Cisco WAN :: MLS QoS Map Command Missing On 2801
Oct 31, 2012
I am trying to run the following commands on a 2801 router, but the commands are missing:
mls qos
mls qos map cos-dscp 0 8 16 40 32 46 48 56
The only QoS command i have in global config is (no MLS qos) :
REMOTE-ROUTER1(config)#qos ?
restore-show-output Restore old show output
shape-timer Set the HQF shape timer interval
The router is running IOS:
System image file is "flash:c2801-ipbasek9-mz.151-4.M5.bin"
Am i just running the incorrect IOS or am i missing somehting, i need to change the QoS Map for my Nortel VoIP. The VoIP phones connect to a 3750 PoE which used to conenct to a 2651XM to route VoIP and data traffic over the same copper pairs (WAN link to hub site) hence the need for a Service policy but being Nortel phones, require changing the cos-dscp map. the 2801 is going to replace the 2651XM using a new HWIC.
View 4 Replies
ADVERTISEMENT
Nov 17, 2011
We have a cisco 2801 router in class which has a disabled password recovery. We tried almost everything, we cannot get into ROMmon and the break sequence doesn't work in any program (hyper terminal, putty, teraterm pro).
Here is the log from hyperterminal:
System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)Technical Support: [URL].Copyright (c) 2004 by cisco Systems, Inc.PLD version 0x10GIO ASIC version 0x127c2801 processor with 131072 Kbytes of main memoryMain memory is configured to 64 bit mode with parity disabledReadonly ROMMON initializedPASSWORD RECOVERY FUNCTIONALITY IS DISABLEDprogram load complete, entry point: 0x8000f000, size: 0xc100Initializing ATA monitor library.......program load complete, entry point: 0x8000f000, size: 0xc100Initializing ATA monitor library.......program load complete, entry point: 0x8000f000, size: 0xd49718Self decompressing the image :
[code].....
View 5 Replies
View Related
Apr 6, 2012
I have a stack of 3750's running IOS 12.2(25). "IP forward-protocal" command is configured, but the IP helper command is just not an option to put on an interface. Any have any idea of why that could be?
View 2 Replies
View Related
Mar 11, 2013
My 3550 is always 2 characters short on the command line. So my global configuration mode will look like this:Switch3550(config Say I wanted to enabled ftp, it would look like:Switch3550(config)# ftp enab.
View 2 Replies
View Related
Sep 17, 2011
I've finally got my 3560 switch IPv6 capable (IP Services IOS), but I've stumbled upon something strange: I can configure a tunnel interface, but I can't put the tunnel in ipv6ip mode. The command is missing. I can choose GRE, IP in IP, and a bunch of other things, but no ipv6ip. I'm a bit desperate here and probably I am going to have to live with it, but just in case? I need the IPv6 tunnel for an uplink to a tunnel broker which only supports this type of tunnel, and I'm surprised this is missing.
View 4 Replies
View Related
Oct 9, 2012
My customer has upgrade his 4506 from 6L-E to 7L-E 10GE.Ever since then if he run the command show dot1x interface gigabitEthernet x/x details some information are not been displayed (below are missing information)Is this intensional or do I need to kick this to TAC?
View 1 Replies
View Related
Jul 19, 2012
On the Cisco forums, an example is shown for how to configure BVI and bridge-groups on an ASR1004 but the same command (bridge-group) is not available under the interface on our ASR routers. We are running version of code: asr1000rp1-advipservicesk9.03.06.00.S.152-2.S.bin
View 1 Replies
View Related
Jun 16, 2012
I am trying to chang IP configuraton for my Cisco 1140 AP, but in CLI I dont have a "config" command (i used en before to enable administrative mode)
Bellow are the commands I can see:
AP7081.0506.d54a#?
Exec commands:
cd Change current directory
[Code].....
View 5 Replies
View Related
Jun 14, 2011
I have two Aironet 1231Gs, that are both running the same version of fimware: Version 12.3(8)JEE
From the gui, I try and change the channel on the main radio interface--It works from one, and I get just a blank page on the other. When I try and change it via the cli, I use the "channel" command in conf int mode, and it works one the one, but the other one, the "channel" command doesnt exist.
View 1 Replies
View Related
Feb 21, 2012
I have a switch WS-C3560G-48TS.The version of IOS is:
WS-C3560G-48TS 12.2(58)SE2 C3560-IPSERVICESK9-M
The command "track number rtr" is missing. There are just three options there:
#track 10 ?
interface Select an interface to track
ip IP protocol
list Group objects in a list
Why is that so and where is rtr?I have the same switch with the following ios version:
WS-C3560G-24TS 12.2(50)SE1 C3560-IPSERVICESK9-M
rtr is present in there.
View 2 Replies
View Related
Apr 19, 2011
I have been looking around and I can not find the " crypto isakmp policy " command on this Cisco Router 1941. I just wanted to setup a regular IPSEC Lan to Lan tunnel and surprise, the command is not there. Do I have the wrong IOS? I thought that a K9 image would do the trick. [code]
View 2 Replies
View Related
May 9, 2012
I need to create a Cisco VPN Client connection: I am following the cisco vpn client link and I don't have the command crypto isakmep client configuration group XXXXX
[URL]
This is what I get: crypto isakmp client configuration ? address-pool Set network address for client
This is my show version, if there is an IOS that will work:
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IK9S-M), Version 12.2(17a), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2003 by cisco Systems, Inc.
[Code].....
View 1 Replies
View Related
Feb 10, 2013
I recently rebuilt the configuration of our Cat6500 multilayer device for use as a user stack. The device is funtioning as it should be, but I am unable to set SSH using the 'crypto key generate rsa' command. The crytop command isn't avaiable at all, which suggests a firmware issue.
I have configured a hostname and Ip domain-name and the image is the only one available.
The show version output is listed below.
show verCisco Internetwork Operating System SoftwareIOS (tm) s72033_rp Software (s72033_rp-IPSERVICES_WAN-VM), Version 12.2(18)SXF12, RELEASE SOFTWARE (fc2)Technical Support: [URL] Copyright (c) 1986-2007
[Code].....
View 2 Replies
View Related
Feb 22, 2013
I came across an interesting issue and thought I would see if anyone else has encountered it before contacting TAC.I have two Cisco Catalyst WS-4510R-E switches with a single Supervisor V module in each chassis. Both Sup cards are now running 12.2(54) SG1; ipbasek9 firmware; yes, I plan to move both switches to 15 code but that's another story. Anyways, prior to the upgrade the one switch was running 12.2 (33) code; I suspect the code was never upgraded; running ipbase non - K9 code. The other switch was running 12.2(44) with K9 prior to upgrade to 12.2(54).
View 2 Replies
View Related
Apr 23, 2012
I have two Cisco Catalyst WS-4510R-E switches with a single Supervisor V module in each chassis. Both Sup cards are now running 12.2(54) SG1; ipbasek9 firmware; yes, I plan to move both switches to 15 code but that's another story. Anyways, prior to the upgrade the one switch was running 12.2 (33) code; I suspect the code was never upgraded; running ipbase non - K9 code. The other switch was running 12.2(44) with K9 prior to upgrade to 12.2(54). With the background set, one switch reports the following:SwitchA (config)#r?radius-server redundancy regexp represourc rmon route-map router.
View 4 Replies
View Related
Feb 5, 2013
I have a Cisco 2801 with dual ADSL WAN connections, PATing to a network hanging on the fa0/1 interface. From the server connected to the router (hanging off of the fa0/1) interface, I can ping any address and there are no issues. But from inside the Cisco CLI, pinging certain addresses causes erratic behavior. [code]
View 5 Replies
View Related
Nov 9, 2011
I have a 2801 router. The Fa0/0 int shows up/down. I have plugged it into diffrent cisco and non cisco switches and even a cross over cable to my laptop. I cant seem to get the protocol up. I have changed the speed to 100 and duplex to full to try to get it up that way and nothing. [code]
View 7 Replies
View Related
Dec 23, 2011
I have a 2801 with dual ISP connections, and I have configured route-maps to direct voice traffic over ISP1 (working just fine), and I'm attempting send all other traffic over ISP2 (traffic is load-balancing instead). The connection to ISP2 is DHCP, and I have configured a route-map to route this traffic using the 'ip next-hop dynamic dhcp' command, but when I look at the route-map, it states the following: ip next-hop dynamic dhcp - current value is UNKNOWN..Is there something that I need to enable in order to see the next-hop, and properly send traffic over the ISP2 connection? [code]
View 9 Replies
View Related
May 3, 2012
I have a Router 2801 What conf should i make to access the webserver from the same LAN.
!
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.1.1 192.168.1.63
[Code].......
View 6 Replies
View Related
Jul 23, 2007
I looked but could not find any information on what's the use of the USB interface on my 2801 router. I saw something about Cisco USB memory module and eToken by Aladdin. Is this interface restricted to Cisco and Aladdin only?
View 17 Replies
View Related
Oct 14, 2012
I have a Cisco 2801 with flash: c2801-advipservicesk9-mz.124-16.bin where I use to doing VPN IPSEC.My problem is where I do a connection with a client, if my VPN dont have a traffic, the tunnel are closed. If a receive or send any traffic, the tunnel get up again.If don't have traffic, this tunnel is closed and after is opened other tunnel where is changed the conn-id to 999 for example.This comportament is normal? Exist a form that my tunnel never close? I enabled the parameters below: [code] But the tunnel continues closing if a don't have traffic.
View 5 Replies
View Related
Mar 21, 2012
We are setting up a new VPN from an ASA to a cisco 2801 router (behind a third parties checkpoint firewall). We seem to be almost there with the setup but the tunnel is not working correctly. I have included a debug from the 2801 router and its config and a diagram of the setup. [code]
View 2 Replies
View Related
Aug 4, 2011
I have a Cisco RV110W small business router setup at my home. It has one of those HTML GUI interfaces, check the boxes, etc.., to get things working. Basically, your typical home router with VPN. I have enabled the VPN, it's PPTP, added the password, and now it's automagically configured! I can successfully VPN to my home with a Windows7 client. Here's my problem, I now need to VPN into my home router with a 2801. Is this possible? Everything I found on the subject has only been to setup a Cisco IOS router as a VPN server or tunneling to another IOS router. No examples using an IOS based router as the client.
View 3 Replies
View Related
May 29, 2012
We have one Router Cisco 2801 at the customer site and facing issue of having very High CPU coming to 99%.CPU utilization for five seconds: 99%/28%; one minute: 99%; five minutes: 98%
View 2 Replies
View Related
Jun 23, 2011
We have a 2801 rotuer in place that hooks up to a metro ethernet link that's obviously dropped off to us via ethernet. Anyway, the throughput granted to us is 20MB, but for some reason I can't get it to go anything above 11MB at the most. I've spent a day going through documentation trying to find the fastest speed the 2801 supports and I can't find my answer. I've seen that the high speed wan cards in this router support up to 45MB, but I'm not using a WAN card, only one of the two built in 10/100 ports.
what the maximum throughput speed is on a 2801?
View 7 Replies
View Related
Mar 26, 2011
I have a FWSM in my 6509, this firewall is managing three VLANs, one of which holds a file server. As you all know, FWSM do not support VPN like the ASAs and PIXs do. I have been trying to add remote access to this file server LAN all week. The only VPN device i have is a 2801 router.
first layout: VPN router behind FWSMstatic translation from FWSM LAN (private) to VPN WAN (public)default route was facing back at FWSMip address pool was to be NAT'd on the interface facing the FWSM the idea was that my VPN address pool would be NAT'd back to the FWSM on it's VLAN. since the FWSM was managing this VLAN and recognized the source IP of the translated address pool, i would have access to my precious file server.
second layout: VPN router fa 0/1 on a /30 with 6509 (public)VPN router fa 0/0 still on the same LAN as FWSM (private)address pool for VPN once again NAT'd to fa 0/0default route pointed to fa 0/1static route of FWSM LAN pointed to fa 0/0 this idea was to have more of a 'inside' and 'outside' interface on the VPN router. this too did not work, having used every trick in the book, i could still not ping anything on the FWSM LAN while VPN'd in the network (aside from the LAN interface on my router)
trace route was showing that the all routes were headed out fa 0/1 (default route) and all to my FWSM died. i really don't think my address pool is being NAT'd, though my route map statement applied to the NAT policy is permitting my VPN address pool.
I am new to VPN technology, one of those things that happened to land on my lap. how this layout could work? there are no good VPN Remote access walkthroughs for a situation like this (2801 allowing access to a FWSM controlled LAN)
View 2 Replies
View Related
Apr 23, 2011
i have configured remote access vpn on my 2801 router's gio0/0 int ip x.x.x.1. i connected my laptop through vpn client from internet. i connected successfully and my vpn router gives me the assigned ip block y.y.y.1. from my laptop i can ping the other int gio/1 ip z.z.z.1 but i cant ping the ip z.z.z.2 of my core sw which is connected on router's int gi0/1.
View 14 Replies
View Related
Jul 31, 2011
The application here is a wind power project, built in two phases, without any effort to coordinate or integrate the two sites during the design phase. All operations activities for both phases are performed by one staff out of a common location. This is a rural area and Internet connectivity is mission critical due to contractual obligation with Electrical Utilities.
The client has a need to reconfigure a network which has grown over time in a layer by layer approach, whereas at every point in time that an additional T-1 or other changes occurred to address a specific need, no thought was ever put into integrating the entire site as a whole. It is at best a dysfunctional solution which somewhat accomplishes thier needs, and at worst, a kludgy, grossly security compromised, and difficult to use infrastructure. There is every kind of equipment one can imagine, each installed by some entity providing needed services on the site, but forced to make uninformed decisions because the client really has no IT department to coordinate with. Over time, every vendor just provided their own switch, router, or maybe figured out how to reconfigure another existing device to also provide the routing or access needed, To say the least, it's a mess.
The client requests a solution which provides a means to accomodate 6 internet connections (4 T-1 lines, and 2 satellite) in a manner which aggregates available bandwith and provides redundancy. The T-1 lines will be the main internet access, with the satellite connections only used if available bandwidth falls below some threshold, say 3Mb. There are many internal networks which need to be routed to and between, in total, about 20 subnets. There are 2 SCADA (Control) networks which have a mandatory requirement of 1Mb each, a VoIP system which does not use any internet connetivity as there are 6 POTS lines dedicated to it, an internal office LAN and a turbine manufacturers site LAN.
The T-1 lines, at 1.5Mb x 4 = 6Mb.
The 2 SCADA networks require a guaranteed 1Mb each, the remaining 4Mb is to be allocated between the office LAN and the turbine manufacturer site LAN. The satellite connection are only to be active in the event bandwidth falls below 3Mb.
There are 2 Cisco 2801 routers on site which could be reutilized if appropriate. Each T-1 has it's own Adtran CSU with Ethernet out. All T-1 lines are /29 IP Blocks. 2 of the T-1 lines are adjacent IP Blocks, for what its worth.
Everything here is open to reconfiguration. The client wants this finally integrated correctly with the ability to address emerging Electrical Utility cybersecurity requirements in the immediate future.
An ideal solution would be fully redundant to eliminate the single point of failure at the edge router. As to whether there needs to be separate edge and interior routers, I just don't know that. I would guess everything could be done with just a pair of redundant routers at the edge, but perhaps it is better to do the interior routing between subnets on a different router(s).
Again, the goal is a well integrated, redundant, and secure solution. My part is mostly complete, with the OSP part of the network finally at 100% after 5 years of stupid and careless misconfigurations and bad fiber splicing (by others).
I'm absolutely covered up in business at Layer 1 & 2 on these sites, as the physical plant and associated network elements are typically very poorly designed, specified, and implemented. The complexity of this job leads me to seek outside advice and ultimately a more qualified Cisco professional than me. I'm experienced enough with Cisco to know when I'm in over my head. I know a diagram would be nice, but at this point I've only got a very detailed diagram which reveals too much site identity information to make public. I'll wait to see a few comments and in the meantime work on removing site identity info so I can post a good diagram for everyone to see.
View 1 Replies
View Related
Dec 19, 2012
Someone told me the commands, but I can't remember them. Have a router (2801) at the end of a highly utilized T1 link/router. How do I protect it so my SSH and/or Telnet sessions will get serviced if the router is real busy.
View 9 Replies
View Related
Apr 20, 2012
1- Cisco Router
Eth0/0 : Ip address 192.168.1.1 /24 == connected my laptop of 192.168.1.2
/1: Ip address : 192.168.2.1 /24 = connected cisco swith
2 - Cisco Switch
VLAN 2 Name : Sales : ip address 192.168.3. 1 = connected computer 192.168.3.2
VLAN 3 Name : Marketing : ip addres 192.168.4.1 = connected computer 192.168.4.2
So I want my laptop that connected the router Eth0/0 Interface should access both VLAN 2 and VLAN 3 computers
View 4 Replies
View Related
Oct 3, 2011
I've been looking and I can really find much info about this, I got a 1841 and 2801 router with ADSL WIC cards and both are synching really low compared to my cheap home router
This leads me to believe I need a firmware update so I got the adsl_alc_20190.bin and loaded it into flash and reloaded my router but its still saying my firmware is using an embedded one.
sh flash:-#- --length-- -----date/time------ path1 1000636 Oct 4 2011 05:59:54 +00:00 adsl_alc_20190.bin
sh dsl interface atm0/1/0ATM0/1/0Alcatel 20166/20174 chipset information ATU-R
[Code].....
View 3 Replies
View Related
Dec 6, 2010
I have a nat and vpn setup on my Cisco 2801 router.Everything is working as expected except the NAT. I have a single static nat translation but it only works for inbound and not outbound. Going outbound, it uses the default overload nat address of the outside interface. [code] I want to add another mailserver. But I fear if one mailserver were to get black-listed, they would both be reporting there ip address as the same address (the one on the ethernet interface) which would blacklist both mail servers.Again, inbound nat works ok, but outbound is just using the IP of the ethernet0/0 address.
View 2 Replies
View Related
Dec 14, 2011
I have a cisco 2801 router, My ISP in which i receive my bandwidth from has assigned me a ip address/gateway etc for my FA0/0 from our Telco switch. I need to figure out how to bridge through the public ip scheme they are issuing me through FA0/1 (setting up a transparent bridge) so in example if i was givin 192.168.1.189 on a /30 network for my router (assigned to FA0/0) how to i set it up to bridge through the publics?
View 9 Replies
View Related
