I have few question with WLC 2504 with 25 License AP. Our customer have SSID around 30 SSID then, is it possible to create WLAN around 30 SSID on WLC 2504? becuase i had tried to do it on WLC4404-25 License that can do or create WLAN with 30 SSID.
View 12 RepliesI am having issue with integrating WLC2504 with Win2k8 server NSP radius server.
View 3 Replies View RelatedI wanto delete the Evalution License and i want to activate the permanent license. find the attached snapshot of License.
View 7 Replies View Relatedi have CSC-SSM-20 i want to renew the license to support 750 users for 3 years if i have base license only also if i have base and plus?
View 1 Replies View Relatedis it strange to have a valid license fro FL-WEBVPN10-K9 but not able to download the latest anyconnect for my router?
View 0 Replies View RelatedWe are moving forward with a mobility project which requires our network to authenticate/authorize based on certificates.
WLAN_1 has 802.1x enabled passing the cert through to the MS CA which authorizes the cred, which in turn passes the AD creds of the user to the MS RADIUS server for authenticate/authorization.
Hardware: WLC 5508 running 7.2.110.0 3600 APs ACS 5.2 not used for AAA
1. As we turn up additional SSIDs, we need Mobile SSID to accept ONLY the Mobile Cert, our Internet SSID to only accept the Internal Cert and our GUEST SSID to deny ANY Cert issued by our CA.I know ISE makes this much easier, but I dont have it and need this to work as best we can until next fiscal cycle..
I have WLC 2504 and AP3502I . AP can not join wireless controller .
*May 24 16:33:51.871: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*May 24 16:33:51.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 10.80.90.99 peer_port: 5246
[code].....
I need urgent support on creating SSID as layer 2.We have cisco WLC2504 and 1602i access point. In our network we have in gate for guest.I want to create one ssid and bind with vlan only. We can not creat interface on WLC b/c of static IP.
View 3 Replies View RelatedI have two Wireless LAN Controllers 2504 and 8 APs 3502e. The WLCs are running software version 7.0.116.0. The problem is that I don't have the mesh option to configure indoor mesh inside the controller. In chapter 9 of Wireless LAN Controller Configuration Guide, Release 7.0.116.0 says that I have to go to Wireless Menu and select the AP. When I am inside the AP general page, the guide says I have to go to the Mesh tab, but that tab doesn't appear in the controller GUI. Do I have to use another image in the controller? Or do you have to use an special mesh code or something like that? Because in the download page of the controller it only appears the 7.0.116.0, two more new versions but there is nothing about mesh image.
View 5 Replies View RelatedI have the problem that the AP1130 can not join to WLC2504.
Console Messages of AP1130:
*Aug 14 09:34:54.029: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Aug 14 09:34:54.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.x.251 peer_port: 5246
[Code].....
1) We have client setup, which has all PCs in Workkgroup , client has network sharing enable in LAN . Its work well in LAN , he don't have Local DNS , still he is able to ping or access sharing using device hostname
2) When Client moves into Wireless , he is not able to ping or access sharing using Hostname , but if used the ip details he is able to ping and do sharing using IP address onlye.
My Wireless Setup has WLC2504 and LWAPP Access Points.
configured Cisco 2504 WLC with 1142 Aps... Guest wireless works fine
for the staff wireless I wanted to authenticate with 802.1x & Radius. So configured an external Radius server (Imprivata) and configured the 2504 Radius options for the extenal server.( Layer 2: WPA2-AES & Auth Key Mgmt: 802.1x )
When I connect a client to this wireless, the authentication fails, I wonder whether it is because of the client side settings..
Which trusted Root Certification Authorities need to be checked?
Every time I power down my WLC2504 controller and then back up, the time reverts back to the year 2000.The APs can't join the controller, due to certificate errors, until I reset the clock. This problem just started recently.
View 6 Replies View Relatedhow can i replace my wlc2504 to a WLC5508 without disconnecting everybody, i have 3 SSID, on different VLAN.. I want the WLC5508 to be the main WLC, so i can remove the 2504 from the network. On the WLC5508, it will be the same configuration of the 2504. Is there a procedure or a wiki on such operation?
View 8 Replies View RelatedCan we change the internal web authentication for guest network to use http instead of https?
View 3 Replies View RelatedI would like to setup a 2504 to have one Guest WLAN and one Staff WLAN with a controller port for each WLAN connected to different devices.
I would prefer to connect the WLC Guest port to an ASA 5510 and the WLC Staff port to an internal 2960S switch. Will this work? I haven't setup a 2500 series controller previously.
I've set up a WLC2504 with interface "mgmt" and "guest" (2 different VLAN IDs) both configured on port1.Now I'd like to be able to connect to PoE ports (port 3 and 4) 2 LAPs which should be able to get IP addresses from the DHCP as if they were connected to port1.
View 14 Replies View Relatedsetting up a 2504 on a 2960 switch. The management interface is up and pingable, and from the WLC we can ping vlan 20 (our wireless client vlan) gateway. However, when we create the vlan20 interface on the WLC, give it a valid address and assign it to a port, we can no longer ping the vlan 20 gateway from the wlc, nor can we ping the vlan20 interface from a PC. I’m told the 2960’s don’t do dot1q trunking…
View 6 Replies View RelatedWhat's the difference between VPN Plus license and Security Plus license. I have new 5520 shipped with VPN Plus license.Also does it require a seperate license for Anyconnect for Mobile and AnyConnect Essentials.
View 1 Replies View RelatedI’m stuck in some problem with installation of LMS4.0 in customer site.
- we purchase a LMS4.0(CWLMS-4.0-100-K9) but couldn’t install it on Windows server 2008 R2 64bit because those things don’t support each other.
- I need to upgrade the LMS4.0 to LMS4.2 that is supporting Windows server 2008 R2 64bit.
- So, I ordered following items via product update tool (url...) [code]
- In this status, how to install LMS4.2 with license for 100 devices? If I install R-PI12-BASE-K9 first, can i enter a licese for 100 devices for CWLMS-4.0-100-K9 into PI1.2?
I got a set of dhcp pool in one 3750 attached to diferent Vlans in the network, the wired network works fine, you can get from any switch port across the LAN a diferente VLANs IP. In my wlc2504 I got 5 WLANs with the DHCP server pointed to the VLAN in the 3750, but I just got one set of ip when i tried to connect to diferent WLAN, without connectivity, I can see all the Ap's, and ping the VLANs in the 3750,
View 4 Replies View RelatedI have a question about managing the Access Point:
-WLC2504
-AIR-LAP1262N-A-K9
First: I need the access point works by period, example: 08:00AM - 06:00PM after that disable the radio and return work next day at 08:00AM
Second: Also, if the radio no activity for a long period (e.g 60 or 120 minutes), disable the radio interface.It's possible with the WLC? Or maybe need implement one NCS?EnergyWise Technology - but, I only need "shutdown" the radio not the Access Point completely.
can wireless router support up to 100 user including support network printer
View 1 Replies View RelatedOne of our clients is going to install WCS on a Vmware machine and uninstall it from the physical server. He wants to know if he can use the same license or get another one; since he will get a new Mac address with the new VmWare machine.
View 1 Replies View RelatedIs it possible to have a license loaded on an AIR-CT5508-HA-K9 in order to have it working as a stand alone controller?
View 4 Replies View RelatedI have WLC 5508 with 12aps license, i will buy a new license with 50 Aps, my question, its possible add new license with 50 aps, totaling 62 aps licenses?
View 7 Replies View Related5508 W LAN controller with 50 AP License upgrade from 7.0.220 to 7.4 is it will effect to the license and configuration? Because the license came pre- installed.
View 1 Replies View RelatedI recently bought a Cisco 5508 WLC with SWC5500LPE-K9-70 and a Cisco 1262 AP with AIR-OPT60-DHCP vender class identifier .How can I check wether the SWC5500LPE-K9-70 is included on the 5508 wlc and AIR-OPT60-DHCP on the 1262 ap?
View 5 Replies View RelatedI cannot for the life of me get the license file to upload. I purchased 25 more licenses. Download and install tftp and put the license file in C:Program FilesTftpd64 But no matter what path I put in Mangagment>Software Activation>Commands, it fails.
View 9 Replies View Relatedtell me when is available for order the High Availability for AIR-CT2504, like:
AIR-CT7510-HA-K9 Cisco 7500 Series High Availability Wireless Controller
AIR-CT5508-HA-K9 Cisco 5508 Series Wireless Controller for High Availability
I'm looking for getting a Cisco prime NCS appliance (PRIME-NCS-APL-K9). I'm a little bit confused regarding to the license scheme:
1. Does the appliance has any license coming with it or we need to order the license separately?
2. If I have an WLC 5508 (license support 12 APs) & 12 3500 APs, then number of devices counted will be 1 (WLC) or 12 (APs) or 13 (WLC + APs) ?
I got a ISE 3315 with an IP-Plus license on it. Now I need to install a Wireless advanced license, but I got an error when trying. I've read that the wireless license doesn't need the ip-base one but I can't remove it?
View 1 Replies View RelatedBasically I need to upgrade the license for Base-AP count to add 100 more AP's however my vendor has provided hardcopy of license as below:
-LIC-CT5508-UPG
-AIR-CAS-3KC-K9
-AIR-WIPS-AP-5
-L-NCS-1.0-100-ADD
My understanding is rigister LIC-CT5508-UPG/PAK number on cisco site and get .lic file however what is the use of other PAK where do i register this files with? Moreover , we do have NCS , MSE in place which is centralised devices.