of hours at which point the DCS 2121 loose connection to the Router and does not try to reconnect. If I turn the Cam on and off it will reconnect - and then loose connection again af a short time.This is totally frustrating since the purpose of the Cam is to work as a surveillance cam - it kinda loose its value by not being connected...
Not sure where the best place to drop this question. It is a DIR-601 router. I have it configured in the virtual servers list as; internal system ip, public port/private port both 23, protocal tcp with inbound filter, allow all and schedule set to always. I have a second system with a different public port. I can connect to either one but after a short amount of idle time it appears to just drop the connection.
I have recently changed my router from Netgear to TalkTalk because of an intermittent signal, no problem with my desktop ethernet or laptop wireless or tablet but I keep loosing connection with my WII internet connection for Netflix.
My IP provider has upgraded my broadband speed in early Jan. They require ADSL2. It seems to coincide with this date that I keep loosing my internet connection on a regular basis, say every 2 days or so, but not consistent. The cure is to unplug the linksys WAG200G ADSL home gateway. Plug it in again and all is well, until the next time. On the box it says the until is ADSL2/2+ compliant.
I've recently upgraded from a WAG54GS to the WAG320N. It seems to work OK for a period then looses the connetion to the Internet - DSL light on but not the Internet light. Normally I need to re-set the router to re-connect (either through the back switch or through the setup page)
This is my DSL information from [URL] whilst connected OK
--- System Information ---Vendor: LinksysModelName: WAG320NFirmware Version: 1.00.08 , 2009-08-27T19:37:13Boot Version: 1.06Hardware Version: 0.01--- DSL Information ---DSL Driver Version: AnnexA version - A2pB023k.d21dDSL VPI/VCI: 0/38DSL Status: ShowtimeDSL Mode: ADSL2+DSL Channel: DSL Upstream Rate: 1023 KbpsDSL Downstream Rate: 18723 Kbps Down up DSL Noise Margin: 9.1 dB 6.7 dBDSL Attenuation: 22.5 dB 12.0 dBDSL Transmit Power: 19.0 dBm 12.5 dBm--- Wireless Information ---Wireless Driver Version: 188.8.131.52.cpe4.402.4Wireless Status: EnabledWireless Wide Channel: 9Wireless Standard Channel: 11- 2.462GHZWireless SSID: irae_2--- Dynamic Information ---LAN Mac Address: 00:22:6B:F5:6F:A7WAN Mac Address: 00:22:6B:F5:6F:A9Wireless Mac Address: 00:22:6B:F5:6F:A8---
When the modem looses connection to the Internet; the DSL Noise Margin drops way down to 0.0 or 0.5.
I purchased a brand new Acer Aspire 5250-BZ669 that included Windows 7 just two days ago. Everything is working fine on it except for it randomly looses connection to the internet. I have an established network that I have been using for years. The signal strength is always 5 bars and excellent. I also have a compaq connected to the same network, and it never looses connection. However my Acer will randomly drop connection. I have no idea why. Sometimes it will connect again in minutes or sometimes hours. I am using a Linksys G Wireless Router(Model # WRT54G2), Atheros AR5B125 Wireless Network Driver, and a Atheros AR8152 Controller. I have enabled and disabled in addition to uninstalling and installing the driver and controller many times. I have also moved the router and adapter all over the house. I have downloaded the newest versions of every driver from the Acer website. I have googled for hours looking for the answer to no avail. I run the troubleshoot and the answer it gives me is to make sure all the connections to the router is secure, which it is or else my other laptop wouldn't work.
My Cisco X3000 keeps loosing the internet connection after 1 day and will only reconnect if the device is rebooted. Pressing the Internet connect button in the Status page does nothing.Even when the Internet connection is lost, the wireless network is working 100% and all the devices on the network stays connected and are accessible.The router has been updated to the latest Firmware available from Cisco v1.0.03 build 001 Jun 11,2012
I have several computers and printers connected to a WRT120N router which is connected to 10mpbs DSL. The computers are all running WIN7 and are hardwired to the router. On the one PC, it keeps losing network connection. I've tried upgrading the router's firmware, reset, etc. to no avail.
I think it may be related to the same IP address being assigned to multiple machines connected to the router. Is there a way to set specific IP addresses to each item connected to the router to see?
I had the WAP610N for a few months with no issues. As always, I have a custom SSID and password, using WPA2. All of a sudden, none of my mobile units (at least 5) are unable to connect via the WAP610N. However, I can connect to a Netgear N750 w/o any issues. When I reboot the WAP610N, it resolves the issue for a few minutes, but then behaves the same as before. I know its not my network because, I am able to connect via wired and wireless via the Netgear. I verified via the web interface that none of the settings/configurations have changed - but still nothing. Latest firmware has been applied. Note sure If I should perform a factory reset or re-apply the firmware.
I have two WAP321s in my office. The network they are on is a single VLAN (172.16.10.x). Both WAPs are setup with the same SSID, and I have setup Single Point Setup.
I am having a problem that was happening before I setup Single Point Setup, and it is still happening. Basically wireless will be up and running fine for part of the day. Then people throughout the office will begin to lose their connections to the DHCP server. They still retain the connection to the WAP, but can no longer access the network.
The only way I have been able to fix this issue is to reboot the WAP. As soon as it reboots the connections come back. At first I thought it was due to the number of connections (which is why we now have 2 WAPs), however we only have about 20-25 conncurrent connections.
I put in the second WAP to try to balance out the load but this does not seem to be working. Is there a setting I need to change on the WAPs to balance out the load?
I Updated the 5508 from 7.0.230 to 7.4.100 and made it a cluster.Sinse the Update the handscanners loose the connection to the AS400 Application.Where to start troubleshooting?I did a debug client, I see the client is roaming but I can not say if there is a relation between roaming and loosing connection to the application.
My nephew's XBox (he's an on line gamer, and quite a serious one for that matter...) seems to boot him off line when someone uses the phone or goes on line on another computer. The house is quite far from the exchange so the average down speed is only 1.75-2 Mbps. This connection is through a BT Infinity R/S/F and I wanted to know if we could just add another R/S/F device and subnet the games console into it's own DMZ with full bandwidth access and then the normal broadband & phone on a different subnet also with full bandwidth access?
Ok, so if i open Utorrent and let it download for 10 minutes i loose my internet connection. I usually will disconnect my cat5 cable and plug it back in and it doesn't work so i would open up the CMD line and try to reset the network connection but it doesn't respond so the only way i can reset it is to restart the the computerI've tried reinstalling Utorrent but i still keep loosing my connection, yet all the while I am able to run netflix on my PS3 so my internet connection isn't going down.
my linksys e3000 router loses connection quite often. E.G. we lost power last night and i tried resetting the router but it didnt work so I had to uninstall and then reinstall the router. A few other times it would lose connection for no apparent reason.
im loosing connection every few minutes , tried ipconfig /release , ipconfig /renew and im getting this error every time : An error occurred while renewing interface Local Area Connection : unable to contact your DHCP server. Request has timed out. After typing ipconfig /all DHCP address is 255.255.255.255 and this IP 192.168.100.10. Tried other things like flushdns / netsh commands and nothing want to work. My connection works only after i restart my modem. Modem type Ubee 3236. The modem is new got it 4 days ago. And also why i cant access the modem configuration page by typing my default gateway in browser ?
We are in a hotel that allows us to use their router with a Hawking 300N expander. We seem to lose connection each time their router gets a new IP address. The router seems to lose connection frequently. Is there a setting in the expander that will allow the expander to "follow" the DHCP address of the router without having to take it down and go thru the setup each time.
I upgrade firmware from 184.108.40.206 to 220.127.116.11 and from this time I can't connect to any site time from to time. I have simple DHCP WAN connection between my provider and the router, my computer connects to router by wire (only Cisco SG 100D-08 stands between them). When I can't access sites I can access my router and the router needs much more time to answer to me via http. I don't use any vlans or internet access to my computer or router.
Im loosing connection every few minutes , tried ipconfig /release , ipconfig /renew and im getting this error every time : An error occurred while renewing interface Local Area Connection : unable to contact your DHCP server. Request has timed out. After typing ipconfig /all DHCP address is 255.255.255.255 and this IP 192.168.100.10. Tried other things like flushdns / netsh commands and nothing want to work. My connection works only after i restart my modem. Modem type Ubee 3236.
The router keeps loosing connection to the internet. I can still log into the router locally but cant connect out or in from the internet. Which is a big problem as i use this device remotely. I have tried different firmware (.9, .19, .27) the .19 seems to be the most stable but i am still having problems. The only way to rectify it is to reboot the router. Is there a fix for this or a way to schedule a reboot on the router.
I have a Belkin N600 model # F9K1102v1 i am loosing connection on all of the components connected to it wired or wireless. They all loose connection at the same time. I also noticed the clock in the router does not set to the correct time it is reading 1970 for the year and never changes.
have a HP 6500a All In One Printer in the network with a BERSR41 V3 router. I am using a Imac with this sytem for printing and scanning. For some reason I keep loosing the printer when I try to scan? I have it set to a static IP, and can not ping it, but can access the printer throught the network with the HP Utility. Am I missing something in setup on the router that causes it to keep loosing connection?
since a couple of days I've a strange behavior in my Spanning-Tree Topology.Every time I plug in a new Switch ( e.g. WS-2960S ) a topology change on my root bridge occurs and all client losing connection to the default gateway.The root bridge is also the default gateway.
Nov 28 11:14:12.865: STP: VLAN0001 Topology Change rcvd on Gi4/48 VLAN0001 is executing the ieee compatible Spanning Tree protocol Bridge Identifier has priority 0, sysid 1, address 0019.aa37.e040 Configured hello time 2, max age 20, forward delay 15 We are the root of the spanning tree
I just bought a "DLink Xtreme N Gigabit Router DIR-655" I configured it correctly. It works well for the wireless connection but my Lan connection (wired connection) does not work. The Lan computer connects to the router but cannot access the internet. All of my machines work OK with a Netgear G router, including the Lan computer.
We have a wireless router with about 8 devices connecting to it at any one time. For some reason, 1 laptop constantly loses internet service, it's still connected to the network but it's "local only" connection. Restarting the laptop doesn't solve the problem, only restarting the router.Now, I know very little about this kind of stuff, but to me it seems like an issue with IP addresses? It currently happens at least once a day.
I have a DIR-655, hardware B1, firmware 2.03NA. Sporadically, generally after the router has been on for 24 hours, I lose wireless Internet (WAN) connectivity. I can still connect just fine to the router interface. And if I plug in hardwired Ethernet, I can access the Internet just fine.I previously had a DIR-615 in operation with no problems.
-ISP modem Motorola SB6121 (stand-alone cable modem) -QoS/traffic shaping off; also disabled advanced DNS (tried OpenDNS as well as Comcast defaults) -DNS relay enabled -Using reserved IP addresses on the local network, all devices are set to DHCP -Enabled/disabled UPnP/multicast -Tried all firewall options, including disabling -Wireless using Mixed 802.11n/g; tried channel width 20/40 and just 20. Disabled auto channel scan and forced to -ch11. No other wireless interfering. Using WPA2 only, AES, with a 63char key. -Disabled WISH -Disabled WLAN partition, WMM enable, short GI. -Cat6 between modem and router
Again, hardwired LAN connection seems to be fine. I've already RMA'd the router once.When wireless Internet doesn't work, it seems to be all affected devices (iPhone/iPad/MacOS/WinXP/Roku).
So I have a DIR-655 and my internet connection drops every day. I have replaced the DIR-655 with a linksys just to try it and it works fine. This has happened with more than 1 of these 655''s. Also I have clients calling saying the wireless drops and it will not let them reconnect until I reboot the router. I have updated to the newest firmware with the same issues. I know its not bad cause I have more than 1 655 doing the same thing at a different location as well.
I bought this router a couple of months ago and it was working fine until this morning. I tried to use the internet and there was no connection at all (wired or wireless). I tried power cycling but that didn't work. I finally decided to call my DSL provider and we changed the setup from the router connecting to PPPOE to the modem connecting to PPPOE. Now, my two computers (wired) can access the internet but all my wireless devices (Android and BB) connect to the SSID (unique) but can't actually access the net.I called DLink but they decided to stop assisting me once I told them that my computers could connect but not the wireless devices. They said I need to call the manufacturers of my wireless devices - I really doubt that all 4 of my wireless devices are faulty.