Cisco :: No Service Password Recovery Command On 2801 Router?
Nov 17, 2011
We have a cisco 2801 router in class which has a disabled password recovery. We tried almost everything, we cannot get into ROMmon and the break sequence doesn't work in any program (hyper terminal, putty, teraterm pro).
Here is the log from hyperterminal:
System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)Technical Support: [URL].Copyright (c) 2004 by cisco Systems, Inc.PLD version 0x10GIO ASIC version 0x127c2801 processor with 131072 Kbytes of main memoryMain memory is configured to 64 bit mode with parity disabledReadonly ROMMON initializedPASSWORD RECOVERY FUNCTIONALITY IS DISABLEDprogram load complete, entry point: 0x8000f000, size: 0xc100Initializing ATA monitor library.......program load complete, entry point: 0x8000f000, size: 0xc100Initializing ATA monitor library.......program load complete, entry point: 0x8000f000, size: 0xd49718Self decompressing the image :
[code].....
View 5 Replies
ADVERTISEMENT
May 1, 2012
i need to recover a router Cisco 2801. I lost the password and the "no service password-recovery" is configured. I have done many attempts with the procedure in this link :URL
View 9 Replies
View Related
Oct 5, 2011
I have a major problem with our core 2801 router. In summary it appears that a staff member disabled password recovery, deleted the IOS and rebooted. Net result is no Rommon and no IOS on the flash. I've read that the Conf-Reg will be reset if I remove the NVRAM but I cannot identify it on the board. If I can get to Rommon I can recover. Currently I don't have Flash reader to restore to flash.
View 2 Replies
View Related
Sep 26, 2011
I was just configured a 3800 router with this command. I cannot get to the ROMMON mode anymore. Cisco says you should press Break key within 5 seconds after the image decompresses during the boot. But mine is ignoring it and going to load running config directly.
View 7 Replies
View Related
Jan 1, 2010
I purchased a Cisco 851 router from ebay a few weeks ago that has the "no service password-recovery" option enabled. I've tried every "break" option i could find, and this thing does not seem to let me get in. I asked the seller for the password, and they refused (though i cant even get to a prompt to enter a password) or ROMMON. The unit comes up and reports its trying to connect to "Translating "stipp.srv.hcvlny.cv.net"...domain server" once it comes up, and thats it. [code]
View 34 Replies
View Related
Dec 27, 2011
I have an ACE10-6500-K9 (Application Control Engine service module for Catalyst 6500) but I can't access it because I lost the admin password.I would like to know how to perform a Password Recovery Procedure on this device.Is it similar to the password recovery procedure on an ACE 4700 appliance?
View 2 Replies
View Related
Feb 9, 2012
I enabled the "no service password-recovery" command on my C2960 switch. All seems to work as discribed. Only issue I have is --- which show command is used to reveal if the password-recovery feature is enabled of disabled as the command doesn't show up in the running config after you enable it ?
NOTE: The command does show up in the C2960 switch in config t mode (unlike the IOS router 2800 series), but doesn't show up in the running-config after you enable or disable it.
On the 2800 series routers (latest IOS) in config t mode the command does not show up but if you type "no service passowrd-recovery" the command function correctly and it does list it in the running configuration.
View 1 Replies
View Related
Aug 22, 2011
Recently I have bought a 2821 router from an auction. The router did have some configuration and password on it. I tried to break into it by restating it and pressing control and pause break signal. Old cisco method. Now when I try this method on my 2821. It does say that password recovery is disabled on the router. After this message router proceed with normal boot process. How to break the password ? Even if I loose the configuration.
View 4 Replies
View Related
Apr 7, 2012
i just wanna know if it's possible to perform a router password recovery using the reload command and then issue the break sequence instead of doing an off/on on the power switch. i often find in the docs to use the latter.also, is there a way to retain the startup-config on a router when we re-enable the password recovery functionality (no service password-recovery). i've just tried this on one of our 877 and when i hit the break sequence, it went back to factory default setting.
View 7 Replies
View Related
May 20, 2010
I understand that the password has to be changed the first time we login to Cisco 3945 router but i failed to do that and its not allowing me to connect using default username/password.
View 7 Replies
View Related
Feb 18, 2013
I need to break into a 2901 router to recover the passwords. Cisco's methodology for password recovery on 2900 seriews routerssays to remove the compact flash card and reboot into RMON. There is no external compact flash card on a 2901. Is there acompact flash card inside the box? Or can you use the older method of rebooting and then hitting ctl+break to boot into RMON?
View 5 Replies
View Related
Jul 10, 2011
i have a cisco 2811 series router and using for internet router and is working fine.i disabled its password recovery process from router cli like
NO PASSWORD RECOVERY Process Enable now i forgot its username and password and need to recover its password.
View 2 Replies
View Related
Dec 5, 2012
I'm using the ctrl-break sequence in hyperterminal during the the initial boot, and it's hanging.
View 1 Replies
View Related
Oct 31, 2012
I am trying to run the following commands on a 2801 router, but the commands are missing:
mls qos
mls qos map cos-dscp 0 8 16 40 32 46 48 56
The only QoS command i have in global config is (no MLS qos) :
REMOTE-ROUTER1(config)#qos ?
restore-show-output Restore old show output
shape-timer Set the HQF shape timer interval
The router is running IOS:
System image file is "flash:c2801-ipbasek9-mz.151-4.M5.bin"
Am i just running the incorrect IOS or am i missing somehting, i need to change the QoS Map for my Nortel VoIP. The VoIP phones connect to a 3750 PoE which used to conenct to a 2651XM to route VoIP and data traffic over the same copper pairs (WAN link to hub site) hence the need for a Service policy but being Nortel phones, require changing the cos-dscp map. the 2801 is going to replace the 2651XM using a new HWIC.
View 4 Replies
View Related
Apr 25, 2011
I am not able to configure Service policy output command in Cisco 2921 router.While configuring I am getting below error.Same config is working fine in Cisco 3845 router.I am suspectting the problem with license in IOS.
View 3 Replies
View Related
Jun 6, 2011
I run 2801 with 124-24.T3 and I have following problem: router is connected to internet over pppoe and ISP once per day breaks this link. so I get:
Jun 7 19:31:56.639 MSK: %DIALER-6-UNBIND: Interface Vi2 unbound from profile Di1
Jun 7 19:31:56.663 MSK: %LINK-3-UPDOWN: Interface Virtual-Access2, changed state to down
and I also have tunnel interface which endpoint is accessible over internet.
so I get:
Jun 7 19:31:56.679 MSK: %ADJ-5-PARENT: Midchain parent maintenance for IP midchain out of Tunnel1 68844500 - looped chain attempting to stack
Jun 7 19:31:57.635 MSK: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access2, changed state to down
Jun 7 19:31:59.199 MSK: %TUN-5-RECURDOWN: Tunnel1 temporarily disabled due to recursive routing
this is not a problem, problem is that router when interface goes down removes service-policy output from it, so I receive such message every day from runcid:
ip ospf cost 1
ip ospf mtu-ignore
tunnel source Loopback1
tunnel destination 192.168.200.199
- service-policy output tunnel_mpr_gre
and have to restore policy manually.
View 1 Replies
View Related
Jan 8, 2012
One of my remote office router model is Cisco 2801. Unfortunately I forgot the telnet/vty password of that router. I am sitting 500 KM distance in between in the Head Office. I can ping the router but due to lost password I cannot login to the router. Moreover I dont have snmp enabled in that router. Is there anyway I can reset the router's password remotely from my head office. Additionaly I have a switch directly connected to the router and I can ping and login to the swtich but not the router. I am writing this about the switch or resetting the routers password anyway.
View 1 Replies
View Related
Oct 20, 2011
where I can find a CLI password recovery procedure for the administrator account?
View 1 Replies
View Related
Nov 18, 2011
I have problem recovering my cisco 501 pix password. I followed instructions on this pageurl... but it seems its not working. I cant ping my TFTP Server on my pc. I tryed to disable firewall on my pc, i did a fresh install Windows but still i cant ping my TFTP Server on my PC.
View 8 Replies
View Related
Dec 13, 2011
As I make a password recovery to a Cisco PIX 525 Version 6.3(3)?
View 1 Replies
View Related
Jun 1, 2011
I just bought one of these in and it was in production and I have no way of getting a hold of the login information. Is there a way to wipe these to factory defaults? I have been looking everywhere with no such luck.
View 2 Replies
View Related
May 6, 2011
I am a student pursuing a CCNA certification currently. I recently came across a lot of 3548 xl switches. They power up fine, post with out problem and load flash. The problem I am running into is that the console is password protected. I have found the password recovery procedure for this switch, but it requires the use of the mode button. I have tried this process several times and the flash file is loaded with the startup config file. How do I perform a password recovery on a switch with a broken mode button?
View 1 Replies
View Related
Apr 10, 2012
how to recover ACS 5.0.021 CLI password.I dont have 5.0.021 cd with me can i use 5.2 cd to recover the same ?
View 1 Replies
View Related
Mar 12, 2012
To configure my Cisco, I use the console cable but as I have no serial port on my PC, I use a USB to serial cable which I plug the console. I had lost this USB cable -> serial but I found another one. So I started to configure my Cisco by copying from an existing config. I found out that a prior the converter is defective and copy the wrong config.
I had copied the enable secret password and it badly copied! No luck, I made a copy run start. Therefore more accessible to Cisco! When I start the Cisco, I see what activated "the Mechanism password-recovery is enabled". so I followed the procedure Cisco
I go flash_init: OK but when I type "load_helper" Unknown command it say to me .... I'm stuck!
The model is my Cisco: Cisco WS-C2960G-24TS-S
SW Version 12.2(55)SE3
Sw image C2960S-UNIVERSALK9-M
View 3 Replies
View Related
Oct 2, 2011
I have a couple of 877s which have "no service password recovery" set and something has happened to the flash or the IOS has been lost for one reason or another.
When trying to boot the routers, they all display similar to this, which then repeats:
[code]....
Or words to the effect of there being no IOS at all, unable to boot, but the result is the same, it just loops and there's nothing I can do to break the sequence!
I've tried taking the flash from a working 877 and replacing the card but this doesn't work and unfortunately, putting the once working strataflash card back in the working 877, it gets the same problem!
View 11 Replies
View Related
Jun 26, 2011
I have a cisco 515e pix but where I bought it from did not get the machine back to default. I boot it up and get to the user prompt, type enable and it asks for a username and then a password. I am new to this and am have no problems with router and switch password recoverys but when I look at the cisco documentation it is a bit overwhelming and I am not quite sure what it is that they want me to do to fix this. I have downloaded all the password recovery software loads and have the one I need for 6.x which is what the box is running I am just not sure what it is that I need to do. Can I use that recovery software from directly from my pc using a tftp server?
View 1 Replies
View Related
Aug 3, 2012
I need to recover switch enable password, i have already configured AAA also, when i am tryig to follow below proceedure finally saying Authorization failed. how can i recover enable password,If I try to recover password like this description says [URL]
Step 1 Connect a terminal or PC with terminal-emulation software to the switch console port.
Step 2 Set the line speed on the emulation software to 9600 baud.
Step 3 Power off the switch. Reconnect the power cord to the switch and, within 15 seconds, press the Mode button while the System LED is still flashing green.
Base ethernet MAC Address: 00:0x:xx:xx:xx:xx
Xmodem file system is available.
The password-recovery mechanism is enabled.
The system has been interrupted prior to initializing the flash filesystem. The following commands will initialize the flash filesystem, and finish loading the operating system software:
flash_init
load_helper
boot
[code]....
View 1 Replies
View Related
Oct 17, 2011
where I can find a CLI password recovery procedure for the administrator account?
View 2 Replies
View Related
Nov 27, 2011
I have a 4404 running firmware 7.0 and something happened (don't think it was a hack), but all of a sudden I can't login to the box via web or ssh or even telnet.
In trying the recovery procedure, I get a lot of messages scrolling through and cannot do the Restore-Password command on the CLI.
I'm attaching the whole capture, but here's a truncated capture from the procedure:
*fp_main_task: Nov 21 10:39:46.501: sshpmGetCID: comparing to row 0, CA cert >bsnOldDefaultCaCert<
*fp_main_task: Nov 21 10:39:46.501: sshpmGetCID: comparing to row 1, CA cert >bsnDefaultRootCaCert<
[Code].....
So as you can see, my prompt to enter the command is taken up by this fp_main message and it uses up the first and only time I can enter this in. I'm trying everything I can to not have to go back to factory defaults.
View 24 Replies
View Related
Aug 23, 2012
How is-it possible to do a recovery password for sysadmin on ADE-OS ?We're using LMS 4.2.1 and my customer doesn't remember the username and password created during installation.We have the admin user for the https connection.
View 4 Replies
View Related
Sep 19, 2012
I wanted to do with my Cisco 2800, a password recovery. I have read the instructions and Cisco just came up at six.
Complete these steps in order to recover your password:
Shut down the router. Remove the compact flash that is at the back of the router. Power on the router. Once the Rommon1> prompt appears, enter this command:
confreg 0x2142Insert the compact flash. Type reset.
BUT I had forgotten to plug the flash card. And now comes via console hieroglyphics only
View 1 Replies
View Related
Jan 7, 2013
I have 3 x ASA 5510 & 2 x ASA 5520, that require resetting back to factory default, the customer has removed the External Flash Cards, and i've checked internally on each unit the Internal Flash car is still present, is it possible to run a password recovery then a factory reset? and how would i go about resetting each unit to the new configuration.
View 8 Replies
View Related
May 31, 2010
the " password recovery functionality is disabled " service is running on the system .
im trying to access rommon in a Cisco 851, with not much success, i am sending a break after the image is loaded ( in the time frame that is allowed for that) .
View 13 Replies
View Related
