Cisco Wireless :: Replace WLC2504 To WLC5508 Without Service Interruptions?

Mar 12, 2013

how can i replace my wlc2504 to a WLC5508 without disconnecting everybody, i have 3 SSID, on different VLAN.. I want the WLC5508 to be the main WLC, so i can remove the 2504 from the network. On the WLC5508, it will be the same configuration of the 2504. Is there a procedure or a wiki on such operation?

View 8 Replies


ADVERTISEMENT

Cisco Firewall :: Interruptions Of Connection Through ASA 5520

Dec 12, 2012

I have a problem with the connections to the remote webservice passing through ASA 5520 firewall. Connections are usually  interrupted in perod of half an hour in every few days.
 
This ASA 5520 firewall is only one firewall in a path to the remote webservice.
 
During the interruption I find the logs:
 
UTC: %ASA--4-419002: Duplicate TCP SYN from dmz1:x.x.x.x/.... to outside:y.y.y.y/p with different initial sequence number
 
Teardown TCP connection 28309406 for outside:y.y.y.y/p to dmz1:x.x.x.x/.... duration 0:00:30 bytes 0 SYN Timeout
 
How I could find root cause? Could it be solution implemetation of TCP State Bypass?

View 1 Replies View Related

Cisco Switching/Routing :: 3750G MSTP Traffic Interruptions

Feb 15, 2013

we have 3750G stack connecting to H3C switch cluster connecting through two trunk portchannels.and we have MSTP configured since H3C support only MST.MST is configured as below.instance 1 1,168,178,198instance 2 148,158,188,instance 1 LANS are extended to H3C,instance 2 VLANS are local to 3750 stack.,As a new requirement we need to add a another VLAN to this topology.and we are planing to add this VALN to instance 1,can there be any traffic interruptions.

View 2 Replies View Related

Cisco Wireless :: AP3502I-E-K9 Cannot Join WLC2504

May 23, 2013

I have WLC 2504 and AP3502I . AP can not join wireless controller .
 
*May 24 16:33:51.871: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*May 24 16:33:51.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 10.80.90.99 peer_port: 5246

[code].....

View 9 Replies View Related

Cisco Wireless :: WLC2504 Can't Create Interface On WLC Of Static IP

May 18, 2013

I need urgent support on creating SSID as layer 2.We have cisco WLC2504 and 1602i access point. In our network we have in gate for guest.I want to create one ssid and bind with vlan only. We can not creat interface on WLC b/c of static IP.

View 3 Replies View Related

Cisco Wireless :: How To Activate Mesh Software In WLC2504

Nov 9, 2011

I have two Wireless LAN Controllers 2504 and 8 APs 3502e. The WLCs are running software version 7.0.116.0. The problem is that I don't have the mesh option to configure indoor mesh inside the controller. In chapter 9 of Wireless LAN Controller Configuration Guide, Release 7.0.116.0 says that I have to go to Wireless Menu and select the AP. When I am inside the AP general page, the guide says I have to go to the Mesh tab, but that tab doesn't appear in the controller GUI. Do I have to use another image in the controller? Or do you have to use an special mesh code or something like that? Because in the download page of the controller it only appears the 7.0.116.0, two more new versions but there is nothing about mesh image.

View 5 Replies View Related

Cisco Wireless :: Aironet 1130 Can't Join WLC2504?

Aug 13, 2012

I have the problem that the AP1130 can not join to WLC2504.
 
Console Messages of AP1130:
  
*Aug 14 09:34:54.029: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Aug 14 09:34:54.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.x.251 peer_port: 5246

[Code].....

View 10 Replies View Related

Cisco Wireless :: WLC2504 - Network Lan Sharing Not Working?

Oct 29, 2012

1) We have client setup, which has all PCs in Workkgroup , client has network sharing enable in LAN . Its work well in LAN , he don't have Local DNS , still he is able to ping or access sharing using device hostname

2) When Client moves into Wireless , he is not able to ping or access sharing using Hostname , but if  used the ip details he is able to ping and do sharing using IP address onlye.
 
My Wireless Setup has WLC2504 and LWAPP Access Points.

View 5 Replies View Related

Cisco Wireless :: WLC2504 - WLAN With Win2k8 NSP Not Working

Jul 8, 2012

I am having issue with integrating WLC2504 with Win2k8 server NSP radius server.

View 3 Replies View Related

Cisco Wireless :: WLAN Support For WLC2504-25 License

Oct 25, 2011

I have few question with WLC 2504 with 25 License AP. Our customer have SSID around 30 SSID then, is it possible to create WLAN around 30 SSID on WLC 2504? becuase i had tried to do it on WLC4404-25 License that can do or create WLAN with 30 SSID.

View 12 Replies View Related

Cisco Wireless :: WLC2504 - Configure Clients To Access 802.1x?

Jul 4, 2012

configured Cisco 2504 WLC with 1142 Aps...  Guest wireless works fine
 
for the staff wireless I wanted to authenticate with 802.1x & Radius. So configured an external Radius server (Imprivata) and configured the 2504 Radius options for the extenal server.( Layer 2:  WPA2-AES & Auth Key Mgmt:  802.1x )
 
When I connect a client to this wireless, the authentication fails, I wonder whether it is because of the client side settings..
 
Which trusted Root Certification Authorities need to be checked?

View 3 Replies View Related

Cisco Wireless :: WLC2504 - Controllers Loses Current Time

Jan 22, 2013

Every time I power down my WLC2504 controller and then back up, the time reverts back to the year 2000.The APs can't join the controller, due to certificate errors, until I reset the clock.  This problem just started recently.

View 6 Replies View Related

Cisco Wireless :: WLC2504 - Can Internal Web Authentication Be Used For Guest Network

Mar 18, 2012

Can we change the internal web authentication for guest network to use http instead of https?

View 3 Replies View Related

Cisco :: WLC2504 And Using PoE Ports In Same LAN

Apr 10, 2012

I've set up a WLC2504 with interface "mgmt" and "guest" (2 different VLAN IDs) both configured on port1.Now I'd like to be able to connect to PoE ports (port 3 and 4) 2 LAPs which should be able to get IP addresses from the DHCP as if they were connected to port1.

View 14 Replies View Related

Cisco Wireless :: WLC5508 - Backup WLC Across A WAN?

Jan 29, 2013

Currently we have 20 remote sites, each with 2-5 AP's each. They all connect back to our Main Data Site in the US and register on a single WLC5508.

We do not have a backup WLC, but are looking to purchase one. What I would like to know is, are there any problems with the secondary WLC being installed in our Main Data Site in Europe? These two main sites are connected via a 10M MPLS WAN.
 
So all the remote sites could still connect to the WLC in the US, but in the event of a WLC failure in the US, they would need to fail over to the site in Europe

View 5 Replies View Related

Cisco Wireless :: WLC5508 Client Can't Get Its IP

Feb 6, 2013

I'm using WLC5508 /w 7.0..My client do not get its IP. Status shown "DHCP_REQD".I found in (Cisco Live) Troubleshooting Wireless LANs with Centralized Controllers  This related with Enable/Disable DHCP Proxy checkbox. I solved. with Enabling this.But,
 
1) Why this box have been working correctly for longtime? No one did diable/enable this feature on my box.

2) I guest, ver7.0 Disables this chechbox by default. Or not? I also have others two 7.2 boxes. Those are all Enabled.

View 7 Replies View Related

Cisco Wireless :: WLC5508 - Client Cannot Get IP From Ex DHCP

Feb 4, 2013

I have a WLC5508 , we are using external DHCP for WLANs
 
one WLAN is able to get IP  from DHCP server but another WLAN not , the DHCP server is same , only 2 different scopes.
               
This is debug
 
*DHCP Socket Task: Feb 05 21:26:43.106: e8:06:88:9b:a8:04 DHCP received op BOOTREQUEST (1) (len 308,vlan 1, port 1, encap 0xec03)
*DHCP Socket Task: Feb 05 21:26:43.106: e8:06:88:9b:a8:04 DHCP processing DHCP

[Code].....

View 2 Replies View Related

Cisco Wireless :: VMware Cannot Get DHCP When Using WLC5508 V7.2

May 7, 2012

I have some problem about dhcp via VMware 7.1. My client connect the wifi and get ip address well, then, i turn on VMware (inside my computer) and set as the bridge mode. I found that my VM cannot get the ip-address from dhcp server and I using WLC5508 version 7.2. I try to connect via Switch, my VM get the ip address well.

View 1 Replies View Related

Cisco Wireless :: Configuration For WLC5508 To Be Used For Site

Jun 6, 2012

looking at doing the site survey before detailed implementation. we plan to use a wlc5508, AP3602, a good tripod/stand, PoE switch and AirMagnet to conduct the site survey. i'm inclined to use a single AP and just a guest SSID and let AirMagnet merge the readings on where i 'locate' the AP (on 1 VLAN)

View 1 Replies View Related

Cisco Wireless :: Mesh And Flexconnect With WLC5508?

Apr 4, 2013

A customer have a bad coverage in a corner of his branch office. He like to add a mesh AP (MAP) in the near of that corner.
 
I checked allready the documention about Mesh but i'm not sure if Flexconnect and Mesh works togheter. This MAP is in a branch office and the WLC is in the head quarter therefore he likes to uses Flexconnect togheter with Mesh.

View 10 Replies View Related

Cisco Wireless :: WLC5508 WLC HA AP SSO And Number Of Interfaces

Feb 25, 2013

I have a customer who is going to deploy a WLC HA AP SSO setup. I have recommended them to have 4 Gigabit SFP modules in each WLC5508.The customer now asks if it is possible to only have one or two SFP modules in the standby unit ?  As he says it is properly not going to go in service one time within the next five years if he is unlucky.

View 5 Replies View Related

Cisco Wireless :: Setup DHCP On WLC5508?

Apr 17, 2013

Is it possible to setup DHCP on the WLC5508? If i have 2 or 3 VLAN with different Scope and IP range, how can i do?

View 1 Replies View Related

Cisco Wireless :: Upgrade WLC5508 To Version 7.4

Feb 6, 2013

We have five cisco WLC 5508 and one WCS .The WLC is running on 7.0.116.0 version at present but we want to upgrade it to 7.4.100.0 but on cisco site at download location , the below thing is mentioned...
 
WLC Version 7.4.100.0 will need Prime Infrastructure Version 1.3 to be  managed, Version 1.3 is not yet available to download at this point of  time
 
Access Point Model----Cisco 3501i Series
 
So i want to know, can i upgrade it to this version when we are having the WCS in our network ?

View 16 Replies View Related

Cisco :: Unable To Connect WLC2504 To 2960?

Mar 13, 2012

setting up a 2504 on a 2960 switch.  The management interface is up and pingable, and from the WLC we can ping vlan 20 (our wireless client vlan) gateway.  However, when we create the vlan20 interface on the WLC, give it a valid address and assign it to a port, we can no longer ping the vlan 20 gateway from the wlc, nor can we ping the vlan20 interface from a PC.  I’m told the 2960’s don’t do dot1q trunking…

View 6 Replies View Related

Cisco Wireless :: How To Import Configuration From 4404WLC To WLC5508

Feb 3, 2012

In one week I need to import the config from my 4404 WLC to my new 5508, then I just want to change the mgnt IP address of the 5508 and then bring it into the same mobility group.How do I import the config when the 5508 is straight out of the box?

View 13 Replies View Related

Cisco Wireless :: WLC5508 VoIP Connectivity Is Broken

Jun 22, 2012

I have a  WLC5508 and 25  LAP 1041. I use two wifi, one with RADIUS for data and other with wpa-psk for voip. The problem is the voip conectivity is broken.How can i improve the handover?

View 11 Replies View Related

Cisco Wireless :: WLC5508 With 6.0 Software - How To Replicate All Configuration

Sep 15, 2012

I have WLC 5508 with 6.0 software  and kept in main office and 10 sites are connected . I created Group and hreap for the sites AP.Now customer wants the secondary WLC to keep on one another site. And the customer is asking all the configuration like ap group and all should come to secondary wlc automatically . In future also if he create any new group in primary it should come in secondary wlc.And if primary goes down the secondary should controll all the sites and when comes up primary should taken care.Active standbye mode.

View 10 Replies View Related

Cisco Wireless :: Several Remote Sites And Centralized WLC5508

Nov 8, 2011

I have been asked to setup wireless and we have purchased WLC 5508 and 1142 APs.We have several remote sites and a  centralized WLC.  The requirement are to have a common SSID  (Corporate) advertised across all the remote sites and have that SSID locally switched, and have another two SSID Guest and Mobile tunneled back to the central site (WLC).I want all the wireless (Corporate) clients to use the same subnet as the wired clients at each remote site, the IP assigment will be done by a DHCP server at the central site. The Guest and Mobile users will use a common subnet each across all the site and this will also be handled by the DHCP server at the central site.
 
I have enabled H-REAP with Centralized  Authentication and Local switching but I'm not sure about the second  part which is to have a common SSID (Corporate) across the remote sites and localy switched whilst having the other two SSIDs tunneled back to the WLC. Cisco TAC told me to configure dynamic interfaces for each of the remote site but then he said I still wouldn't be able to switch the Corporate traffic localy if I use a different subnet to the wired subnet for the wireless clients.

View 12 Replies View Related

Cisco Wireless :: 1552 Outdoor AP Disappears From WLC5508

Dec 30, 2012

My problem ist that i have 4 air-cap-1552e APs witch are powerde trugh Power Injectors. They worked fine for a few days but then the controller (7.2.111.3) lose connection to them. Right now i have only one Joined AP. The other 3 are status not joined. I can Ping all 4 Aps and wifi clients are connected through them.

View 8 Replies View Related

Cisco Wireless :: WLC5508 Link To Switch Core Down?

May 16, 2012

I tried to implement WLC5508 in my network but when I came to connect it to the switch core which is a Catalyst 4000 the link didn't get up. This switch module is a fastethernet, I wonder if that might be the problem since I also tried connecting my laptop to the WLC and the link got up.
 
If that might be the cause, is it possible to get WLC to 100 Mbps?

View 5 Replies View Related

Cisco Wireless :: Minimal WLC5508 CLI Configuration To Access GUI?

Sep 8, 2010

I have on my desk a WLC-5508 that I need to setup to ship to a remote location. Normally we configure 4402 model and this model/version appears to be much different. I am trying to configure just enough via the command line to access the GUI via a laptop directly connected to the device. I’ve gone through the Wizard Configuration Tool where you set the hostname, admin account, and management interface (among other things). We use LAG and tagged VLAN on the management interface. I’ve been told in the past this is how we configured the 4402 models via laptop directly connected once the GUI is accessible, but with LAG enabled I don’t understand how a laptop could communicate via trunk, so I've disabled LAG and set the VLAN to untagged. In either case the laptop does not communicate with the WLC. Skipping ahead to my current setup I see the following information via the CLI:

(Cisco Controller) show>interface detailed management
Interface Name................................... managementMAC Address...................................... IP Address....................................... 10.1.1.20IP Netmask.......................................

[Code]....

View 6 Replies View Related

Cisco Wireless :: WLC5508 - Ipad2 Can't Join Wi-Fi Using Wpa2 AES

Apr 12, 2012

we have a cisco WLC 5508 on which few SSIDs are configured, and two kinds of APs: AIR-LAP1142N-E-K9 and converted AIR-AP1141N-E-K9.
 
When in WLAN settings we leave WPA2 policy and AES encryption, iPads2 can connect without any problems to AIR-LAP1142N-E-K9, but there is no connection to converted AIR-AP1141N-E-K9.  MacBooks, iPhones are connecting without questions.

When we set WPA2+TKIP everything is cool, but other Apple devices can't rich 802.11n speeds((
 
With only WPA2+AES or both WPA2+AES+TKIP enabled on a WLAN the WLC gets such messages :
 
Decrypt errors occurred for client xx:xx:xx:xx:xx:xx using WPA2 key on 802.11b/g interface of AP xx:xx:xx:xx:xx:xx
 
But I know that it can happen when you offer funny encryption combinations that client doesn't like (wpa1+aes, wpa2+tkip). But the advise to try to only enable wpa2/aes for some reason doesn't work.

View 15 Replies View Related

Cisco Wireless :: Configure 802.11n On WLC4404 Or WLC5508 In 2.4Ghz?

Aug 15, 2012

how to set up support 802.11n on WLC4404 or WLC5508 in the 2.4Ghz? WLC4404 supports 802.11n? or support this protocol only in the brochures? I spent a few days, but did not get the result. I'm connected at speeds 65/130Mbit, but the real speed tests never exceeded 45Mbit. The AP from the test laptop is 7-10 meters.I tested the laptops with a Linksys AP E1200-EE ( 40Mhz, FastEthernet uplink port...)and received nearly 100Mbit!
 
At WLC5508 able to connect at speeds 150/300Mbit/c but only in the 5GHz band, but real speed tests never exceeded 70Mbit.In 2.4Ghz range I connected at speeds of 130/144Mbit/c, but actual measurements showed no more than the 45Mbit.
 
All tested with iperf and with site speedtest.net.
iperf -w64K -s
iperf -w64K -i 2 -t 300 -c x.x.x.x
 
Laptops: Asus (Atheros AR9002WB-1NG) and Sony (Advanced-N 6230).
 
My tests AP: 3501I-E and 1252AG-A
SW on WLC5508 7.2.110.0
 
AP tested in different variants - open system and WPA2+AES.

[code]....

View 5 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved