Ubee 3236 XP Limited Or No Connectivity Loosing Connection Every Few Minutes
Nov 12, 2012
Im loosing connection every few minutes , tried ipconfig /release , ipconfig /renew and im getting this error every time : An error occurred while renewing interface Local Area Connection : unable to contact your DHCP server. Request has timed out. After typing ipconfig /all DHCP address is 255.255.255.255 and this IP 192.168.100.10. Tried other things like flushdns / netsh commands and nothing want to work. My connection works only after i restart my modem. Modem type Ubee 3236.
View 14 Replies
ADVERTISEMENT
Nov 12, 2012
im loosing connection every few minutes , tried ipconfig /release , ipconfig /renew and im getting this error every time : An error occurred while renewing interface Local Area Connection : unable to contact your DHCP server. Request has timed out. After typing ipconfig /all DHCP address is 255.255.255.255 and this IP 192.168.100.10. Tried other things like flushdns / netsh commands and nothing want to work. My connection works only after i restart my modem. Modem type Ubee 3236. The modem is new got it 4 days ago. And also why i cant access the modem configuration page by typing my default gateway in browser ?
View 4 Replies
View Related
Mar 4, 2013
Not sure where the best place to drop this question. It is a DIR-601 router. I have it configured in the virtual servers list as; internal system ip, public port/private port both 23, protocal tcp with inbound filter, allow all and schedule set to always. I have a second system with a different public port. I can connect to either one but after a short amount of idle time it appears to just drop the connection.
View 4 Replies
View Related
Dec 28, 2012
when im on my laptop and im on the internet,the connection goes from normal to Limited (yellow triangle caution sign by connection),non of the pages will load after that,i use diagnostics repair to fix the problem which works about 40% of the time,but is only temporary again.give it 5 minutes after the fix it happens again,diagnostics say the problem is with the wireless adapter card which is built into the laptop itself.i do and dont think this may be the cause since everything house loads perfectly fine but can have the occasional drop out aswell,on average i'd say it drops out about 10 times a day and i find it kind of frustrating.My Laptop is a Acer Aspire v3-531.My internet is with Virgin Media and i get around 60 MBps with them but the disconnections drop it to about 7mbps and keeps going down till the connection is actually gone.
P.S:The intel Proset wireless framework on this computer fails the hardware test straight saying the wirless hardware is not bound to the transport driver? what do i do?
View 14 Replies
View Related
Aug 16, 2012
We had a lightning strike near the house and it fried my NIC card (or so I thought), also my power strip. I replace them both along with my Ethernet cables. My internet intermittently goes out, every couple of minutes. I keep getting pop ups saying "Local Are Connection has limited to no connectivity" and/or "a network cable is unplugged".
View 5 Replies
View Related
Dec 31, 2012
I'm trying to setup a router in my moms house. She has DSL and when the box is connected directly to her computer everything works fine. However, if I connect the router her computer reads "Limited or No Connectivity". I can connect to the router wired and wirelessly with my laptop, phone, and even her streaming media box without any problems. I ran IP config and i'm not geting a default gateway address.
View 3 Replies
View Related
Jan 30, 2012
I have a laptop that I usually use physically connected to my router, but sometimes I use it wirelessly when I want to lie down in bed.After using it wirelessly yesterday for about an hour,I brought it back to where I normally connect it with an ethernet cable but not I can't access the internet even with the ethernet cable plugged in! And wireless doesn't work either,I have "Limited or no Connectivity" for my LAN Connection and Wireless. I cannot afford a new computer (and I also doubt I need a new one).
View 6 Replies
View Related
Mar 18, 2011
I am working on development of a Windows based application which connects to a PDA like device over USB & communicates with it using RNDIS protocol. The device has a static IP in the APIPA range (169.254.2.1). When it is connected to PC, Windows allocates a dynamic APIPA IP (169.254.x.x) to the RNDIS adapter. I have confirmed that there is proper connectivity with the device (I can ping it, can access a web server on the device etc.).But the problem is that after Windows allocates the dynamic IP, a 'limited or no network connectivity' message is displayed in system tray.
Since the device & software will go out in the market, display of this message (& exclamation mark on the network tray icon) is undesirable. I know that it can be suppressed by setting property of network adapter, but would prefer a solution that would not require end users to do any settings using APIPA addresses is essential as we would like to avoid conflicts with end users' LAN addresses.
View 5 Replies
View Related
Dec 20, 2011
This afternoon the computer crashed. It restarted normally, however will not connect to the internet. Upon start up, icon states it is connected but will not connect to the internet. When attmpting to Repair connection, Windows is then unable to fix the problem. All other devices work normally on the home network (Laptop, Xbox360).
I have also tried 3 different Restore points, but Windows states it is unable to restore to this point and to select another Restore point on each attempt.
I am running Windows XP SP3 on a Dell XPS
View 4 Replies
View Related
Jun 12, 2012
I found out my onboard ethernet port was fried, so i went out an bought a RTL8139D ethernet PCI adapter. I fitted the adapter and plugged my cable in. It said Limited or no connectivity. After hours and hours of googling I tried everything. I changed the protocols, created static Ip's went into cmd and reset winsock catalogs, release/renew etc. The cable I am using worked previously in my room and it still works. (I took a laptop up to my room and plugged in the cable and had internet connection). So... I took my PC downstairs and used a different cable. This successfully connected me to the internet. That Rules out that my new ethernet card is the problem. MY cable also allows others to connect to the internet. Windows 7 64X Ultimate edition.
View 1 Replies
View Related
Jul 26, 2011
I have gone through the previous post related to limited or no connectivity.But I am still not able to figure out the problem with wireless connection in my windows xp sp2 OS.
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:Documents and SettingsAnuj>cd ..
C:Documents and Settings>ipconfig/all
[code]....
View 4 Replies
View Related
Aug 31, 2011
i have built my PC from the ground up with what little budget i had, upon completion i started it up and installed my wireless adapter from linksis and i could not connect i went on my netbook (what i am on now) and checked my router and i didn't have any from of connection with my PC so i tried a wired connection and still no joy i have tried a different adapter a Belkin one i have even switched the router
View 1 Replies
View Related
Jan 31, 2013
I have tried renewing my ip address from the cmd prompt i have tried ipconfig/release, ipconfig/flushdns,ipconfig/renew and it didnt work my connection still keeps on going back to limited or no connectivity my DHCP is connected and i have default gateway ip i can get good connectivity if i reset the router by unplugging it but it still goes back?
View 19 Replies
View Related
Aug 2, 2012
I started having this stupid problem after i built my first computer, in my old computer it was all fine, am using an ethernet cable between my pc and laptop, it is crossed or whatever its called, when i plug it in it gievs me an error, limited connection or no connectivity which pisses me off, i have all the drivers installed everything is up to date.. sometimes it connects, but after 10 mins it disconnects again, and sometimes it works fine until i reboot my pc..
View 17 Replies
View Related
Dec 7, 2011
When I connect to the network, everything is fine for awhile, but then I get Limited Connectivity. It's fixed easily, I just disconnect and re-connect to the network, but I was wondering how I could fix this permanently. The amount of time I have before each time it goes Limited varies, could be 5 minutes to a few hours. And I know it's not the network but my laptop because other laptops connect and have no problems. I am on Windows 7 64-bit[CODE]
View 9 Replies
View Related
Jan 21, 2011
Fix limited or connectivity status of wireless connection
View 1 Replies
View Related
Aug 6, 2011
I have WIN XP installed on my DELL E6410 Latitude laptop. When I start my laptop, it acquires the internet connection fine, whether wireless or the wired connection.However on the wired connection, if I unplug the cable and replug it, it does not get the connection. It shows Limited connectivity or no connection. If I try to repair, it says , the IP address could not be renewed. Nothing works but restarting the laptop.Same is the case with wireless connection at home. The first time it catches the wireless fine. However if the system gets locked because of inactivity, and I unlock it, I am left with LIMITED CONNECTIVITY or NO CONNECTION message on the Wireless. I need to restart my comp because the repair or the disable and enable of WLAN does not facilitate.
View 19 Replies
View Related
Mar 29, 2011
My wireless show connected connection give me a 'limited or not connectivity' but a wired connection has no problem?
View 2 Replies
View Related
Dec 2, 2012
This computer is brand new Dell Inspiron 15R. The WIFI is dropping out repeatedly. I connect for ~10 minutes, but then the connection gets a yellow exclamation point for limited connectivity, and I can't reconnect until rebooting the router. I read the sticky but there wasn't a post for the 2230 network card.
The problem happened on windows 7 and now on windows 8. Rebooting the computer doesn't work. I tried the POWER SAVE trick and it didn't work. I tried the maximum roaming trick, and that didn't work either. The network card is the Centrino Wireless-N 2230 with the 15.5.6.48 drivers.
I can connect to the Verizon Wireless router or tether off my DROID X2 for about ten minutes, sometimes for longer, but either way, the connection is dropped, and I can't reconnect until rebooting the router.
View 3 Replies
View Related
Feb 23, 2008
I am experiencing - loosing network connectivity entirely (between the router and the cable modem) or loosing connection to some clients: 2 wireless laptops - one N and one G, and 4 wired connections. This requires a reboot of the router 2-3 times a day. Never experienced any of these problems with a Linksys WRT54G, a unit that this one replaced. Unless I can resolve it, the WRT54G is going back in, and WRT160N is going back.
View 9 Replies
View Related
Apr 1, 2011
he switch our internet and phone connection, our phone is now with vonage and internet to uBEE. SO ever since then our connection on the computer has been supper sloww. i am unable to play my games such as Crossfire this fps game. everytime i play it keeps telling me failed to connect to server. Then i sent a Support ticket and they told me to take this speed test.
View 5 Replies
View Related
Jan 8, 2013
I just switched ISP's and they provided me with a Ubee router. The computer plugged directly into works fine, great speed, no drops. A laptop connected via Wifi is the same, great speed, no drops.My Router is not simply 'dropping' connection, but instead, 'disabling' the internet to the devices and forcing me to reconnect in order to get approx. a few minutes of it again.I have a Desktop computer with a WGA600N Gaming adapter hooked up to it, and an iPod touch.Both worked perfectly with the old router, so I know it's the router for sure. The thing is, it's not just dropping and reconnecting..
It's connecting for a few minutes, and disconnecting permanently until I reconnect to the connection..For my iPod, it doesn't actually disconnect me, I just lose internet. It says I still have 3 bars of signal strength on my iPod, but I don't have internet. I must hit 'Forget this Network' and retype the password in order to get another 2-3 minutes out of the signal.As for my Desktop hooked up with the gaming adapter, when the internet 'runs out', I simply unplug it and plug it back in to 'renew' the internet.
View 2 Replies
View Related
Jul 23, 2012
I have been having some gripes with the above problem for the past few days, connecting several PCs in my office into a network. To cut a long story short, it's a bunch of XP SP2 and SP3 machines with only some of them having these issues. The network consists of two switches and one router with integrated modem and wireless. Internet access is established over that router/ ADSL modem.I have drawn out all the cabling and made all the connections myself, I don't doubt network related hardware one bit. Basically, I had the problem on two PCs, I tested connectivity on that cable with a laptop which didn't have any problems connecting to the network. All the cables are brand new, "straight" connectedC
View 14 Replies
View Related
Mar 17, 2011
i did this and the sign of unable to connect went away, restarted back to it, did it again and it goes away but still no connection. TCP/IP stack repair options for use with Windows XP with SP2.
View 8 Replies
View Related
Sep 3, 2011
my internet is not working on my PC (XP) however the wifi in my house is still on (i can use laptop with functioning internet). The internet status say's "limited or no connectivity" and shows a yellow triangle with an exclamation point in the middle.
View 19 Replies
View Related
Sep 9, 2011
I manage a small office network IP's are generated via a rooter. I need to add a new pc to the network and here is where the problem starts.I have a cable from a HUB in that office which has a splitter 1 way goes to a PC the other is empty. At first i tried connecting the other PC from that splitter but i get the Limited or no Connectivity message on both PCs. If i connect only one of them to the splitter the connection works fine.Now i tried with a HUB, made a Crossover cable from the splitter to the HUB in the WAN port, same deal both PCs get Limited ot no Connectivity. THe strange thing is that if i connect only one via the HUB the same thing happens.I am really out of ideas, my only option left is to connect the PC from the main HUB which means allot of cable posing.
View 3 Replies
View Related
Oct 3, 2011
When using an Ethernet cord, I have no problems connecting to the internet. Also, my iPhone and my Wii have no problems connecting (wirelessly). However, I can't get any laptops to connect to my wireless. I have tried three different laptops and get the same problem, that it can connect to the network but limited or no connectivity.
View 1 Replies
View Related
Aug 28, 2012
I have a spare computer I build. Its a FX-60 on some old asus 939 motherboard. I installed xp in it because I don't have any wireless network adapters that work with linux or Windows 7.I am using an old Linksys WUSB11 Ver 2.6. USB adapter.The computer does have connectivity if I plug in an ethernet cord from the router. Worked fine, fast, was able to install Sp3, etc.I can't get the wireless to work. I get excellent connection strength, but can't actually do anything with it.Since this is XP and I haven't messed around with XP network settings for years, I think I got a bit rusty and spoiled with Windows 7.
View 6 Replies
View Related
Apr 27, 2011
Newly purchased DSC-930L connected to DIR-625. Firmware is 1.0 for DCS-930L and A1-1.09 for DIR-625.Camera works fine when connected with cable. Wireless enabled, fixed IP address.Unplug cable and camera still works fine for a while: can access the view page and view picture that does change. F5 refreshes page no problems. After a while (about 5 minutes) web page no longer reachable by browser. Reconnect cable and works fine, unplug and repeat the cycle same thing happens.Also tried: unplug ethernet cable, unplug power cable, wait 10 seconds, connect power cable, try to browse to camera - cannot reach camera.
View 13 Replies
View Related
Oct 19, 2011
Limited OR No Connectivity.
View 1 Replies
View Related
Jul 19, 2011
used to use Ethernet connection on this pc for 2/3 years, i recently ran wireless for like 2months. every time i try and use Ethernet i get limited or no connectivity warning, I looked in my ipconfig, i notice theres no physical address or default gateway for my realtek rtl8139/810x family fast Ethernet.
View 4 Replies
View Related
Sep 9, 2011
I got the urge to play a Windows game, so I used my restore disks to install XP on my Acer Aspire One A150. Unfortunately, my wireless card does not work anymore (?). I am dual-booting with Ubuntu 10.10 at the moment and my wireless card works there with no problem.I get a Limited or No Connectivity error every time.I'm connected to a router, which I have reset and works okay in Linux. I am connected currently using a USB D-Link N-Adapter, however, despite being "N" is considerably slower and inconvenient.
[code]...
View 13 Replies
View Related
Apr 19, 2011
I just installed a new NIC after troubleshooting old NIC and I am still receiving limited or no connectivity error. I checked router, cable modem & cable; all work fine.
View 13 Replies
View Related
