Replace Standard Modem With Wireless?
Sep 26, 2011can you replace the standard wired modem provided by your ISP with a wireless/wifi modem yourself?
View 4 Replies
ADVERTISEMENT
How To Connect Standard TV To Cable Modem
Apr 13, 2011I wanna subscribe to Internet TV. To watch it on computer screen I need to log in to the site where I registered, i.e. enter my login ID and password. But I want to watch it on my TV WITHOUT my PC. I realize that I have to buy a TOP BOX , connect it to TV and to cable modem. The question is how the TOP BOX knows my login and password to pass it to the site through modem.How do I enter it to tob box?
View 2 Replies View RelatedHome Network :: ISP Bandwidth Throttling - How To Replace Modem
Sep 29, 2012I think that my ISP is throttling my bandwidth at the modem . how access full available bandwidth.When the technician installed the fibre optic line and then the modem, he showed me an amazing 77MB/s (about 600Mbps) before the modem!!But after the technician left these were the test results after the router:
1) SpeedTests.net:
averages, after router, show: UP between 56/60Mbps & DN 45/75Mbps
2)Local Server Speed Test:
average: UP 45Mpbs & DN 170Mbps
A Japanese Internet savvy guy explained that NTT East throttles the available bandwidth at the building by specific apartment/modem settings related to individual contract bundles. I signed up for the top bundle: TV, Phone and Internet connections.This is my Hardware/ software setup:
OS: Win7,
Line specs:
Line type: IEC60874-14
Connector type: SC
Core across: 9 micrometers
Clad across: 125 micrometers
ITU-TG-652
NTT East fibreoptic TV/Internet/Telephone bundle (100Mbps best effort) Hikari Next Family Type but 10Mbps is considered within parameters
Asahi ISP Internet contract
Modem:
GE-PON (WAN+Coaxial TV antenna)
"SCM-GE-PON-<H>A GV-ONU D<1>" model
Router:
RT-S300HI (4 Giga ports + 1 phone)
Router & Modem have Japanese firmware which I cannot understand and, according to the NTT East, I must rent both modem and router from them and "will not support any other modem/router setup".I could not understand if it was because of technical or contractual limits.
I have tried to test my throughput after the modem but I could not figure out where the DNS, IP, WAN etc strings of numbers should go and, in the end, I simply cannot connect to the internet from my laptop directly to the modem so I cannot perform the same speed tests after the modem.
Replace Speedtouch 330 Modem With Netgear Router Dgnd3700?
Dec 16, 2012install a new N600 Wireless Dual Band Gigabit ADSL2+ Modem Router - Model DGND3700, to replace a Thompson Speedtouch USB Modem.
PC Windows XP Home Premium Media addition - Main PC X2 Laptops Win7 & Vista - fully working on wireless no issues.
I have managed to get two laptops working wirelessly with no problems, my main problem is the master pc needs to be able to use this router as well, but I cannot get it to work via the Ethernet cable!! I can get to to the Routers config page, I have done the following:
unplugged and removed the speedtouch modem, the old dial up connection is still available on the pc along with the speedtouch software and driver, I left this in place just in case the pc needs to revert back to the speedtouch modem, if I am unable to resolve this issue.
I have set the ip address on the PC to static and input the relavent Subnet and Gateway I can ping the Routers address 192.168.0.1 even though I have reserved the PC's Mac address and IP Adress I am unable to get to the internet. I have tried setting up a new internet connection via windows wizard.
when i look into the nework connections section in windows the local area connection is 100mb and there seems to be another connection which looks like another internet connection this indicates I am connected however I still cannot get an actual google session running.
Cisco WAN :: Replace Modem With 2621 Router With WIC-1ADSL Module
Dec 26, 2012I have a Cisco ASA5505 with Frontier ADSL. I broke into their crappy little modem and obtained the settings needed to replace their modem with a 2621 router with a WIC-1ADSL module. I have a static IP from Frontier which is on my ASA5505 and the Dialer interface on the 2621 gets its address from Frontier via DHCP. There are devices behind the ASA which I need access while in the field, IP Cameras, Seed Treater, etc., so I have Anyconnect running on the ASA and can access everything from my laptop, iPhone and iPad from whereever. The issue arises when my laptop is in house and communicating with my parent company and I try to make a cell phone call off the network extender. The call is choppy since there is no QoS and the data is strangling the voice. Since I have control over the 2621, I added another network and NAT it into Frontier without them knowing. I have since placed the network extender on this network as well as a WAP200 that is wide open for my customers when they are in the office. Doesn't fix the problem but...
I have now added Evertek Wireless internet with a static IP also but they use a reservation based on the MAC Address of my interface of the ASA. This plugs directly intot the ASA via ethernet (I would assume their antenna is just a wireless bridge). I set route tracking on the Evertek side and use the Frontier as a backup and all devices on my NAT network still funcion on Frontier DSL and all my nornal data traffic is out Evertek. The issue is that the Evertek Wireless is not very fast or reliable (today in during a snow storm, it could barely keep an internet connection). And I had a problem with Anyconnect using either connection. I got that working. But think that the "ip address x.x.x.x y.y.y.y dhcp setroute" on the Evertek side messed things up from a routing standpoint when I would connect from the outside on the Frontier side. For testing, I switched the tracking around and now the connection on the Frontier side does not work but that is besides the point.
Frontier is going to try out an ADSL/2 connection next week which brings up another issue; all Frontier connections come into my buidling on a single 4-pair wire so if they go down, all my internet except the Evertek goes down. I have a Raven Slingshot coming for installation shortly that cannot go down; it will provide RTK (sub-inch accuracy GPS) to my customers that have auto-steer and auto-shutoff capabilities in their tractors via cellular data modem. So, while they are planting their crops in the field, if my connection goes down, their tractor will not function.
I also had a Cisco UC320W but it died a few days after it went off warranty so I replaced it with a Dell Server running 3CX IP PBX that supports Cisco SPA525G2 and SPA501G IP Phones. There is a 3CX iPhone app that allows me to receive calls while in the field, it uses a proprietary tunnel that I have open on the ASA. With 4-pair coming into my building, I will be left with a single 1-pair for phones so I am considering a SIP provider instead.
Can/should I move the Evertek ethernet to the third ethernet interface on the 2621 and track the Frontier DSL against the Evertek (backup) on the 2621 side and use the ASA to track the ADSL/2 against the 2621? Should I acquire an 1841 (or some other device that suppports the HWIC) with a ADSL/2 card and use HSRP between the 2621 and 1841? Is that even possible?
Linksys Cable / DSL :: Wag320N Modem Router To Replace Two Wire Device
Mar 14, 2012I've recently bought a wag320n modem router to replace the two wire device fitted to my bt business broadband. This router supports a guest network..
View 1 Replies View RelatedCisco Wireless :: 5508 - MSE Running 7.0.220.0 Work With WCS-standard-K9-7.0.240.0
Apr 10, 2013Can MSE running software 7.0.220.0, work with WCS runing WCS-standard-K9-7.0.240.0 and WLC 5508 running AIR-CT5500-K9-7-3-112.0 ?
View 1 Replies View RelatedCisco :: Disable G Wireless Standard On Single WLAN WLC 5508
Mar 17, 2013We have some older Honeywell Dolphin 7900 Series Handhelds that have issues with wireless communication. Very unreliable communication. One recommendation from Honeywell is to disable the G standard and only allow B. Basically have a WLAN that is solely b radio enabled. I see that their are options to go B/G only or A only, but no options in the radio policy to go B only.
We are using WCS 7.0.240 and the controller is a WLC 5508 running the same code revision.
Is this doable on a single WLAN while leaving G available on other WLAN's?
Replace A Wireless Card In My HP DV6000?
Feb 17, 2012I have a HP DV6000 Laptop. The wireless coverage is not very good and I was thinking of upgrading the Wireless card to something better. The current card is HP Pavilion DV9000 PCI-Express Wireless WIFI Card 802.11a/b/g 441075-001 by HP. Is it even possible to install another card in the laptop or does HP limit what you can put in this laptop
View 3 Replies View RelatedCisco Wireless :: Replace 352 Bridged Network With 1552s?
Mar 20, 2012I have a question concerning replacing a 352 bridged network with 1552 mesh access points. Theoretically, imagine a centralized 352 with an omnidirectional antenna that is linked to multiple 352's with yagi antennas in a hub-spoke fashion. If this central 352 is replaced with a 1552 access point, will the existing Yagi's be able to talk to the 1552? I understand that the Yagi's AP's should be replaced with 1552's as well (thus forming a mesh network as the 1552s are designed to do) but for the sake of theory please assume the 'spoke' 352s will not be replaced. I have the understanding that the 1552s communicate over the 802.11a for the backhaul so I'm thinking this would cause some issues with the 352's.
View 2 Replies View RelatedCisco Wireless :: Replace 4402 With 5508 Controller
Oct 6, 2012I'd like to replace my 4402 Wireless controller with a new 5508. I have migrated the exact configuration from my 4404 controller to the 5508 and they are both running the same version of code. I'm worried that if I replace the 4402 with the 5508 controller, the Access Points will not rejoin to the new controller or they will join but will have lost their configuration e.g. AP Name/location etc etc. AP models registered to the existing controller are 1131, 1142 and 3502. I am also using Cisco WCS.
As long as the new controller has the exact same configuration, is it possible to replace the 4404 with the 5508? Will the existing Access Points join the new controller? Is there any other configuration required? I have read about doing this using mobility groups however would rather not if possible.
Linksys Wireless Router :: Replace WAG54GS Gateway With EA6500?
Jan 4, 2013I am looking to replace my current WAG54GS Gateway with the EA6500. Problem is the new one does not have a built in ADSL2+ modem (I am in the UK and my ISP is Demon Internet). I therefore need to purchase a separate Modem to connect to the router.
View 9 Replies View RelatedCisco Wireless :: Replace WLC2504 To WLC5508 Without Service Interruptions?
Mar 12, 2013how can i replace my wlc2504 to a WLC5508 without disconnecting everybody, i have 3 SSID, on different VLAN.. I want the WLC5508 to be the main WLC, so i can remove the 2504 from the network. On the WLC5508, it will be the same configuration of the 2504. Is there a procedure or a wiki on such operation?
View 8 Replies View RelatedLinksys Wireless Router :: To Replace Dying Netgear FWAG114
Sep 6, 2011I need to replace a dying Netgear FWAG114 wireless router, and the E4200 gets good reviews so I've been looking into it. I'm a software developer running 6 servers plus 3 laptops and 5+ other devices (iPad, Wii, Droid phones, BluRay...). I prefer to use a trusted PC list (enter MACs for all trusted devices) rather than WEP or WPA - is this available with the E4200?
I don't need VPN, but I do run a number of web servers, app servers and databases, so port forwarding is important - I notice the E4200 provides port range forwarding and single port forwarding - I assume this replaces the Rules and Services feature in Netgear - right?
Do you see any potential problems, given my needs, in using the E4200?
Linksys Wireless Router :: E1500 What Is Best Notebook Card To Replace Broadcom
Jul 13, 2012I own an HP Pavilion dv6 Notebook PC and recently purchased a Cisco E1500 to replace my aging WRTG54 wireless router. Since installation of the new router I keep getting dropped from my LAN and the internet with "connectivity issues" ... this only occurs on my notebook PC and not the other wireless devices I have in my home. I’ve done some searching on the internet and this seems to be a generic problem with the Broadcom 802.11b/g/n card the notebook uses. I have 2 questions:
1) Is there an easy way to adjust either the card or the router to deal with these issues and if not then
2) what is the best notebook card to replace the Broadcom with to assure these issues go away.
Upgrade From G To N Standard?
Oct 3, 2011dell xps m1530 i have a Intel� PRO/Wireless 3945ABG Network Connection and i want to upgrade it to N standard which model of intel minipci network will fit to my dell?
View 4 Replies View RelatedSpecifying Which Version Of 802.11 Standard To Use
Oct 25, 2012Is there a way that I can specify which version of the 802.11 standards I can use.e.g. I have an 802.11 B/G/N wireless card and I want to test each on a directional antenna to see how they perform
View 4 Replies View RelatedTP-Link ADSL2+ Wireless :: Setting Up W8968 To Replace Router Given By TM For Unify Connection
Feb 24, 2013Region : Malaysia
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP : TM
I am having difficulty setting up the W8968 to replace the router given by TM for the Unifi connection.I tried updating the firmware of the modem router and used quick setup to configure the device as a wireless router using PPPoE, but still couldn't connect to the internet using the WAN port.I noticed there was a guide for TD-W8960N to set up TM Unifi but the web interface is too different from the W8968 interface.
Linksys Wireless Router :: WRT600N Standard Verizon Router Doesn't Have N Capability
Apr 6, 2012The standard Verizon router doesn't have Wireless N capability, so I got the WRT600N (first floor) a while back and connected it to one of the ports on the Verizon router (basement). I have the wireless turned off on Verizon router. My problem is that anything connecting to the WRT600N has extremely intermittent connectivity.
View 1 Replies View RelatedWhat's The Standard Protocol To Transfer R2 To SIP
Apr 19, 2011what's the standard protocol to transfer R2 to SIP?
View 1 Replies View RelatedCisco WAN :: 881 To Use Ntp As Standard Feature
Nov 25, 2012I can see that the Cisco 881 does not have NTP as standard, but can this feature be used anyway with the latest software upgrade?
View 4 Replies View RelatedLinksys Wireless Router :: WRT54G Replace XP Machine With Wired Desktop Running Windows 7
Apr 28, 2010I have a Linksys WRT54G router; have a cable internet connection through the router; and two wired desktops, one running Vista (32-bit) and the other XP. I would like to replace the XP machine with a wired desktop running Windows 7 (64-bit).
View 8 Replies View RelatedServer 2008 R2 Standard Install
Apr 19, 2011Can I install win2008r2 standard to a 500gb usb ultra portable harddrive and connect it to my net book and run it ? I am studying for the MCITP and want to use it for that purpose?
View 3 Replies View RelatedInternet Does Not Work On Standard Account?
Sep 6, 2012Tech Support Guy System Info Utility version 1.0.0.2[CODE]
View 6 Replies View RelatedCannot Get Any Of The Standard Ports Open On Computer
Jun 2, 2011why I cannot get any of the standard ports open on my computer. I have run ESET firewall/antivirus, but have it temporarily disabled. I have windows defender disabled. I have the correct ports open/bypassed through my linksys router, but still am having network trouble.
Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft Windows 7 Enterprise , 64 bit
Processor: Intel(R) Core(TM) i7 CPU 920 @ 2.67GHz, Intel64 Family 6 Model 26 Stepping 5
Processor Count: 8
RAM: 6135 Mb
Graphics Card: ATI Radeon HD 4800 Series , 1024 Mb
Hard Drives: C: Total - 953866 MB, Free - 610614 MB;
Motherboard: ASUSTeK Computer INC., P6T DELUXE V2, Rev 1.xx, MS1C96B19100148
Antivirus: ESET Smart Security 4.2, Disabled
Adding Non Standard Device To Network?
Oct 18, 2011I have a machine which is connected to a PC using an ethernet cable to communicate information between the machne and computer.I am told that the machine uses the MAC address to communicate and the computer just needs an ip address in the same range as the machine and software aware of the machine's MAC address. Why I can't connect it though the network, I tried the manufacturer who couldn't explain
View 4 Replies View RelatedCisco :: Difference Between Custom And Standard Discovery In LMS 4.2
Oct 22, 2012whats the difference between custom and standard discovery? There´s a line on the help page: "The Use Policy Configuration Settings radio button will be enabled only after adding a Default Credential Set Policy."The radio button is not enabled although I´ve two default credential sets and two default credential sets policy configuration.
View 1 Replies View RelatedAdd New DMZ Zone To Network With Standard 1941 (1x LAN / 1 X WAN Port)?
Jan 2, 2012I am looking to add a new DMZ zone to our network with have a standard 1941 (1x LAN / 1 x WAN port) and so I need a 3rd routable L3 interface to create the DMZ.
Is the HWIC-1FE what I am looking for or is there another way to do this?
Cisco :: LMS 3.2 And Window Server 2008 R2 Standard
Jun 23, 2011We have bought lms 3.2 and window server 2008 r2 standard. Now we know, it cant be used together Could we upgrade to lms 4.0.1 ? If so, how can we do ?
View 2 Replies View RelatedNetworking :: SBS 2003 Migration To 2008 R2 Standard
May 15, 2012I have a client who does not use exchange, and doesn't need any of the SBS features.Their server is aging and are running out of disk space.
I'm in the process of building them a new file server and am considering using Server Standard 2008.I am even going to take them off the domain and make their server strictly a file server for Peacthree. It is the only reason they even need a "server".
Realtek PCIe GBe Family Controller - Standard Gateway Not Available
Feb 6, 2011I have just upgraded my computer and now i have a Gigabyte 870A-UD3 mobo with a Realtek PCIe GBe family Controller and i have now gotten the famous "Standard Gateway not available" or something.
View 3 Replies View RelatedCisco Switching/Routing :: 10.2.2.2 / Can Use Standard ACL In Route-map For BGP Fall-over
Jan 22, 2012I haven't got time to test different configurations yet. Just want to quickly ask here about the fall-over route-map configuration. I saw lots of example using pip prefix-list to specify the next-hop for tracking. Is that the only way you can do it? Can you just use a standard ACL to specify that host like permit host 10.2.2.2? ip prefix-list will do like ip prefix-list seq 5 permit 10.2.2.2/32. And you apply the prefix-list to route-map then. ACL will work?
View 2 Replies View RelatedCisco Switching/Routing :: 3750 / MST Pre-standard And Links Down
Sep 3, 2012Checking the logs we have seen the following messages:
%SPANTREE-3-PRESTD_NEIGH: pre-standard MST interaction not configured (Port-channel3). Please, configure: 'spanning-tree mst pre-standard' on ports connected to MST pre-standard switches.
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/1, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2/0/1, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Port-channel3, changed state to down
%LINK-3-UPDOWN: Interface Port-channel3, changed state to down
%LINK-3-UPDOWN: Interface GigabitEthernet1/0/1, changed state to down
%LINK-3-UPDOWN: Interface GigabitEthernet2/0/1, changed state to down
When this happened, the interface that was actually blocked by STP didn't come to forwarding state, and as a result this switch became isolated.This switch is connected to a switch that runs standard MST, and to some switches that run PVST but have bpdufilter enabled as we don't want them to participate on the STP. It is a 3750 switch with software version 12.2(55)SE5.
As far as I knew, when a MST pre-standard BPDU was received, the interface was able to receive more pre-standard BPDUs, but I didn't know it would turn the link down. Why the links went down, and if there is any way we can configure those links to accept only MST standard BPDUs.
I would also like to know if there is any chance a switch running PVST can send a MST pre-standard BPDU if it has a software version 12.2(25)SEE3.