setting up a 2504 on a 2960 switch. The management interface is up and pingable, and from the WLC we can ping vlan 20 (our wireless client vlan) gateway. However, when we create the vlan20 interface on the WLC, give it a valid address and assign it to a port, we can no longer ping the vlan 20 gateway from the wlc, nor can we ping the vlan20 interface from a PC. I’m told the 2960’s don’t do dot1q trunking…
View 6 RepliesI am unable to connect a Wifi Modem wiith 2960 Switch having VLAN 1,Attached is the network diagram,what configurations i have to modified it,I need to Connect A Wifi Modem on VLAN 1 ,Connectivity is working fine between VLAN 10 and VLAN 1.What should be the next step to Connect Wifi Modem to VLAN 1 so that Users on VLAN 10 should connect to Internet.
View 14 Replies View RelatedI've set up a WLC2504 with interface "mgmt" and "guest" (2 different VLAN IDs) both configured on port1.Now I'd like to be able to connect to PoE ports (port 3 and 4) 2 LAPs which should be able to get IP addresses from the DHCP as if they were connected to port1.
View 14 Replies View RelatedI try to add a Catalyst 2960 to Cisco Network Assistant, I get the prompt for password but I get a "Authentication failed". I use the same login / password for telnet that works fine. Http admin page is reachable but I cannot login with the "admin" account.
View 2 Replies View RelatedI have load CISCO-ENVMON-MIB and initiate walk in it but unable to find OID of Cisco 2960 temperature monitor. I have search over net and found .1.3.6.1.4.1.9.9.13.1.3.1.3.1 for temperature but this OID is not responding in this mib.
View 2 Replies View RelatedI have WLC 2504 and AP3502I . AP can not join wireless controller .
*May 24 16:33:51.871: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*May 24 16:33:51.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 10.80.90.99 peer_port: 5246
[code].....
I configured the below config in Routers it is working good , but when i do the same in SWITCH-2960 , i am getting a problem not able to login to enable mode ... i am getting the basic login only ....
Error msg : % Error in Authentication.
Need to be configured at TAFE Network Devices: Code...
I need urgent support on creating SSID as layer 2.We have cisco WLC2504 and 1602i access point. In our network we have in gate for guest.I want to create one ssid and bind with vlan only. We can not creat interface on WLC b/c of static IP.
View 3 Replies View RelatedI got a set of dhcp pool in one 3750 attached to diferent Vlans in the network, the wired network works fine, you can get from any switch port across the LAN a diferente VLANs IP. In my wlc2504 I got 5 WLANs with the DHCP server pointed to the VLAN in the 3750, but I just got one set of ip when i tried to connect to diferent WLAN, without connectivity, I can see all the Ap's, and ping the VLANs in the 3750,
View 4 Replies View RelatedI have two Wireless LAN Controllers 2504 and 8 APs 3502e. The WLCs are running software version 7.0.116.0. The problem is that I don't have the mesh option to configure indoor mesh inside the controller. In chapter 9 of Wireless LAN Controller Configuration Guide, Release 7.0.116.0 says that I have to go to Wireless Menu and select the AP. When I am inside the AP general page, the guide says I have to go to the Mesh tab, but that tab doesn't appear in the controller GUI. Do I have to use another image in the controller? Or do you have to use an special mesh code or something like that? Because in the download page of the controller it only appears the 7.0.116.0, two more new versions but there is nothing about mesh image.
View 5 Replies View RelatedI have the problem that the AP1130 can not join to WLC2504.
Console Messages of AP1130:
*Aug 14 09:34:54.029: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Aug 14 09:34:54.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.x.251 peer_port: 5246
[Code].....
I have a question about managing the Access Point:
-WLC2504
-AIR-LAP1262N-A-K9
First: I need the access point works by period, example: 08:00AM - 06:00PM after that disable the radio and return work next day at 08:00AM
Second: Also, if the radio no activity for a long period (e.g 60 or 120 minutes), disable the radio interface.It's possible with the WLC? Or maybe need implement one NCS?EnergyWise Technology - but, I only need "shutdown" the radio not the Access Point completely.
1) We have client setup, which has all PCs in Workkgroup , client has network sharing enable in LAN . Its work well in LAN , he don't have Local DNS , still he is able to ping or access sharing using device hostname
2) When Client moves into Wireless , he is not able to ping or access sharing using Hostname , but if used the ip details he is able to ping and do sharing using IP address onlye.
My Wireless Setup has WLC2504 and LWAPP Access Points.
I am having issue with integrating WLC2504 with Win2k8 server NSP radius server.
View 3 Replies View RelatedI have few question with WLC 2504 with 25 License AP. Our customer have SSID around 30 SSID then, is it possible to create WLAN around 30 SSID on WLC 2504? becuase i had tried to do it on WLC4404-25 License that can do or create WLAN with 30 SSID.
View 12 Replies View Relatedconfigured Cisco 2504 WLC with 1142 Aps... Guest wireless works fine
for the staff wireless I wanted to authenticate with 802.1x & Radius. So configured an external Radius server (Imprivata) and configured the 2504 Radius options for the extenal server.( Layer 2: WPA2-AES & Auth Key Mgmt: 802.1x )
When I connect a client to this wireless, the authentication fails, I wonder whether it is because of the client side settings..
Which trusted Root Certification Authorities need to be checked?
I have stack of 2960 S switches.I can console only from Master not from memember switches is this default behaviour?
View 1 Replies View RelatedI am having 2960 switch and one port is configured with a VLAN and connected with an unmanageable switch and further one more unmanageable switch was connected to the primary unmanageable switch…
The topology will be 2960 switch -> unmanageable Switch -> unmanageable -> PC connected
The issue I am facing most of the PC are getting IP addresses through DHCP server and very few 5 or 6 PC’s out are not getting the IP from DHCP server.If I switch of the switch and switch on the issue is resolved for those and it will raise for some other PC’s.
I have 2960 switch and i can't access it using my console cable .I can access other switches in my network ( 3560 & 2960 ) but i can't access only this switch.may be the console port in the switch damaged? or it's a bug ?? !!! although the switch is worked normally.
View 11 Replies View Relatedi have a device connected to 2960 switch. It is an access port and i could ping the device from other switches , also from outside the lan. But i am not able to ping the device from 2960 switch alone. I suspected and checked the arp table and it was showing as incomplete. I created the manual arp entry and tried pinging but no luck.
View 14 Replies View RelatedEvery time I power down my WLC2504 controller and then back up, the time reverts back to the year 2000.The APs can't join the controller, due to certificate errors, until I reset the clock. This problem just started recently.
View 6 Replies View Relatedhow can i replace my wlc2504 to a WLC5508 without disconnecting everybody, i have 3 SSID, on different VLAN.. I want the WLC5508 to be the main WLC, so i can remove the 2504 from the network. On the WLC5508, it will be the same configuration of the 2504. Is there a procedure or a wiki on such operation?
View 8 Replies View RelatedCan we change the internal web authentication for guest network to use http instead of https?
View 3 Replies View RelatedI have a set-up with multiple C2960 and C3750 switches. All these devices are being managed remotely. So basically I login to C2901, which is used as a Terminal Server, and reverse SSH to the console of each device. That's - I have assigned an IP to each port of the terminal server so that I can SSH directly to the desired device through via the mapped IP.
Now, recently I had to restart couple of switches - one C2960 and C3750. I initiated the reboot via console connection remotely. I could see the device logs for some time and then the logs stopped and there was no reaction from the console irrespective of any command I tried to enter.
I tried resetting the line on the terminal server, but that didn't work.
Now when I try to SSH the IP mapped to console of that particular device - i dont get any login prompt and there is no effect on device after giving any command. Although i can see the logs on the console session - but cant do anything.
I have a second way of connecting the device via inband- management, and checked the device config found it correct. It is same as other devices which are working correctly.
Both C3750 and C2960 are behaving exactly same - can see logs on console but see effect of even pressing enter - not getting login prompt as well.
I have 2 switches connected Via MM fiber cable one of them SRW2024-K9-NA with MGBSX1 Transceiver and the Secand One 2960 with GLC-SX-MM
are there is any configration must be done or not ?
I have an existing stack of 4 x 2960-S switches connected by stack cables.I would like to add another 2960-S switch to the stack but am unable to as the 2960-S will only allow 4 x 2960-S switches per stack.how I would add the 5th 2960-S switch to the existing stack of 4 x 2960-S switches.
View 12 Replies View RelatedI have a 24 port 2960-S that is not communicating with a 2960-LST that it is directly connected to over fiber. The link is up on the LST but will not come up on the -S. What command should I use to bring up this link? I have tried no shut from the (Config-if)# prompt.
View 3 Replies View RelatedIm trying to Connect a 2960-S Catalyst Switch to a 3560 Catalyst Switch. It worth pointing out im newish to switching although i know some commands and what they do This is my first time connecting 2 switches together.They are connected via a crossover cable and have green lights flashing on the connected ports When i run "show CDP neighbours it sees the new switch Unable to ping new switch...just timesout Here is the the interface on the 3650
GigabitEthernet0/40 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 001b.532f.8428 (bia 001b.532f.8428)
Description: Uplink to Switch 2
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
[code]....
I am having a problem in connecting two Cisco 2960 Switches between two different buildings using Cisco WLC 2504 & 3 Wireless 1552S APs.
- One AP is directly connected to Switch - 1 where WLC is connected and serving as a RAP
- Another one is working as Mesh in the field.
- Third one is a Mesh Access Point wired to another Switch - 2. (Bridging is enabled)
All the APs, WLC & switches are in the same network 10.3.x.x subnet mask : 255.255.240.0?WLC is working with default management interface whereas switches are having VLAN1 configured as default VLAN.All the port for the switches are Trunk ports?Once i am trying to ping the RAP or any MAP from Switch - 1 I am sucessful but once i am pinging Switch - 2, its not replying. Similar is that case from Switch - 2 side.
I need to connect these devices:
- Some computers.
- A Cisco Catalyst 2960 switch (computers must be connected to this switch)
- A ADSL router Zyxel P-660HN-T1A with WiFi (the switch must be connected to this router)
In my company we have at least 10 computers which were connected to Internet using a WiFi connection. But now we need these computers connected to a wired line and this router has just 4 Ethernet ports which are not enough obviously. So we bought this 24-port Cisco switch to connect all the computers and I don't know how to connect it to the ADSL router and what configurations to set up in order to have access to internet in every computer connected to the switch.
I just installed a new 2960 to replace a 3550 this last weekend. All of the fiber media converters will not connect to the new switch. The converters are made by Black Box and Desa. If I plug them into the 3550 they link up immediately. If I plug them into the 2960 there is no link whatsoever. I've tried letting it auto-negotiate and tried turning off inline power on the 2960 with no luck.
View 22 Replies View Relatedjust want to confirm if I could use the 2x 10GE uplink ports of a cisco 2960 to connect to my Server directly?
View 17 Replies View RelatedI need to connect these devices:
- Some computers.
- A Cisco Catalyst 2960 switch (computers must be connected to this switch)
- A ADSL router Zyxel P-660HN-T1A with WiFi (the switch must be connected to this router)
In my company we have at least 10 computers which were connected to Internet using a WiFi connection. But now we need these computers connected to a wired line and this router has just 4 Ethernet ports which are not enough obviously. So we bought this 24-port Cisco switch to connect all the computers and I don't know how to connect it to the ADSL router and what configurations to set up in order to have access to internet in every computer connected to the switch.