I cannot for the life of me get the license file to upload. I purchased 25 more licenses. Download and install tftp and put the license file in C:Program FilesTftpd64 But no matter what path I put in Mangagment>Software Activation>Commands, it fails.
View 9 RepliesI currently have a single 2504 Controller managing 50 AP's. I am adding a Second 2504 AP Controller with 15 Lic to manage an additional 10 AP's. My current 2504 has each port configured for my four subnets that and it is managing AP's in 4 buildings. Should I configure the new 2504 the same way so that it can see all four sites? All so if the main 2504 goes down can the second 2504 take over even thou we will be out of lic?
View 7 Replies View RelatedI have WLC 5508 with 12aps license, i will buy a new license with 50 Aps, my question, its possible add new license with 50 aps, totaling 62 aps licenses?
View 7 Replies View Relatedtell me when is available for order the High Availability for AIR-CT2504, like:
AIR-CT7510-HA-K9 Cisco 7500 Series High Availability Wireless Controller
AIR-CT5508-HA-K9 Cisco 5508 Series Wireless Controller for High Availability
I have a WLC 2504 with 5 AP licenses for which I have installed an adder license via GUI. The installation completed successfully, but I still cannot view the new license. The maximum number of APs is still showing as 5 and in fact I cannot add more that 5 APs. I tried installing the license file again, but now I get a "duplicate" error.
View 4 Replies View RelatedBasically I need to upgrade the license for Base-AP count to add 100 more AP's however my vendor has provided hardcopy of license as below:
-LIC-CT5508-UPG
-AIR-CAS-3KC-K9
-AIR-WIPS-AP-5
-L-NCS-1.0-100-ADD
My understanding is rigister LIC-CT5508-UPG/PAK number on cisco site and get .lic file however what is the use of other PAK where do i register this files with? Moreover , we do have NCS , MSE in place which is centralised devices.
rececntly we have installed 2504 WLC in of branch office, I can able to log via console but it is not coming over LAN not even showing in CDP, all config seems to be fine in wired side & WLC side & physical connection also fine...LED also green.I am seeing log message in WLC, is this related to License issue
View 2 Replies View RelatedI'm tring to setup a DMZ for a guest wireless off of a 5505. So this device has a base license. It has vlan1 and vlan 2 for inside and outside.Another vlan is configured to be a failover for the currently active wan connection. It is using the "no forward interface" command.Can I add another vlan as a DMZ if I use the "no forward interface" command? [code]
View 6 Replies View RelatedWe recently upgraded a ASA 5505 with the security plus license to allow us to add a second subnet, but are having a few problems configuring the second subnet. The original subnet we have configured 10.1.1.0 is able to access the internet without any problems. However the new subnet 10.1.5.0 is unable to access the internet and when we ran a trace packet the nat config nat (inside) 1 0.0.0.0 0.0.0.0 is showing as the rule that drops the packet.
Additionally we have not been able to get the 2 subnets to talk to each other even though same-security-traffic permit inter-interface is configured. How to configure the subnet 10.1.5.0 to access the internet or to get the subnets to communicate. Below is a streamlined version of our current config.
!interface Vlan1nameif insidesecurity-level 100ip address 10.1.1.1 255.255.255.0 ospf cost 10!interface Vlan2nameif outsidesecurity-level 0ip address 66.66.66.66 255.255.255.240 ospf cost 10!interface Vlan13nameif corporatesecurity-level 100ip
[Code].....
I recently set up a an external hard drive as a UPnP media server through my router. My media devices and my computer can see the drive fine. My question is, what is the best way to add files to the drive? It seems like a hassle to plug it into a computer directly every time I want to add more files, and FTP is kind of clunky. Is there any sort of software I can put on the drive or any better way to drop files onto it?I'm using a Seagate 2TB USB Drive formatted as FAT32 connected to a lemonade-equipped Westell 7501 router. I understand that it may be that I'm trying to get too high tech with my $7 router, but it seems that there should be a better solution.
View 2 Replies View RelatedWhat's the difference between VPN Plus license and Security Plus license. I have new 5520 shipped with VPN Plus license.Also does it require a seperate license for Anyconnect for Mobile and AnyConnect Essentials.
View 1 Replies View RelatedI’m stuck in some problem with installation of LMS4.0 in customer site.
- we purchase a LMS4.0(CWLMS-4.0-100-K9) but couldn’t install it on Windows server 2008 R2 64bit because those things don’t support each other.
- I need to upgrade the LMS4.0 to LMS4.2 that is supporting Windows server 2008 R2 64bit.
- So, I ordered following items via product update tool (url...) [code]
- In this status, how to install LMS4.2 with license for 100 devices? If I install R-PI12-BASE-K9 first, can i enter a licese for 100 devices for CWLMS-4.0-100-K9 into PI1.2?
I have a server connected to my router with a CAT5. I usually manage the server from my laptop connected to the router via WLAN. I often need to add files to a public folder on the server so it can be dowloaded by my clients when they need them. I can access my personal laptop from the server, but I cannot access the server's files from my laptop. This is recent and used to work fine. I also cannot acces other personal computers on my network that I often connect to
View 11 Replies View RelatedWhy a 2504 Poe? If it can not be used for AP.
View 10 Replies View RelatedI'm planning to upgrade our WLC 2504 from 7.2.111.3 to 7.4.100.0 but the cisco site says "WLC Version 7.4.100.0 will need Prime Infrastructure Version 1.3 to be managed, Version 1.3 is not yet available to download at this point of time" Is it something about NCS? we have only 1 cisco WLC 2504 and 6 1142APs.. Also let me know is it possible to go directly from 7.2 to 7.4 ?
View 8 Replies View Relatedwhat is the maximum number of APs supported on Cisco 2504 WLC?According to the Data Sheet it is 75:
[URL]
But according to the config guide it is 50:
[URL]
I believe the correct number is 50, but I just want to be sure.Is this a software limitation?
I've problem with a WLC 2504. Some Clients like phones and Thin Clients get an IP 0.0.0.0.Software Version is 7.0.235.0. Test with a Laptop seams to be OK. Some printers also got an 0.0.0.0.Around 30% are not OK. also had the log: Impersonation of AP with Base Radio MAC 00:yy:yy:yy:yy:yyusing source address of 00:xx:xx:xx:xx:xx has been detected by the AP with MAC Address: 00:yy:yy:yy:yy:yy on its 802.11b/g radio whose slot ID is 0 The problem is, I cannot go to 7.2 version because I have 2 x AP 1231 and 2 x 1242 AP's.1231 AP's are not anymore supported in 7.2 Version.
View 14 Replies View RelatedI have two WLC 2504 controllers. These controllers are for two different buildings. But they share a VLAN, and network address range. How can I control the access points to the register selected only at a specific controller.
Example:
AP 1 -> WLC 1
AP 2 -> WLC 2
AP 3 -> WLC 1
Since the buildings also broadcast in different SSID. The two controllers are in a mobility group.
If we update our ios on WLC do we have to add the certificate for AP's again or we don't need to do that.
View 4 Replies View RelatedSome time ago I updated a WLC, model 2504, from version 7.3 to 7.4.100.0. I also update the FUS (Field Upgrade Software) to the latest release, 1.8.0.0. Now I need to downgrade the WLC back to 7.3 version.
My doubt is: Can I just take the normal processes and downgrade the WLC back to 7.3, even with the FUS in version 1.8.0.0?
I'm new in installing WIFI, I have WLC 2504 using 7.4.100.0. I have AP 1600 (AIR-CAP1602E-E-K9)
I installed the WLC and AP in a cisco poe switch, wlc and ap are in the same subnet and can ping ap from WLC, but the AP cannot join the wlc. i have this error message
(Cisco Controller) >show ap join stats detailed 00:06:f6:d6:03:f0
Sync phase statistics
- Time at sync request received............................ Not applicable
- Time at sync completed................................... Not applicable
I have a problem in join my ap1130ag in my wlc 2504 i activate dhcp internel (172.19.1.50 ----> 172.19.1.60) in wlc and this wlc affected address for ap1130ag (172.19.1.51) wlc and ap1130ag is connected with switch 2960 (port 17,18) this port the switche is configured in trunk mod allowed all vlan then my wlc not detected ap1130ag?
View 4 Replies View RelatedI've got a 1524 ap and it wont join my 2540 WLC. The messages I see in the WLC is RADIUS authorization is pending for the AP. I've added the MAC address of the ap under AP Policies using MIC. I dont have a radius server either so not sure how to tackle this one.When I run debug capwap events enale under the wlc I see the following messages:Discarding discovery request in LWAPP from AP supporting CAPWAP.
View 35 Replies View RelatedWe have a 2504 on version 7.2.103.0 and 15 of the 1131 AG's.In short we cannot get the access points to register against the WLC, they seem to be caught up in a boot loop. They are seen on the WLC with a status of downloading, then once they have downloaded (Seen via CLI) I get an error message things I can confirm are The Country code is set to GB All ports are in Native VLAN Access points are ETSI type. It stops and restarts at syslog output DTLS-3-BAD-RECORD: Erroneous record recieved from x.x.x.x: Duplicate (replayed) record.
View 26 Replies View RelatedCan a 2504 WLC on a remote site provide guest access on one SSID, drop taht out locally on that site and provide corporate access on a second WLC that it then tunnls to a 5508 at the main corporate site ?
View 4 Replies View Relatedupgrade on the wireless controller 2504 from 7.0 to 7.4 is direct upgrade.My customer faced problem by upgrading the software 7.0 to 7.4 directly and the image hang.how should proceed recover the image 7.4/
View 7 Replies View RelatedI would like to get it clarified, that Cisco WLC 2504 running the code ( 7.2.110.0 ) does support IPv6 or not ?
From Cisco Documents they are asking to enable IPv6 support under WLAN > Edit Page, and Enabling mulicast on Ethernet Multicast Mode under Controller > General.
But from the GUI am not able to find the above two field, Even in Interface i created under Controller > interface is not accepting IPv6 address. I am able to configure IPv6 ACL .
Is any deployment document is available to show different scenarios with configuration.
Note - Am using Access point AIR-LAP1262N-N-k9
Currently I am using WLC 2504 with Software version 7.0.220.0. I am having some issues with Windows 8 clients they can't connect and I read on couple of review that wlc needs upgrade software.
I checked and latest versin is 7.4. Can I go to this version directly or I have to jump step by step.
I am trying to TFTP an image to a Cisco 2504 WLC. The management interface is 10.1.1.1 /24 and I have my PC connected to a port on the WLC with the IP address 10.1.1.10. However, I still do not have connectivity between the PC and WLC.
View 3 Replies View RelatedI am about to deploy a load of Aironet LWAPs into my organization. I've configured the WLC 2504 and have a couple of the APs working at our main site. I just needed to plug them in, and they worked perfectly, straight out the box. But I just want to know the following:
1 - will the same apply if I connect an AP at a remote site? Remote sites are on different subnets and connected via IPSEC. Will the remote APs just find the WLC?
2 - is there anything I need to set up especially on the WLC in order to make this work?
3 - what happens if the IPSEC connection drops?
My customer is seeing these Errors coming up on one of his 2504 WLC's (ver7.3) The MAC's and IP addresses Mentioned seem to be completely fictitious as the customers IP plan is way off these subnets and the vendor lookup tool cant resolve the MAC addresses.I can confirm that there is no conflict.I've seen them appear on other 2504's across his network on seperate occasions.
View 4 Replies View RelatedI have a 2504 WLC and 1042 ap's. Everything worked great in my test enviroment (of course). Now when I want to deploy the wireless, the ap's are not getting and ip for the windows dhcp server.
I have option 43 configured in dhcp, sub option 241>ip address of the controller
I have my A record in dns, cisco-capwap-controller.
*Mar 1 00:03:17.050: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
Not in Bound state.
*Mar 1 00:03:27.050: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:27.054: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:03:37.054: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:47.054: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:57.054: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:04:07.054: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
Not in Bound state.
We have a WLC 2504, since a few months, it was working fine, we have a guest Wlan configure with web authentication and the DHCP scope for this in the WLC. The problem today is that its no redirecting the web browser to 1.1.1.1, we try it with 3 laptops and they recieve a correct IP from the DHCP but still can not get redirect to the web authentication portal. Have the default configuration Internal (Default).
In laptops we check the firewall, dont have a proxy activate and have google DNS.. 4.2.2.2 8.8.8.8. In fact this laptops connected to this ssid before.