Cisco Wireless :: 2504 - AP Not Getting IP For DHCP Server
May 21, 2013
I have a 2504 WLC and 1042 ap's. Everything worked great in my test enviroment (of course). Now when I want to deploy the wireless, the ap's are not getting and ip for the windows dhcp server.
I have option 43 configured in dhcp, sub option 241>ip address of the controller
I have my A record in dns, cisco-capwap-controller.
*Mar 1 00:03:17.050: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
Not in Bound state.
*Mar 1 00:03:27.050: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:27.054: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:03:37.054: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:47.054: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:57.054: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:04:07.054: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
Not in Bound state.
View 3 Replies
ADVERTISEMENT
Mar 25, 2013
setup a DHCP server on a WLC 2504. I'll try to resume my configuration:
I have 2 networks: inside users (vlan 1) and external users (vlan)
My controller uses the port 1 to connect to the switch, which has a trunk with WLC.
I have two routers, one using vlan 1 (192.168.3.0/24) and one using vlan 10 (200.X.X.X). All ports to these routers are access ports on their respective vlans.
I have 2 SSID, one for inside, other to outside. Inside is working very well.
To the outside I created a DHCP escope and already set the IP of the management interface 192.168.3.119.
Managemente interface (vlan 1 inside): 192.168.3.119/24
Outside interface (vlan 10): 200.X.X.195 - Default gateway 200.X.X.X.193
I alredy checked the DHCP Proxy in Advanced option.
See the output of the debug client:
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >
[Code].....
View 3 Replies
View Related
May 29, 2012
Is it possible to assign IP addresses to remote site WIFI users from local DHCP server and forward all other traffic to 2504 WLC?
[WIFI Users] >--------<AP (DHCP server) >------ VPN ---------< WLC
View 1 Replies
View Related
Nov 25, 2012
I am wondering if the folowing is a valid configuration:
WLC2504
AP2600
I need 3 SSID/VLAN, 1 for corporate devices, 1 for coporate smartphones, 1 for guest.
Port 1 on the 2504 should be used for management and corporate devices and connect to the corp network. Port 2 is for smartphones/guest and will be connected to a Cisco ASA 5515 that is connected to a second ISP.
Corp devices should get IP from an Windows DHCP. Smartphones/guest should get IP from the WLC. Is this possilbe? I read this in a document "To use the WLC as a dhcp, you need to enable DHCP proxy as it is required." Some how I am imagining that this will mess with the Windows DHCP. Is it better to use the ASA as DHCP for smartphones/guest?
View 4 Replies
View Related
Aug 25, 2012
i have configured wlc 2504 .in that i have configured two interfaces.one is guest, 2nd is internal user, the pblm when user try to connect with that contain ssid user not getting ip address,
i have connected only one link between core to wlc on port 1.for guest interface i used port 4.but no physical link.
View 3 Replies
View Related
Aug 8, 2012
My problem, in a nutshell, is that clients do not get an IP from an external DHCP server when connected to a guest VLAN.
My current setup is:
Native VLAN 1 (192.168.2.x)
2008 DHCP Servers
2504 WLC
[Code].....
The guest WLAN just uses WPA and a PSK and is set to interface vlan101 There rest of the 2504 config is default.
The ports that the WLC and APs are connected to are tagged on the correct VLANs. (is that even necessary for the AP now?)
Ive changed the interface config around a hundred times now with no luck. No matter what a client will not get an IP.
Could this be due to the 2504 and ASA both acting as DHCP relays? Ive tried setting the IP of the DHCP on the dynamic interface to many different things with no luck.
View 10 Replies
View Related
Jan 7, 2013
I have a Cisco Wlan Controller 2504 with 1042N AP (3-nos) every thing was working fine from past 2 months. Now i am getting a issue with clients which are connected to the wireless AP, they are not able to get an dhcp IP address from the 2960 Switch (DHCP Server). The clients are getting IP address as 0.0.0.0. [code]
View 36 Replies
View Related
Apr 17, 2013
I am looking to enable the internal DHCP on my WLC. I have enabled it and it seems to be operating correctly but I think my routing and or settings allowing me to access anything beyond the private network is wrong.
DHCP is handing out correct IP info and DNS info.How do I route the new private network (10.1.9.*) out to our existing 10.1.4.1. (management IP is 10.1.4.253) Can this be done within the WLC ?
View 3 Replies
View Related
Nov 7, 2012
All controllers are in version 7.2.111.3.C1 is a 5508, it is ou anchor controller.C2 is a 5508, it is a big site controller.C3 is a 2504, it is a small site controller. C2 and C3 are in the same mobility group than C1 (and all is up up in mobilty managment). When "DHCP Addr. Assignment" is enable on C1 : Clients on C2 received their IP address by our external DHCP server via C1 and the guest tunneling betwenn C1 and C2 and all is working fine. Clients on C3 don't received their IP address by our external DHCP server via C1 and the guest tunneling betwenn C1 and C3, so nothing work.
View 4 Replies
View Related
Apr 17, 2013
I am looking to enable the internal DHCP on my WLC. I have enabled it and it seems to be operating correctly but I think my routing and or settings allowing me to access anything beyond the private network is wrong.
DHCP is handing out correct IP info and DNS info. How do I route the new private network (10.1.9.*) out to our existing 10.1.4.1. (management IP is 10.1.4.253) Can this be done within the WLC ?
View 3 Replies
View Related
Apr 2, 2013
I have just setup a new WLC 2504 controller to manage a WiFi service that will span 6 geographic locations. The local networks at each location are on different subnets (all 192.168.x.x) and are linked up via IPSEC VPN links, and there is Active Directory spanning the sites, with DNS and DHCP servers running at each location.
I tested the WLC at our main office with a single AP, and it worked fine. The AP set itself up, and wireless devices connect with no probs. Great! Yesterday I headed out to one of our remote sites, and connected an AP to their network - and that seemed to work fine too. Within a few minutes I was able to see the WiFi network I'd setup, and my smartphone connected to it straight away (as I'd rpeviously connected at the main office), so I was pretty happy that all was working well.
This morning however I've had notification that wifi performance at the remote site isn't great. I've got someone to check their ip address, and I've found that their IP address and default gateway match the LAN at the main office where the WLC is based - NOT the LAN where the wireless client is. Obvioulsy this is not ideal!
(I guess I HAVE done something wrong!?). And how can I get wireless clients at remote sites to pick up an IP from the DHCP server at THEIR site?
View 3 Replies
View Related
Jul 12, 2012
I want to know if its nessary to install Certificate authority on your radius server. If we have a CA server already in the domain can we use that for this purpose or we have to install certificate authority on our DC.
View 1 Replies
View Related
Apr 15, 2013
I have a customer who has 2 NCS servers; 1 residing at their corporate site and the other residing at their local site. They have a WLC2504 controller at the local site. They would like to connect both ncs servers to to the local WLC. Is it possible to connect 2 ncs servers to a single controller? Can WLC configuration databases on two different NCSs be the same? How can you prevent 1 NCS from overwritting the other?
View 5 Replies
View Related
Oct 30, 2012
Ok, so with my WLC2504 implementation, I use the 4 ports to physically segment my wireless networks. Here is my setup:
Port 1 (Management) - Internal IP so I can manage the WLC from our internal network (Untagged)
Port 2 - Connected to our core stack and tagged with VLAN 14
Port 1 and 2 are both connected to the same core stack
Port 3 - Connected to a RV016 Linksys which is connected to our fiber connection to the outside (Untagged) - External connection for laptops
Port 4 - Connected to a Linksys wireless router (with wireless disabled) (Untagged) - External connection for smartphones
The TAC engineer I talked to just told me that I can only have one untagged interface on the WLC. If they are physically connected to different switches, thus physically segmenting the network, should it matter?
The wireless works just fine. What I am having issues with is getting a client that is hard-wire connected to the RV016 to get a DHCP address from the WLC.
View 9 Replies
View Related
Apr 14, 2013
I have two ethernet cards (from same equipment) that arent acquiring IP Address after instalation of WLC 2504.I dont want (yet) to disable DHCP proxy on WLC.
*DHCP Socket Task: Apr 15 18:49:04.219: 00:0a:95:XX DHCP received op BOOTREQUEST (1) (len 556,vlan 0, port 1, encap 0xec00)
*DHCP Socket Task: Apr 15 18:49:04.219: 00:0a:95:XX DHCP dropping packet (no mscb) found - (giaddr 0.0.0.0, pktInfo->srcPort 68, op: 'BOOTREQUEST')
*DHCP Socket Task: Apr 15 18:49:07.218: 00:0a:95:XX DHCP received op BOOTREQUEST (1) (len 556,vlan 0, port 1, encap 0xec00)
*DHCP Socket Task: Apr 15 18:49:07.218: 00:0a:95:XX DHCP dropping packet (no mscb) found - (giaddr 0.0.0.0, pktInfo->srcPort 68, op: 'BOOTREQUEST')
[code].....
View 6 Replies
View Related
Aug 13, 2012
I need to integrate a 2504 WLC with a windows 2003 LDAP server for extented authentication, is there any guides available for this ?
View 1 Replies
View Related
Mar 6, 2013
Can the 2504 WLC be configured to work with one RADIUS Server for Authentication of Management Users and with a second server for 802.1x EAP-TLS certificate authentication for the end users.
Management Users will authenticate on RADIUS Server 1.Wireless End users will request 802.1x EAP-TLS authentication certificate from AAA server 2.
View 5 Replies
View Related
Sep 29, 2011
i am facing the same problem now but am using windows 2003 server
View 1 Replies
View Related
May 6, 2012
[code]...
I am able to obtain IP addresses through the DHCP server for my clients and I am able to browse internet on the server 2k8.Server 2008 - Share Internet through DHCP server
View 10 Replies
View Related
Apr 22, 2012
I have Internal DHCP Server configured on the Cisco WLC 5508 and all is working fine. DHCP Range is 192.168.1.100 to 192.168.1.245. Now I created another SSID but I want clients connecting to this SSID get specific IP's or from a specific range. WLC has no option to bind a DHCP pool to a specific IP so what I did I checked the option to "Override DHCP" and added the IP of my firewall WLC is connected to and setup a DHCP Pool on that firewall as 192.168.1.89 to 192.168.1.94 (192.168.1.88/29).
Client can connect to the second SSID but can't grab and IP address, what am I missing ?
View 6 Replies
View Related
Apr 10, 2013
Recently I came across a wireless design whcih I ws not able to understand.The design is:
1. Two wireless LAN Controllers 5508, each with 25 AP license. AP load (5APs per Contorller) shared between the WLCs and congured with Backup Controller option.
2. The design has a Data Center Switch 3560x series, on which the two WLCs, Cisco Prime Infrastructure and Cisco MSE were connected. I've attached the design here.
3. The Data Center Switch is configured with DHCP pool for the wireless clients. The IP Address of the Data Center Switch is : 10.xx.xx.2 and Default Gateway is: 10.xx.xx.1
4. On the WLC, the Management Interface is configured with the IP Address: 10.xx.xx.21 for Controller 1 adnd 10.xx.xx.22 for Controller 2. But, their DHCP Server is configured with IP Address: 10.xx.xx.1 but not with 10.xx.xx.2 .
This means, all the DHCP requests are pointing towards the Gateway of the Data Center Switch.Is this the correct configuration?I have seen the Wireless Clients getting the IPs allocated from the DHCP Pool, even though the Management Interface's DHCP server configured with Gateway IP address 10.xx.xx.1 .
The DHCP configuration for the Data Center Switch is:
ip dhcp pool xxxxxx
network 10.164.220.0 255.255.254.0
default-router 10.164.220.1
The Management Interface configuration on the WLC is:
Interface Configuration
Interface Name................................... management
MAC Address...................................... 2c:54:2d:72:b5:40
IP Address....................................... 10.164.220.21
IP Netmask....................................... 255.255.254.0
IP Gateway....................................... 10.164.220.1
External NAT IP State............................ Disabled
[code]....
View 2 Replies
View Related
Mar 7, 2012
I have configurate AP1230 as DHCP server. And I have 2 vlan and SSID :
vlan 1: office use
SSID: OFFICE
vlan 11: guest use
SSID: GUEST
Now the user can login with OFFICE's ssid for obtain IP from windows server 192.168.3.4. But GUEST's ssid can't obtain IP after login.
ip subnet-zero
ip dhcp excluded-address 10.0.0.1 10.0.0.20
ip dhcp excluded-address 10.0.0.40 10.0.0.254
[Code].....
View 9 Replies
View Related
Apr 17, 2012
I have successfully implemented wireless guest access using 4402 WLC as the Anchor and 5508 as Foreign. The Anchor controller also provides dhcp services to guest clients. The 5508 is LAGged and there is no issue with the guests traffic separated from corporate. At a remote site, there is a 4402 WLC using LAG and also acting as a Foreign controller. But when a client connects to the guest WLAN, it obtains a corporate dhcp address instead of the dhcp address assigned from the Anchor controller. The guest WLAN setting is the same as with the 5508 controller i.e. DHCP server override is ticked and the management IP address of the Anchor controller is specfied. Also DHCP Addr required is ticked. Why the 4400 controller is not forwarding dhcp requests to the anchor controller and instead sending to the corporate dhcp server.
View 36 Replies
View Related
Feb 1, 2012
Is it problem with iPads or LAP1141n?WLC 4404 and many 1142 and 1141, so other devices laptops, iphones, androind phone works as well.But iPad authorized, but can't get an ip address from dhcp server (dhcp not local on wlc, on windows machine) with coverage lap1141, but it get ip with coverage lap1142, and when i got it i roaming to lap1141 and it stays, if i off/on iPads can't get it again from lap1141.
View 14 Replies
View Related
Apr 26, 2013
If I set a primary DHCP server in the interface configuration, or if I override DHCP in the WLAN Configuration.Which interface does the WLC use to try and connect to the DHCP on behalf of the wireless clients?IFA) The dhcp server is not on any of the configured subnets.B) The DHCP server is on a different interface's subnet.
View 4 Replies
View Related
May 7, 2012
I am hoping to get your feedback around the dhcp issues I am facing with Two Centrally Switched Wireless LANs. The setup is as follows:
- I have a WLC 5508 which has been configured with 4 SSIDs, out of which 2 are using Central Authentication and Switching. - I have an LWAP connected to the WLC in HREAP mode. - WLC is configured as the DHCP server for clients connecting to the SSID 'Guest'. For the rest, I am using external dhcp server. - Only one scope for Guest Interface is setup on the WLC.
Problems:
1. As far as I know, for WLC to act as internal dhcp server, it is mandatory to have the proxy enabled, but the Clients connecting to SSID 'Internet' are unable to get an ip address from the external dhcp server, if dhcp proxy is enabled on the WLC. If i disable the proxy, it all works fine.
2. DHCP does not release the ip addresses assigned to clients even after they are logged out.
3. If a machine which was earlier connected to 'Guest' SSID connects to the 'Internet' SSID, it requests the same ip it was assigned by the WLC which it was assigned under 'Guest', but gets tagged with the V LAN configured on the management interface.
************Output from the Controller********************
(Cisco Controller) >show sysinfo
Manufacturer's Name............. Cisco Systems Inc.Product Name................ Cisco Controller Product Version................. 7.0.116.0Bootloader Version................ 1.0.1Field Recovery Image Version..................... 6.0.182.0Firmware Version..... FPGA 1.3, Env 1.6, USB console 1.27Build Type.......... DATA + WPS + LDPE
[code]...
View 12 Replies
View Related
Jul 21, 2012
A client wants us to use the internal DHCP server on a 5508 instead of Windows DHCP. They will have 15 APs initially and upto 25 later. The docs on the 7.2 WLC make it sound like this is discouraged: Internal DHCP Server.
The controllers contain an internal DHCP server. This server is typically used in branch offices that do not already have a DHCP server. The wireless network generally contains 10 access points or fewer, with the access points on the same IP subnet as the controller.
In this case, the APs will not be in the same subnet as the Managment Internet.Is it a mistake to use the internal DHCP with upto 25 APs (3 WLANs)?
View 3 Replies
View Related
Jan 16, 2013
I have a 4402 (version 7.0.235) working with 10 units of 1121 APs connected to it. The WLC is not configured to work in LAG mode. Physical portt #1 is connected to the Main Switch (trunk). I have 3 WLAN mapped to 3 Different VLAN and Everything (security and internal, external DHCP) is working swell...Now- I have connected Physical port #2 directly to an ADSL Router (giga port), Configured Port 2 as untaggedwith the proper IP details.I have configured this interface to receive DHCP from the ADSL Router and for some reason, Clients are not getting addresses.When I assign a Static address to my laptop I get internet access and all is nice. I tried configuring The WLC internal DHCP server (instead of the ADSL router) and that didn't work. It seems like a DHCP problem but I dont understand the source of the problem of think of the solution.When turning off the proxy settings I noticed that it worked. Is there anything to do with that? The problem was that after a while the other WLANs starting causing DHCP issues as well.
View 7 Replies
View Related
Feb 15, 2012
I have a Linksys WAP200 Wireless-G Access Point problem. It is SW version 2.0.4.0. I have it configured for a small network and the problem seems to be that it is not forwarding DHCP requests onto my DHCP server. I know that it is not a SSID or Key issue as when I give my devices static IP addresses, they communicate fine within my system. The only issue seems to be when the devices make DHCP client requests. I also know that the problem is not my DHCP server as it has the device's IP / mac addresses in its configuration file and other wired devices are able to communicate with it to get their IP address through DHCP.
I have seen that there was talk in some blogs about WAP200 no forwarding DHCP requests and I was hoping that updating the device to the latest release would have resolved the problems.
View 3 Replies
View Related
Jul 17, 2012
I configured DHCP pool on Cisco AP 1131, Laptop users are working fine and obtain IP address from AP 1131 DHCP Server, but IPad user is getting IP problem when he try to connect Cisco AP 1131.when i reboot the AP, IPad user getting IP address from 1131 AP dhcp server and access the network resource for the 2-3 hr after that IPad show "obtaining ip address from .....".
AP Detail-
AIR-AP1131AG-N-K9
c1130-k9w7-tar.124-10b.JA2
12.3(8)JEA
View 1 Replies
View Related
Apr 8, 2008
I am trying to setup a guest vlan. I set up an interface for the guest vlan on my 4402 controller. I assigned the guest vlan interface an IP of 192.168.2.10 with a 24 bit subnet mask.
This vlan will go to my DMZ where there is no DHCP server so I need to setup the internal DHCP server. I created a new scope but I'm having trouble with what to put in the Network field for the DHCP scope. The pool addresses are 192.168.2.100-200. with a 24 bit subnet mask.
Every time I try to apply the configuration I get an "error in setting DHCP scope network and netmask".
I've tried using:
192.168.2.10
192.168.2.255
192.168.2.254
as entries for the Network setting but no go. The docs say to enter the IP address used by the management interface with subnet mask applied.
I was assuming they meant the interface for the guest vlan.
View 3 Replies
View Related
Jan 12, 2012
How to clear dhcp lease in WLC 6.0.199 from the IP leased from internal server?
View 1 Replies
View Related
Jan 1, 2013
I have two WAP321s in my office. The network they are on is a single VLAN (172.16.10.x). Both WAPs are setup with the same SSID, and I have setup Single Point Setup.
I am having a problem that was happening before I setup Single Point Setup, and it is still happening. Basically wireless will be up and running fine for part of the day. Then people throughout the office will begin to lose their connections to the DHCP server. They still retain the connection to the WAP, but can no longer access the network.
The only way I have been able to fix this issue is to reboot the WAP. As soon as it reboots the connections come back. At first I thought it was due to the number of connections (which is why we now have 2 WAPs), however we only have about 20-25 conncurrent connections.
I put in the second WAP to try to balance out the load but this does not seem to be working. Is there a setting I need to change on the WAPs to balance out the load?
View 13 Replies
View Related
