I've set up a WLC2504 with interface "mgmt" and "guest" (2 different VLAN IDs) both configured on port1.Now I'd like to be able to connect to PoE ports (port 3 and 4) 2 LAPs which should be able to get IP addresses from the DHCP as if they were connected to port1.
View 14 Repliessetting up a 2504 on a 2960 switch. The management interface is up and pingable, and from the WLC we can ping vlan 20 (our wireless client vlan) gateway. However, when we create the vlan20 interface on the WLC, give it a valid address and assign it to a port, we can no longer ping the vlan 20 gateway from the wlc, nor can we ping the vlan20 interface from a PC. I’m told the 2960’s don’t do dot1q trunking…
View 6 Replies View RelatedI have WLC 2504 and AP3502I . AP can not join wireless controller .
*May 24 16:33:51.871: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*May 24 16:33:51.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 10.80.90.99 peer_port: 5246
[code].....
I need urgent support on creating SSID as layer 2.We have cisco WLC2504 and 1602i access point. In our network we have in gate for guest.I want to create one ssid and bind with vlan only. We can not creat interface on WLC b/c of static IP.
View 3 Replies View RelatedI got a set of dhcp pool in one 3750 attached to diferent Vlans in the network, the wired network works fine, you can get from any switch port across the LAN a diferente VLANs IP. In my wlc2504 I got 5 WLANs with the DHCP server pointed to the VLAN in the 3750, but I just got one set of ip when i tried to connect to diferent WLAN, without connectivity, I can see all the Ap's, and ping the VLANs in the 3750,
View 4 Replies View RelatedI have two Wireless LAN Controllers 2504 and 8 APs 3502e. The WLCs are running software version 7.0.116.0. The problem is that I don't have the mesh option to configure indoor mesh inside the controller. In chapter 9 of Wireless LAN Controller Configuration Guide, Release 7.0.116.0 says that I have to go to Wireless Menu and select the AP. When I am inside the AP general page, the guide says I have to go to the Mesh tab, but that tab doesn't appear in the controller GUI. Do I have to use another image in the controller? Or do you have to use an special mesh code or something like that? Because in the download page of the controller it only appears the 7.0.116.0, two more new versions but there is nothing about mesh image.
View 5 Replies View RelatedI have the problem that the AP1130 can not join to WLC2504.
Console Messages of AP1130:
*Aug 14 09:34:54.029: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Aug 14 09:34:54.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.x.251 peer_port: 5246
[Code].....
I have a question about managing the Access Point:
-WLC2504
-AIR-LAP1262N-A-K9
First: I need the access point works by period, example: 08:00AM - 06:00PM after that disable the radio and return work next day at 08:00AM
Second: Also, if the radio no activity for a long period (e.g 60 or 120 minutes), disable the radio interface.It's possible with the WLC? Or maybe need implement one NCS?EnergyWise Technology - but, I only need "shutdown" the radio not the Access Point completely.
1) We have client setup, which has all PCs in Workkgroup , client has network sharing enable in LAN . Its work well in LAN , he don't have Local DNS , still he is able to ping or access sharing using device hostname
2) When Client moves into Wireless , he is not able to ping or access sharing using Hostname , but if used the ip details he is able to ping and do sharing using IP address onlye.
My Wireless Setup has WLC2504 and LWAPP Access Points.
I am having issue with integrating WLC2504 with Win2k8 server NSP radius server.
View 3 Replies View RelatedI have few question with WLC 2504 with 25 License AP. Our customer have SSID around 30 SSID then, is it possible to create WLAN around 30 SSID on WLC 2504? becuase i had tried to do it on WLC4404-25 License that can do or create WLAN with 30 SSID.
View 12 Replies View Relatedconfigured Cisco 2504 WLC with 1142 Aps... Guest wireless works fine
for the staff wireless I wanted to authenticate with 802.1x & Radius. So configured an external Radius server (Imprivata) and configured the 2504 Radius options for the extenal server.( Layer 2: WPA2-AES & Auth Key Mgmt: 802.1x )
When I connect a client to this wireless, the authentication fails, I wonder whether it is because of the client side settings..
Which trusted Root Certification Authorities need to be checked?
Every time I power down my WLC2504 controller and then back up, the time reverts back to the year 2000.The APs can't join the controller, due to certificate errors, until I reset the clock. This problem just started recently.
View 6 Replies View Relatedhow can i replace my wlc2504 to a WLC5508 without disconnecting everybody, i have 3 SSID, on different VLAN.. I want the WLC5508 to be the main WLC, so i can remove the 2504 from the network. On the WLC5508, it will be the same configuration of the 2504. Is there a procedure or a wiki on such operation?
View 8 Replies View RelatedCan we change the internal web authentication for guest network to use http instead of https?
View 3 Replies View RelatedWe have an ASA 5505. 5505 comes with two default vlans 1&2 with each of them marked as inside & outside respectively.My query is , if i do not want to use vlans on 5505 and only want to use the Ethernet ports as pure physical layer 3 ports, is it possible?i.e. i want to assign a layer 3 ip address on eth0/0 and eth0/1 and make them as the inside & outside interfaces rather than vlans. is it possible to do away with vlans in 5505 & will it work otherwise?
View 3 Replies View RelatedIs there a way to associate spare firewall ports with another port that is being used..For example...int gi 0/2 is being used currently for my web dmz. Its ip is 192.168.10.1..Is there a way for me to associate gi 0/3 with the same layer 2 as gi 0/2 ?
In my webdmz I use 2 ACE 4710 proxys in FT mode. I used a layer 2 switch to connect firewall and proxys together.
I would like to eliminate this switch if possible..and connect both 4710's (layer 2) direct to firewall.If I could make gi0/2 - 4 part of the same vlan, then I would be good to go.
How many of the 881 switch interface ports can be used as router ports, have used the 877 etc where i can use 2 but need a low cost router that supports 3 for routing. (needs to be physical ports)
View 2 Replies View RelatedOne of techs accidentally connected two access ports from different switches together. Since then, LMS is alerting them as being Link ports down. I tried to default the config and set them to access ports without any success. what I should do in LMS to recognize them as access ports?
View 2 Replies View RelatedIs it possible to use one port on a cisco 837 ADSL Router as a wan port and others as LAN Ports if we don't want to use its ATM Interface?
View 3 Replies View RelatedI have seen several cases where ISP's block traffic on both UDP and TCP ports 135-139 even in core firewalls. Port 135 should be Microsoft EPMAP service and ports 136-139 should be NetBIOS services. However, why do ISP's sometimes block traffic on those ports?
View 4 Replies View Relatedi am deploying some SG 300's to some remote sites and will have static IP's assigned to them. the elements that will be plugged into the SG 300's ports will be DHCP. Is there a way to find out what IP's are assigned by port? Either by the Web GUI, the console, a log, etc?
View 2 Replies View RelatedI have a Cisco 877 connected to a VSAT modem, and I can't open ports outside, I dont know why?The Cisco 877 Fa0 port is connected to the VSAT modem at VLAN9, and the rerst of ports are connected to the local lan network at Vlan2. I can enter to Internet, but I can't open port outside. ADSL over pots is not used here.I need to open port 81 for ip address 192.168.1.130 and I dont know why this isn't working. Also if I do: sh ip nat translations I see this:
sh ip nat translations
cisco877#sh ip nat translations
Pro Inside global Inside local Outside local Outside global
tcp 172.30.xx.122:81 192.168.1.130:81 --- ---
udp 172.30.xx.122:81 192.168.1.130:81 --- ---
[code].....
if i have four LAN ports on my modem+router , three of which are already occupied and i wish to add another three PCs to the same network, what hardware should i add to the fourth LAN RJ45 port so as to attach the other three PCs too.
View 1 Replies View RelatedSo the 2T comes with 2 10GE and 3 GE uplink ports. Can you use all 5, one or the other, a mix, or what? How does that work? It's not really clear from reviewing the products webpage or data sheet.
View 3 Replies View RelatedI would like to know if I can connect 4 sets of NX5596 (each NX 5596 will have 5 NX2K attached) to one set of NX7010 (each NX7K has 4 X N7K-F248XP-25 modules) and using 16-way port-channel for each set? I did some digging on the Cisco website and noticed on some of the old document stated that the NX7K only support up to 8 active vPC ports between both vPC peers.
View 8 Replies View RelatedI wonder if any of you now if there exists a small IPSEC box that can be put between units that don't support IPSEC? I'm not looking for a Wireless router with a WAN port. Only a small box with 2 ethernet ports and IPSEC client support.
View 5 Replies View RelatedI have a telephony system already in place with 6 FXO active ports configured on a 2821 Router.The thing is that I am not able to make an ip phone forward calls to a mobile No.I can make calls to the same mobile number when dialed from the phone but the call routing seems not to function correctly when call-forward all is configured on the ephone-dn.I would like to focus only on voice-port 0/0/0 and 0/0/1?
voice-port 0/0/0
supervisory disconnect anytone
output attenuation -3
echo-cancel coverage 32
compand-type a-law
cptone GB
[code]....
We have a DVR here at work that has a web interface on port 100. From our internal network we just use http:192.168.100.40:100. What is the best way to set that up on cisco 5510 firewall. I have cisco asdm and set a access rule: enabled=checked ; source=any ; destination= 192.168.100.40 ; service= tcp 100 ; action=permit. It shows a couple of hits when I go to [URL]
View 7 Replies View RelatedI need to configure a Cisco 887va router for a customer with a firewall that doesn't support PPPoA. I basically need to ensure all traffic that is recieved from the internet (ADSL connection) is NAT'd to a LAN interface so the firewall can do the specific NATing. I have the following route map and NAT rule in mind, but what I am confused about is that if the atm0 interface needs to be configured as the outside interface and vlan2 as the inside interface. How will the following work?
View 0 Replies View RelatedI have a Cisco 5508 controller and am considering using LAG. Can I enable LAG but only use 2-4 of the 8 available ports on the 5508? I am asking because currently I don't have enough ports on my 3750G switch to accomidate all 8 ports on the 5508.
View 2 Replies View RelatedWe just got a new ASA5510 (straight out of the box). I’m new to the Cisco but feel we followed the directions. We connect to the management port and have our workstation set to get an ip via dhcp. A cat5 is connected to the management port, that goes into a hub (tested to work) and a cat5 is connected from the hub to the workstation (tested to work). Nothing else is connected. The workstation does not get an ip address. (assigns APIPA) Both the 5510 and workstation have been rebooted.The workstation works otherwise. We have also connected both a crossover and straight through cable from the 5510 to the workstation. We have statically assigned an ip of 192.168.1.2 to the workstation and cannot ping the cisco (192.168.1.1).
View 2 Replies View RelatedI have a SA 520W with the following configuration:
-WAN port: Internet access for web browsing and QuickVPN access for remote users
-Optional port: Configured as WAN, for VPN access to another office (Office 2) in the same building throung a public network
-Ethernet ports: Computers on Main Office.
So far I have been able to configure communication between Main Office and Office 2 via VPN.Office 2 have no Internet access, so I need to share the Internet access from Main Office.QuickVPN clients have no access to Office 2, only to Main Office.