if i have four LAN ports on my modem+router , three of which are already occupied and i wish to add another three PCs to the same network, what hardware should i add to the fourth LAN RJ45 port so as to attach the other three PCs too.
View 1 RepliesWe have an ASA 5505. 5505 comes with two default vlans 1&2 with each of them marked as inside & outside respectively.My query is , if i do not want to use vlans on 5505 and only want to use the Ethernet ports as pure physical layer 3 ports, is it possible?i.e. i want to assign a layer 3 ip address on eth0/0 and eth0/1 and make them as the inside & outside interfaces rather than vlans. is it possible to do away with vlans in 5505 & will it work otherwise?
View 3 Replies View RelatedIs there a way to associate spare firewall ports with another port that is being used..For example...int gi 0/2 is being used currently for my web dmz. Its ip is 192.168.10.1..Is there a way for me to associate gi 0/3 with the same layer 2 as gi 0/2 ?
In my webdmz I use 2 ACE 4710 proxys in FT mode. I used a layer 2 switch to connect firewall and proxys together.
I would like to eliminate this switch if possible..and connect both 4710's (layer 2) direct to firewall.If I could make gi0/2 - 4 part of the same vlan, then I would be good to go.
How many of the 881 switch interface ports can be used as router ports, have used the 877 etc where i can use 2 but need a low cost router that supports 3 for routing. (needs to be physical ports)
View 2 Replies View RelatedOne of techs accidentally connected two access ports from different switches together. Since then, LMS is alerting them as being Link ports down. I tried to default the config and set them to access ports without any success. what I should do in LMS to recognize them as access ports?
View 2 Replies View RelatedOn my home network I have two computers:
PC#1 - my main computer
PC#2 - my laptop
Each of these has Windows 7, Avast! Anti-VirusToday I was working on a website on PC#1. When I attempted to upload the files via FTP, the connection failed repeatedly. When I went onto PC#2 it worked first time.I also tried to launch World of Warcraft on PC#1, this failed. It worked first time on PC#2.Websites work fine, so port 80 appears to be okay.I have reset my router to factory settings. ipconfig /release /renear /flushdns all made no difference.
How can I allow all ports to be open? I don't really want my 1811 to block any traffic. I tried the command access-list 1 permit any which allows me to surf the internet, but when I check my web server, and port 3389 (Remote desktop) on yougetsignal.com it says those ports are blocked.
View 6 Replies View RelatedI have a switch containing 48 connections. I have a patch panel that links to lots of access points in my building. One access point was not connected but needed to be but I didn't have any spare switch ports. I therefore reconnected switch 23 from one position (and thus one access point) to another position on the patch panel. Everything worked fine and this new location had network and internet access. Then however a few weeks later I had to change it back so i changed the connection of port 23 to the old position on the patch panel. When i did so port 23 showed a red light and then no light. Later I had to change it back to the other location but when i did so port 23 now shows no light whatsoever. It's as if the connection port just stopped working. Now both the old and new access point locations have no connection and I can't understand why.I tried rebooting the server but no luck. I tried connecting that access point through the patch panel to a different connection port but still no luck.
View 4 Replies View RelatedIs it possible to use one port on a cisco 837 ADSL Router as a wan port and others as LAN Ports if we don't want to use its ATM Interface?
View 3 Replies View RelatedI have seen several cases where ISP's block traffic on both UDP and TCP ports 135-139 even in core firewalls. Port 135 should be Microsoft EPMAP service and ports 136-139 should be NetBIOS services. However, why do ISP's sometimes block traffic on those ports?
View 4 Replies View RelatedI was told i need to open certain ports to certain IP's,what ports need to be opened to what IP's for the folowing game as im close to giving up.The games are as follows - Call of Duty 4, Counter Strike 1.6 and Source, Warcraft III, and StarCraft 2
View 2 Replies View RelatedI have a single physical machine A (Windows XP). On A, I have 3 virtual machines (A1,A2,A3) If a want to communicate with port 4444 on virtual machine A1, can communicate to the same port 4444 on machine A2, All the VMs below exist on the same physical machine.
View 3 Replies View RelatedI have opened the ports up on my Virgin Super Hub, and everything else in my house connected to this network can access the ports which I've opened, however just on this PC, I can't seem to open them, I've tried closing my firewall, and that didn't work either.
View 18 Replies View RelatedI had a DI 604 router and I couldn't forward ports, someone told me to buy a new router because my modem (TM602G) doesn't have a built-in router and can't be blocking it so I bought a DIR 601 with wireless and I still have the problem.I don't have any firewalls.
View 19 Replies View RelatedThe problem is I don't know what to do to open my modem's ports because every single of them except of 80 is blocked,im having some latency problems on online games etc, I asked my ISP and they didnt probably understand what the port is they offered me changing my IP to PUBLIC IP for onetime payment, seeing as they probably dont know what the port is im confused now, will the public ip unblock the other ports?
View 19 Replies View RelatedI am currently using OpenVPN with Your Freedom to bypass my school firewall to access the internet (ports for gaming are blocked)
I read the other day that I can connect to my home internet from here and have my computer behind this firewall just use my home internet connection.
What is the best way to add more ethernet ports to my router? Is it to daisy chain a hub /switch to it? I'm all out and I often work on many computers at a time. Currently I have the cable modem, my computer, printer, one spare for computers I work on, and one to vonage modem. I would like more available for computers that I work on so I can hook up at least one more.
View 5 Replies View RelatedNo ports seem to open up when they are supposed to be open according to the routers GUI.When i use "port checker"-websites, they even say that port 80 is closed until i actively open it in the router, then it shows up as open. This however only applies to port 80, no other ports shows as open OR allow any traffic through.The same thing happens when the router is in DMZ.What I have done so far is google my butt off without any results, I have tried a new router, a new network card, formated, re-installed windows and made sure that my ISP is not blocking the ports that i have tried to open.My purpose of opening a port is to run a mumble server, which I have run on a Hamachi VPN so far, and that has worked fine.
View 10 Replies View RelatedI have an issue with virtual box as it is blocking all my ports when the adapter is set as bridged. My OS is Windows 7 and the OS I am trying to connect to is Win 2k3 Server.
I made it bridged to be on the same LAN. how I can open ports and can be able to telnet for example port 80?
I can't open up any ports.I've tried using applications such as Simple Port Forwarding, PFPortChecker and manually by opening my router gateway (192.168.1.1).I can open a port, but if I check whether the port is open, it says that the port is closed. I tried opening ports through Windows Firewall and even disabling firewall, still won't work.
View 14 Replies View RelatedIve been having trouble opening any ports on my windows 7 desktop. I connect wirelessly to my D-link Dir 655. I've tried port forwarding single ports to a static ip, but that didnt work either. I currently have the dmz server enabled and still no ports are open according to this port checker Open Port Check Tool - Test Port Forwarding on Your Router I have the windows firewall service disabled, upnp is enabled on my computer and router, i have spi firewall disabled, qos is disabled, and endpoint tcp/udp filtering on endpoint independent.
View 3 Replies View RelatedI have 3 systems. I would like to connect PC 1 to PC 2 & 3 .But not between 2 & 3. ie. 3 & 2 must be connected to PC 1. I want gigabit connection between them. The purpose is realtime streaming of audio from PC 2 & PC 3 to PC 1. The only data that goes fom PC 1 to 2 & 3 is MIDI information and automation. The problem now is that I'm having dropouts in audio, and bandwidth limitation.
whether using a dual port PCI-e lan card on PC 1 and single port card on PCs 2 & 3 or using a gigabit switch would be better. how to configure the ports for this type of a connection ( if possible that is ). Does using dedicated network cards with on-board processors and ram take all the networking load off the system's cpu and ram.
I have 2 PC's networked via a gigabit switch. They are both running Windows 7 Ultimate 64-bit and are on the same workgroup.Addresses Of both - A: 192.168.0.1 , B: 192.168.0.2 , Both are on the same subnet 255.255.255.0.Can I have 2 LAN ports on the PC - "B" , with 2different IP addresses But connected to the same workgroup.I don't need the second port for accessing the PC-B or accessing any of its files or anything. But can 2 programs access each of these ports independently.
View 1 Replies View RelatedI'm trying to open ports 2934 and 2935 UDP on my Linksys E1000 router in order to play Falcon 4: Allied Force multiplayer but it's not working.I've correctly created a static IP, and logged in to the E1000's page. Under "Applications & Gaming", and then under "Port Range Forwarding" I entered values thus:
[code]....
My reports say that my listen ports are blocked even though I removed my router already. I've enabled these ports in Windows firewall already. Why are they still blocked?
View 4 Replies View RelatedI have 3 xbox 360s in the house and im having nat trouble with them, i am currently using an actiontec pk5000, from centrylink. i need to know if there is a way to open all ports on this router or if i should get a router/switch that i can open the ports on and use dmz on the actiontec for the new router to make this work.
View 2 Replies View RelatedI have a question regarding uplink ports on a switch. Specifically the SFP+ variety. Could these uplink ports be used to connect directly to a fileserver? To be more specific, would the uplink port on the HP 3800 Switches connect directly to a file server that has the SFP+ card installed?
View 6 Replies View RelatedI cannot successfully forward ports on this router, I've tried a few things but I can only assume the firmware is bad. I've already looked around for a solution but everyone says they solved it by just getting a different router (which at the moment isn't an option).
View 3 Replies View RelatedI am thinking about opening a port for a certain multi-player game. I was just hoping to know if opening a port for this game could leave me vulnerable to hacking or other stuff like that.
View 4 Replies View RelatedAny VoIP box which has from 3 to 10 phone ports?I'm sourcing the box for a business that wants to connect about 8 phones to the box, then have the calls terminated on our partitioned platform hosted by a third party.
View 3 Replies View RelatedI have this problem i can't open my ports on my D-link 524, i have opened about 6 ports so that my XBOX 360 works with a open nat, i have also set the DMZ to my xbox's IP which is static btw, my PC is also static. This is how i basically tested and it told me that it was not opened. I went into:
192.168.0.1 -> Advanced -> Virtual Servers ->
Enabled
Name: XBL1
Private IP: 192.168.0.100 ( because i was testing it on the computer - if it
were 360 it would be .141 )
Both UDP and TCP at port 3074
Schedule=Always
Apply -> Then restarts modem/router i waited for 2 minutes before turning them on again, i turned router on first because some guide told me to do that.
I did exactly what they did on portforwarding.com then i opened up portchecker and typed in 3074 and pressed check -> This port is NOT opened. What is wrong? This is how my net is set up.
Modem ZyXEL -> D-Link 524 -> D-Link DGS 1005D -> Computer/XBOX.
I can't get port forwarding to work, even when I turn off the Windows 7 firewall and AVG anti-virus software I'm running. I entered the IP address of my laptop (with a DHCP reservation) and UDP and TCP port numbers, with Schedule set to Always and Inbound Filter set to Allow All. That should be it, right? However, when I check the ports using PFPortChecker, both the UDP and TCP ports are blocked. I do have a Linksys wireless router daisy-chained to the D-Link router, but I'm not communicating on this computer through the Linksys router and the problem still occurs even when the other router is disconnected, so that doesn't appear to have anything to do with the problem. I just updated to the latest firmware (3.13NA).
View 11 Replies View Relatedi am deploying some SG 300's to some remote sites and will have static IP's assigned to them. the elements that will be plugged into the SG 300's ports will be DHCP. Is there a way to find out what IP's are assigned by port? Either by the Web GUI, the console, a log, etc?
View 2 Replies View Related