I've got a 1524 ap and it wont join my 2540 WLC. The messages I see in the WLC is RADIUS authorization is pending for the AP. I've added the MAC address of the ap under AP Policies using MIC. I dont have a radius server either so not sure how to tackle this one.When I run debug capwap events enale under the wlc I see the following messages:Discarding discovery request in LWAPP from AP supporting CAPWAP.
View 35 Replies
Someone already do a bridge configuration with 1524 AP? I read Cisco documentation, and is not very clear regarding configuration on switch side.I will do a Bridge in trunking mode, so i want to know what is the VLAN i need to set as native vlan on the switch trunk port.Do i need to set the management vlan as native VLAN?
View 6 Replies View RelatedI am getting below error in our network which has access points 1524.
AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:b8:c9:c9:10:1c:40 Cause=Heartbeat Timeout Status:NA
As a result , the ap disassociates from the controller , then re-associates. However, it keeps going up & down in short spans.
I have multiple 1230AG wireless access point in autonomous mode that I am migrating to lightweight mode so that a 4402 controller can manage them. I already migrated 4 of those APs with no problems using the Upgrade Tool version 3.4 and now I have one that just refused to upgrade version.
I ran the upgrade tool for this AP alone with the same parameters as others. It is now on lightweight version 12.3.7-JX9 The upgrade procedure went smoothly, the SSC was created on the AP and added to the authorised list on the controller. The AP boots up, gets an IP by DHCP, tries the controller via DNS, gets to it. It joins it then disconnects. Its FastEthernet interface keeps doing down/up every 90 seconds or so.
In my controller logs I see:
*SNMPTask: Feb 22 19:39:17.135: %LWAPP-3-INVALID_SLOT: spam_api.c:711 Invalid slot identifier (0) - ; AP 00:13:.........
*spamReceiveTask: Feb 22 19:39:13.150: %LWAPP-3-PAYLOAD_MISSING:
[Code].....
Release 6 controller 9 Mesh APs. 1524 (2x 5G radios, 1x 2.4G) and 1522 (1x 5G radios, 1x 2.4G) Designed for 3 linear hops and then a split to the rest.
AP1 = Root AP
linear to
AP2
Linear to
AP3
Linear to
AP4
equidistant to
AP5 and AP6
The rest are further away from AP4, but have visibility back to AP 4 The issue is after an event (say a power outage) at AP4.AP5 uses AP3 as it's parent.That's okay during the power failure, but when AP4 comes back up, I want to force AP5 to switch it's parent to AP4.You may ask why, if AP5 can reach AP3 okay, it's okay to leave it that way.
test --------packet loss %-----
speed AP3toAP5 AP3toAP4 AP5-AP4
===== ======= ======= =======
54M 100 0 0
48M 100 0 0
36M 52.6 0 0
24M 1.44 0 0
18M 0.89 0 0
So you can see it's desireable now that AP5 uses AP4 as it's parent.Over time, the system might figure it out, but our limited experience shows it seems to stick to the way it is.To complicate matters, sometimes we've found that it doesn't seem to reconfigure when the channel number has changed so AP5 can reach AP3, but AP4 (1524) comes up with a different channel on it's downlink radio.So, how can we force a mesh topology reevaluation/change for either 1 AP or the whole bridge group?I thought changing the bridge speed from "auto" to 54M (on AP3 above, for example) might force the attached children to rethink it, but it didn't seem to work (maybe I needed to wait an hour?).I also thought tweaks to "Radio Performance Profile" for radio might work. (not sure what to change, or how long to wait for a result)reseting APs and hoping they come back in a better topology is painful and slow.
The following messages are filling up my syslog.
*spamApTask0: Nov 09 15:59:29.071: %LOG-3-Q_IND: capwap_ac_reassembly.c:652 Unable to store capwap fragment from 88:f0:77:b6:fd:00.
*spamApTask3: Nov 09 15:59:27.616: %CAPWAP-3-REASSEM_SPACE: capwap_ac_reassembly.c:652 Unable to store capwap fragment from 88:f0:77:b6:fd:00.
What could be causing it? I am using 1524 APs in a Mesh environment with a WLC 5508 (7.0.116.0) which is connected to a H3C switched network.
The MAC addresses above are from my MAPs and I don't think I am getting it from the RAPs.
I wonder if I can join via the WAP 4410n Bridge and also work as Access-point at a time. The idea is that you can connect to a router that provides Internet service that makes access-point bridge and connect to another WAP 4410n which would be another single access point for wireless bridge.
View 1 Replies View RelatedRARP (Reverse Address Resolution Protocol) is a protocol by which a physical machine in a local area network can request to learn its IP address from a gateway server's Address Resolution Protocol (ARP) table or cache. A network administrator creates a table in a local area network's gateway router that maps the physical machine (or Media Access Control - MAC address) addresses to corresponding Internet Protocol addresses.When a new machine is set up, its RARP client program requests from the RARP server on the router to be sent its IP address. Assuming that an entry has been set up in the router table, the RARP server will return the IP address to the machine which can store it for future use.Among the passage of words i read, there was this sentence i were not sure, "A network administrator creates a table in a local area network's gateway router that maps the physical machine (or Media Access Control - MAC address) addresses to corresponding Internet Protocol addresses." Does it means each time a host computer joins in the ethernet LAN, the network administrator would manually add in it's MAC address in the router table, so it would allow the newly joined computer to request IP address from it's MAC address?
View 1 Replies View RelatedMy ACS5.2 joined Windows 2003 Active Directory successfully. I created Support group with user1 in the internal store, also created Support-AD group with userad1 in the AD store. Identity Store Sequency is set Internal first, then AD. I can map Support-AD group to the local Support group without any problem.
Internal user gets authenticated and authorized OK. However, if the user is an AD user, the rule for AD users is not picked. So it goes to default.
I have a domain network , when i log on domain the internet is lost , and still did work until i to return this pc to workgroup without change any ip configuration , i try to resolve this and i found that when I rejoined to domain , it's work but not for long time only work until the pc rebooting ?
View 1 Replies View RelatedI've just updated the WiFi mini card in my Inspiron 1545. It works great.....but, I have to download the driver every time I start the laptop.
View 4 Replies View Relatedyour computer could not be joined to the domain because the following error has occured,access denied,this error is happening when i create users for active directory users and computers in windows server 2003,i have 11 computers ,,1 server and 10 clients,,i created 10 users in active directory users and computers ,,until here i have no problem,,but when i want join client computers with server it is happening this error(your computer could not be joined to the domain because the following error has occurred,access denied)i can join 3 client computer with the server in fourth computer it happening that error,what can i do?
View 9 Replies View RelatedWhy a 2504 Poe? If it can not be used for AP.
View 10 Replies View RelatedI'm planning to upgrade our WLC 2504 from 7.2.111.3 to 7.4.100.0 but the cisco site says "WLC Version 7.4.100.0 will need Prime Infrastructure Version 1.3 to be managed, Version 1.3 is not yet available to download at this point of time" Is it something about NCS? we have only 1 cisco WLC 2504 and 6 1142APs.. Also let me know is it possible to go directly from 7.2 to 7.4 ?
View 8 Replies View Relatedwhat is the maximum number of APs supported on Cisco 2504 WLC?According to the Data Sheet it is 75:
[URL]
But according to the config guide it is 50:
[URL]
I believe the correct number is 50, but I just want to be sure.Is this a software limitation?
I've problem with a WLC 2504. Some Clients like phones and Thin Clients get an IP 0.0.0.0.Software Version is 7.0.235.0. Test with a Laptop seams to be OK. Some printers also got an 0.0.0.0.Around 30% are not OK. also had the log: Impersonation of AP with Base Radio MAC 00:yy:yy:yy:yy:yyusing source address of 00:xx:xx:xx:xx:xx has been detected by the AP with MAC Address: 00:yy:yy:yy:yy:yy on its 802.11b/g radio whose slot ID is 0 The problem is, I cannot go to 7.2 version because I have 2 x AP 1231 and 2 x 1242 AP's.1231 AP's are not anymore supported in 7.2 Version.
View 14 Replies View RelatedI have two WLC 2504 controllers. These controllers are for two different buildings. But they share a VLAN, and network address range. How can I control the access points to the register selected only at a specific controller.
Example:
AP 1 -> WLC 1
AP 2 -> WLC 2
AP 3 -> WLC 1
Since the buildings also broadcast in different SSID. The two controllers are in a mobility group.
If we update our ios on WLC do we have to add the certificate for AP's again or we don't need to do that.
View 4 Replies View RelatedSome time ago I updated a WLC, model 2504, from version 7.3 to 7.4.100.0. I also update the FUS (Field Upgrade Software) to the latest release, 1.8.0.0. Now I need to downgrade the WLC back to 7.3 version.
My doubt is: Can I just take the normal processes and downgrade the WLC back to 7.3, even with the FUS in version 1.8.0.0?
I'm new in installing WIFI, I have WLC 2504 using 7.4.100.0. I have AP 1600 (AIR-CAP1602E-E-K9)
I installed the WLC and AP in a cisco poe switch, wlc and ap are in the same subnet and can ping ap from WLC, but the AP cannot join the wlc. i have this error message
(Cisco Controller) >show ap join stats detailed 00:06:f6:d6:03:f0
Sync phase statistics
- Time at sync request received............................ Not applicable
- Time at sync completed................................... Not applicable
I currently have a single 2504 Controller managing 50 AP's. I am adding a Second 2504 AP Controller with 15 Lic to manage an additional 10 AP's. My current 2504 has each port configured for my four subnets that and it is managing AP's in 4 buildings. Should I configure the new 2504 the same way so that it can see all four sites? All so if the main 2504 goes down can the second 2504 take over even thou we will be out of lic?
View 7 Replies View RelatedI have a problem in join my ap1130ag in my wlc 2504 i activate dhcp internel (172.19.1.50 ----> 172.19.1.60) in wlc and this wlc affected address for ap1130ag (172.19.1.51) wlc and ap1130ag is connected with switch 2960 (port 17,18) this port the switche is configured in trunk mod allowed all vlan then my wlc not detected ap1130ag?
View 4 Replies View RelatedWe have a 2504 on version 7.2.103.0 and 15 of the 1131 AG's.In short we cannot get the access points to register against the WLC, they seem to be caught up in a boot loop. They are seen on the WLC with a status of downloading, then once they have downloaded (Seen via CLI) I get an error message things I can confirm are The Country code is set to GB All ports are in Native VLAN Access points are ETSI type. It stops and restarts at syslog output DTLS-3-BAD-RECORD: Erroneous record recieved from x.x.x.x: Duplicate (replayed) record.
View 26 Replies View RelatedCan a 2504 WLC on a remote site provide guest access on one SSID, drop taht out locally on that site and provide corporate access on a second WLC that it then tunnls to a 5508 at the main corporate site ?
View 4 Replies View Relatedupgrade on the wireless controller 2504 from 7.0 to 7.4 is direct upgrade.My customer faced problem by upgrading the software 7.0 to 7.4 directly and the image hang.how should proceed recover the image 7.4/
View 7 Replies View RelatedI would like to get it clarified, that Cisco WLC 2504 running the code ( 7.2.110.0 ) does support IPv6 or not ?
From Cisco Documents they are asking to enable IPv6 support under WLAN > Edit Page, and Enabling mulicast on Ethernet Multicast Mode under Controller > General.
But from the GUI am not able to find the above two field, Even in Interface i created under Controller > interface is not accepting IPv6 address. I am able to configure IPv6 ACL .
Is any deployment document is available to show different scenarios with configuration.
Note - Am using Access point AIR-LAP1262N-N-k9
Currently I am using WLC 2504 with Software version 7.0.220.0. I am having some issues with Windows 8 clients they can't connect and I read on couple of review that wlc needs upgrade software.
I checked and latest versin is 7.4. Can I go to this version directly or I have to jump step by step.
I am trying to TFTP an image to a Cisco 2504 WLC. The management interface is 10.1.1.1 /24 and I have my PC connected to a port on the WLC with the IP address 10.1.1.10. However, I still do not have connectivity between the PC and WLC.
View 3 Replies View RelatedI am about to deploy a load of Aironet LWAPs into my organization. I've configured the WLC 2504 and have a couple of the APs working at our main site. I just needed to plug them in, and they worked perfectly, straight out the box. But I just want to know the following:
1 - will the same apply if I connect an AP at a remote site? Remote sites are on different subnets and connected via IPSEC. Will the remote APs just find the WLC?
2 - is there anything I need to set up especially on the WLC in order to make this work?
3 - what happens if the IPSEC connection drops?
My customer is seeing these Errors coming up on one of his 2504 WLC's (ver7.3) The MAC's and IP addresses Mentioned seem to be completely fictitious as the customers IP plan is way off these subnets and the vendor lookup tool cant resolve the MAC addresses.I can confirm that there is no conflict.I've seen them appear on other 2504's across his network on seperate occasions.
View 4 Replies View RelatedI have a 2504 WLC and 1042 ap's. Everything worked great in my test enviroment (of course). Now when I want to deploy the wireless, the ap's are not getting and ip for the windows dhcp server.
I have option 43 configured in dhcp, sub option 241>ip address of the controller
I have my A record in dns, cisco-capwap-controller.
*Mar 1 00:03:17.050: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
Not in Bound state.
*Mar 1 00:03:27.050: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:27.054: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:03:37.054: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:47.054: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:57.054: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:04:07.054: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
Not in Bound state.
We have a WLC 2504, since a few months, it was working fine, we have a guest Wlan configure with web authentication and the DHCP scope for this in the WLC. The problem today is that its no redirecting the web browser to 1.1.1.1, we try it with 3 laptops and they recieve a correct IP from the DHCP but still can not get redirect to the web authentication portal. Have the default configuration Internal (Default).
In laptops we check the firewall, dont have a proxy activate and have google DNS.. 4.2.2.2 8.8.8.8. In fact this laptops connected to this ssid before.
Can I set up a guest wifi connection on my Cisco WLC 2504 if I already have WLANs set up inside my corporate network? I want to use port 4 and connect it directly to my ISP so that it is outside of the corporate network. I set up an interface with a valid IP from the ISP and created a "Contractor" WLAN to use that interface.
View 6 Replies View Related
