We installed a DIR-615 Vers. E1 FV. 5.00NA and since then i-Pods and i-Pads keep dropping wi-fi connections. All wireless PC's and printers are working fine. We have configured the wireless as:Mixed 802.11 n,g and b. Auto channel csan enabled, using channel 6. Wireless security is WPA-Personnal. WPA is configured as Auto, TKIP and AES with a pre-shared key.
View 5 RepliesI work at a small private school that is going to implement about 20 ipads for classes. Students bring their ipods and iphones and are connecting to the existing unsecured wireless access points and are taking up the remaining IP addresses in the DHCP scope. I am running out of IP addresses and was wondering if I could set up a VLAN using the Cisco WRVS4400N for all of these wireless devices the students will be using. I plan to pull out all unsecured wireless AP's and replace with what ever solution we come up with. I will need about 6 access points/routers to cover the entire school. There is not a lot of money for technology and the ipods were donated. I have never set up a VLAN before. Is there an inexpensive way to allow the students with their personal ipads/ipods and the 20 ipads owned by the school to connect to a VLAN to keep from using up our DHCP IP addresses from the server.
View 1 Replies View RelatedThis router has to be rebooted every 12-24hrs to re-establish the internet connection.
View 14 Replies View RelatedI have just purchased a DCS 2121 (I assume that it is a similar model to the DCS 920 in US).I have this setup:
- Connected the DCS 2121 wireless to my Belkin Router with a fixed IP address. Firmware version 1.4 is installed on the camera.
- I have a Synology 209 NAS server with surveillance station that I have connected to the Camera.
I all works fine for 5 minutes to a couple of hours at which point the DCS 2121 loose connection to the Router and does not try to reconnect. If I turn the Cam on and off it will reconnect - and then loose connection again af a short time.This is totally frustrating since the purpose of the Cam is to work as a surveillance cam - it kinda loose its value by not being connected...
Bought a Dir-600 from challenger, used it for 3 months and started expericing the common problems of loosing internet connection highlighted by many users here and in other forums. Would always have to do a modem / router power cycle to get it going again.Slightly after 3 months... the thing went dead. Can power up but no response. Cannot detect the modem.Got a one-for-one exchange at Funan. Used the 2nd one for less than 2 months. It just went dead on me! Same problem...
View 3 Replies View RelatedNot sure where the best place to drop this question. It is a DIR-601 router. I have it configured in the virtual servers list as; internal system ip, public port/private port both 23, protocal tcp with inbound filter, allow all and schedule set to always. I have a second system with a different public port. I can connect to either one but after a short amount of idle time it appears to just drop the connection.
View 4 Replies View RelatedI have a TrendNet TEW-639GR, my ISP is Saddle Mountain Wireless. [code]
View 3 Replies View RelatedMy nephew's XBox (he's an on line gamer, and quite a serious one for that matter...) seems to boot him off line when someone uses the phone or goes on line on another computer. The house is quite far from the exchange so the average down speed is only 1.75-2 Mbps. This connection is through a BT Infinity R/S/F and I wanted to know if we could just add another R/S/F device and subnet the games console into it's own DMZ with full bandwidth access and then the normal broadband & phone on a different subnet also with full bandwidth access?
View 3 Replies View RelatedOk, so if i open Utorrent and let it download for 10 minutes i loose my internet connection. I usually will disconnect my cat5 cable and plug it back in and it doesn't work so i would open up the CMD line and try to reset the network connection but it doesn't respond so the only way i can reset it is to restart the the computerI've tried reinstalling Utorrent but i still keep loosing my connection, yet all the while I am able to run netflix on my PS3 so my internet connection isn't going down.
View 1 Replies View Relatedmy linksys e3000 router loses connection quite often. E.G. we lost power last night and i tried resetting the router but it didnt work so I had to uninstall and then reinstall the router. A few other times it would lose connection for no apparent reason.
View 8 Replies View Relatedim loosing connection every few minutes , tried ipconfig /release , ipconfig /renew and im getting this error every time : An error occurred while renewing interface Local Area Connection : unable to contact your DHCP server. Request has timed out. After typing ipconfig /all DHCP address is 255.255.255.255 and this IP 192.168.100.10. Tried other things like flushdns / netsh commands and nothing want to work. My connection works only after i restart my modem. Modem type Ubee 3236. The modem is new got it 4 days ago. And also why i cant access the modem configuration page by typing my default gateway in browser ?
View 4 Replies View RelatedI have recently changed my router from Netgear to TalkTalk because of an intermittent signal, no problem with my desktop ethernet or laptop wireless or tablet but I keep loosing connection with my WII internet connection for Netflix.
View 10 Replies View RelatedWe are in a hotel that allows us to use their router with a Hawking 300N expander. We seem to lose connection each time their router gets a new IP address. The router seems to lose connection frequently. Is there a setting in the expander that will allow the expander to "follow" the DHCP address of the router without having to take it down and go thru the setup each time.
View 2 Replies View RelatedI have several computers and printers connected to a WRT120N router which is connected to 10mpbs DSL. The computers are all running WIN7 and are hardwired to the router. On the one PC, it keeps losing network connection. I've tried upgrading the router's firmware, reset, etc. to no avail.
I think it may be related to the same IP address being assigned to multiple machines connected to the router. Is there a way to set specific IP addresses to each item connected to the router to see?
My IP provider has upgraded my broadband speed in early Jan. They require ADSL2. It seems to coincide with this date that I keep loosing my internet connection on a regular basis, say every 2 days or so, but not consistent. The cure is to unplug the linksys WAG200G ADSL home gateway. Plug it in again and all is well, until the next time. On the box it says the until is ADSL2/2+ compliant.
View 2 Replies View RelatedF9K1103 v1 (01C) keeps loosing internet connection, the router is wired to a time warner modem and wireless is not enabled.
View 2 Replies View RelatedI've recently upgraded from a WAG54GS to the WAG320N. It seems to work OK for a period then looses the connetion to the Internet - DSL light on but not the Internet light. Normally I need to re-set the router to re-connect (either through the back switch or through the setup page)
This is my DSL information from [URL] whilst connected OK
--- System Information ---Vendor: LinksysModelName: WAG320NFirmware Version: 1.00.08 , 2009-08-27T19:37:13Boot Version: 1.06Hardware Version: 0.01--- DSL Information ---DSL Driver Version: AnnexA version - A2pB023k.d21dDSL VPI/VCI: 0/38DSL Status: ShowtimeDSL Mode: ADSL2+DSL Channel: DSL Upstream Rate: 1023 KbpsDSL Downstream Rate: 18723 Kbps Down up DSL Noise Margin: 9.1 dB 6.7 dBDSL Attenuation: 22.5 dB 12.0 dBDSL Transmit Power: 19.0 dBm 12.5 dBm--- Wireless Information ---Wireless Driver Version: 5.10.85.0.cpe4.402.4Wireless Status: EnabledWireless Wide Channel: 9Wireless Standard Channel: 11- 2.462GHZWireless SSID: irae_2--- Dynamic Information ---LAN Mac Address: 00:22:6B:F5:6F:A7WAN Mac Address: 00:22:6B:F5:6F:A9Wireless Mac Address: 00:22:6B:F5:6F:A8---
When the modem looses connection to the Internet; the DSL Noise Margin drops way down to 0.0 or 0.5.
I upgrade firmware from 1.0.3.5 to 1.0.4.17 and from this time I can't connect to any site time from to time. I have simple DHCP WAN connection between my provider and the router, my computer connects to router by wire (only Cisco SG 100D-08 stands between them). When I can't access sites I can access my router and the router needs much more time to answer to me via http. I don't use any vlans or internet access to my computer or router.
View 2 Replies View RelatedI purchased a brand new Acer Aspire 5250-BZ669 that included Windows 7 just two days ago. Everything is working fine on it except for it randomly looses connection to the internet. I have an established network that I have been using for years. The signal strength is always 5 bars and excellent. I also have a compaq connected to the same network, and it never looses connection. However my Acer will randomly drop connection. I have no idea why. Sometimes it will connect again in minutes or sometimes hours. I am using a Linksys G Wireless Router(Model # WRT54G2), Atheros AR5B125 Wireless Network Driver, and a Atheros AR8152 Controller. I have enabled and disabled in addition to uninstalling and installing the driver and controller many times. I have also moved the router and adapter all over the house. I have downloaded the newest versions of every driver from the Acer website. I have googled for hours looking for the answer to no avail. I run the troubleshoot and the answer it gives me is to make sure all the connections to the router is secure, which it is or else my other laptop wouldn't work.
View 19 Replies View RelatedIm loosing connection every few minutes , tried ipconfig /release , ipconfig /renew and im getting this error every time : An error occurred while renewing interface Local Area Connection : unable to contact your DHCP server. Request has timed out. After typing ipconfig /all DHCP address is 255.255.255.255 and this IP 192.168.100.10. Tried other things like flushdns / netsh commands and nothing want to work. My connection works only after i restart my modem. Modem type Ubee 3236.
View 14 Replies View RelatedMy Cisco X3000 keeps loosing the internet connection after 1 day and will only reconnect if the device is rebooted. Pressing the Internet connect button in the Status page does nothing.Even when the Internet connection is lost, the wireless network is working 100% and all the devices on the network stays connected and are accessible.The router has been updated to the latest Firmware available from Cisco v1.0.03 build 001 Jun 11,2012
View 9 Replies View RelatedI had the WAP610N for a few months with no issues. As always, I have a custom SSID and password, using WPA2. All of a sudden, none of my mobile units (at least 5) are unable to connect via the WAP610N. However, I can connect to a Netgear N750 w/o any issues. When I reboot the WAP610N, it resolves the issue for a few minutes, but then behaves the same as before. I know its not my network because, I am able to connect via wired and wireless via the Netgear. I verified via the web interface that none of the settings/configurations have changed - but still nothing. Latest firmware has been applied. Note sure If I should perform a factory reset or re-apply the firmware.
View 2 Replies View RelatedThe router keeps loosing connection to the internet. I can still log into the router locally but cant connect out or in from the internet. Which is a big problem as i use this device remotely. I have tried different firmware (.9, .19, .27) the .19 seems to be the most stable but i am still having problems. The only way to rectify it is to reboot the router. Is there a fix for this or a way to schedule a reboot on the router.
View 2 Replies View RelatedI have two WAP321s in my office. The network they are on is a single VLAN (172.16.10.x). Both WAPs are setup with the same SSID, and I have setup Single Point Setup.
I am having a problem that was happening before I setup Single Point Setup, and it is still happening. Basically wireless will be up and running fine for part of the day. Then people throughout the office will begin to lose their connections to the DHCP server. They still retain the connection to the WAP, but can no longer access the network.
The only way I have been able to fix this issue is to reboot the WAP. As soon as it reboots the connections come back. At first I thought it was due to the number of connections (which is why we now have 2 WAPs), however we only have about 20-25 conncurrent connections.
I put in the second WAP to try to balance out the load but this does not seem to be working. Is there a setting I need to change on the WAPs to balance out the load?
I have a Belkin N600 model # F9K1102v1 i am loosing connection on all of the components connected to it wired or wireless. They all loose connection at the same time. I also noticed the clock in the router does not set to the correct time it is reading 1970 for the year and never changes.
View 1 Replies View Relatedhave a HP 6500a All In One Printer in the network with a BERSR41 V3 router. I am using a Imac with this sytem for printing and scanning. For some reason I keep loosing the printer when I try to scan? I have it set to a static IP, and can not ping it, but can access the printer throught the network with the HP Utility. Am I missing something in setup on the router that causes it to keep loosing connection?
View 2 Replies View RelatedI Updated the 5508 from 7.0.230 to 7.4.100 and made it a cluster.Sinse the Update the handscanners loose the connection to the AS400 Application.Where to start troubleshooting?I did a debug client, I see the client is roaming but I can not say if there is a relation between roaming and loosing connection to the application.
View 19 Replies View Relatedsince a couple of days I've a strange behavior in my Spanning-Tree Topology.Every time I plug in a new Switch ( e.g. WS-2960S ) a topology change on my root bridge occurs and all client losing connection to the default gateway.The root bridge is also the default gateway.
Nov 28 11:14:12.865: STP: VLAN0001 Topology Change rcvd on Gi4/48
VLAN0001 is executing the ieee compatible Spanning Tree protocol
Bridge Identifier has priority 0, sysid 1, address 0019.aa37.e040
Configured hello time 2, max age 20, forward delay 15
We are the root of the spanning tree
[code]....
we updated our NAC appliances from 4.8.1 to 4.9 and have noticed that web authentication is no longer woking on Apple IOS devices. We had setup a user page for the MAC_ALL OS and iphones etc. were able to authenticate using thier browser ok. Now (after the upgrade) after they authenticate they receive the below warning.
There doens't seem to be any other config changes we can make for the IOS device.
Ever since I started using iPads at the house I have had to reboot the router about once a week because the download speeds drops by approximately 90%. As soon as the reboot completes all is right with the world for about another week. During the course of the week, but not all at once, we will have 4 iPads, 3 iPhones, 2 laptops and one desktop(wired), a Verizon signal booster and house guests. I have updated the firmware.
View 1 Replies View RelatedAll, I am the wireless administrator for a rather large school district in Oregon, and we are seeing numerous issues with iPad's connecting and staying connected to our lightweight AP's in an HREAP configuration. Our iPad carts have about 20 iPads a piece and an AIR-LAP1142 supporting them. We have no issues with getting non-Apple products to connect and stay connected, but for some reason the iPads are creating a major issue. We currently run 8 4400 WISM blades via two 6509's, running code 7.0.116.0.Our AP's are running 7.0.116.0 as their primary software and their IOS is 12.4(23c)JA2.
View 12 Replies View RelatedI have a small home LAN of four hard-wired PCs and two iPads and two notebooks which are connected by wireless. At the heart of it all is a Linksys X3000 wireless router. Any of the four PCs that are hard wired to the X3000 have no problems talking to each other but none of the wireless-attached iPads or notebooks are able to see any other machine on the network. All machines are able to access the Internet.
View 9 Replies View RelatedCisco Air 1131 AP. Having problems with Apple products. Even tried no security.
View 2 Replies View Related