I have 3 systems. I would like to connect PC 1 to PC 2 & 3 .But not between 2 & 3. ie. 3 & 2 must be connected to PC 1. I want gigabit connection between them. The purpose is realtime streaming of audio from PC 2 & PC 3 to PC 1. The only data that goes fom PC 1 to 2 & 3 is MIDI information and automation. The problem now is that I'm having dropouts in audio, and bandwidth limitation.
whether using a dual port PCI-e lan card on PC 1 and single port card on PCs 2 & 3 or using a gigabit switch would be better. how to configure the ports for this type of a connection ( if possible that is ). Does using dedicated network cards with on-board processors and ram take all the networking load off the system's cpu and ram.
I have a home wireless network and my service provider is Suddenlink. I use a DLink modem and have two Tosiba laptops. All of this has been working fine until this morning when one of the laptops won't connect to the internet. when I run the trouble shooting guides on it I get messages that the problem is that the modem won't connect to the internet. However, the other laptop (this one) is working fine. when I look at the network map i see both computers and a green line to the modem. on this computer, there is also a green line from modem to internet. the other computer shows a res x on the modem to internet line. this is a sudden change i have restarted the computer the modem and the router. I can also conenect this computer to the internet via a mifi that I have but not the other laptop. there are no red x's on any of the hardware when I go to the "manage" computer.
Here is my setup: 1- laptop1 is windows 7 with 192.168.1.1, submask 255.255.255.0 2- laptop2 is windows XP with 192.168.1.2, same submask as above. Laptop1 connects via CAT5 (non-crossover) RJ-45 into a switch (port 1). Laptop2 connects via CAT5 (non-crossover) RJ-45 into port 2 of switch. Both ends of the CAT5 are, of course, connected into each laptop's network connector.pinging resulted in timed out from both.
I have two computer but one monitor. and i wanna connect both computer with one monitor, one keyboard & one mouse. Like KVM switch. but if i connect with KVM switch then i can turn on one at a time & if i wanna use another one so i hv to turn off first one.
so how can we connect 4 remote computers so dat they can share data,as well as if data is updated on 1 pc ...it is automatically updated on rest 3.....
my three computers cannot connect to the internet, they were fine last night now it says. cannot comunicate with primary sever, do you think it is my comp or sever.
First 3 days ago i came in to my work and my 2 Desktop computers where not connecting to the internet. After trouble shooting i found that my cell phone and wireless computer would connect. then hardwiring with my cat5 cable my laptop worked as well. i couldn't connect to the router as well from the 2 Desktop computers. restarted every thing router modem computers ext. nothing.Then i tried ping tests nothing could not ping each other or the router. though the network map clealy told me the ip addresses of each computer and that it was connecting. then as though from random i tried again to log in to the router. 192.168.2.1 and one of my computers found it and could then connect to the internet.
I have a Windows 8 Pro laptop, and a new Windows 7 Laptop. When I try to setup the connection so that I can share files and folders between the two computers, I am asked for the User name and the password. I see the password in the homegroup, but entering it does nWhat is the user name in this case? My computer name or the other computer name or something else
How to connect my 5 computers to an internet. i already have a hub and lan connections but the other 4 computers still don't have internet connections.
I want to put a laptop in the barn, with a web cam. I have a phone line (with spare wires) running to the barn and I want to connect my house laptop to the one in the barn.How do I do this?
So I set up my router and modem and I have the modem connected to the linksys router and the ethernet port to my computer. The computer with the ethernet cable works fine, but all the other laptops can not connect to the wireless.
Everything was working fine, and various computers, tablets, and even my smartphone, all hooked up to my router without any problems. Somehow, this week, first my Asus U56E wouldn't connect (before all this it was automatic), and then my Google chromebook wouldn't connect either. The Asus is my main computer. And the reason for writing. I just mention the chromebook because they both quit connecting at same time, pretty much. But still my old xp netbook connects, as does my new google nexus7 tablet. And my nexus one phone. All hook to wifi, with no problem.I tried everything I could think of: This is a Dlink Dir615 router. Even set a new wireless network up, but it doesn't seem to connect. I ran the Windows Network Diagnostics, and it reset everything, and looked like it was fixing it, but no go. It said to investigate router or access point issues. I did what it said, and what has always worked with these problems. Turned off router for about 1/2 minute, then restarted it. Then did the same with the Cox motorola modem, *and* the router, but still, just doesn't want to connect. Wireless, that is...no problem with ethernet.Finally pushed the little pin in in the back of router, and reset the router entirely. Set all up again. Same thing happens, it just doesn't seem to recognize these two computers. So just to be sure, I used my nexus one as a wifi point: and these computers hook up fine, so it seems to be something with the router. My ISP is Cox. Cable. Router D-Link Dir 615, latest firmware. Modem Cox issue Motorola Surfboard. Antivirus Microsoft Security Essentials, and Win7 Firewall (I tried with these two turned off, but still no).I include the xirrus app's output...My wireless network on that app is 'phubai' and that is the one that won't connect. I had trouble bringing it up on Xirrus, too. It would only show when I would attempt to connnect, then it would disappear again.
ipconfig /all C:Windowssystem32>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : geffASUSpc rimary Dns Suffix . . . . . . . :
I just loaded up my machine with Windows Vista Home Basic and wanted to connect my another laptop to it via Wireless AdHoc network. I created a wireless adhoc network from the network and sharing center. But was unable to connect the other laptop to it. Everything is ok. My WLAN is on, drivers are also latest.[code]
My XP laptops cannot connect to my TEW-639GR router over wifi. I get the "Limited or No Connectivity Message". The same 2 XP laptops can connect if they are wired without problems.My Ubuntu computer can connect to wifi and wired without problem."Limited or No Connectivity" usually means a DHCP problem in XP. I have DHCP turned on on my router.This problem did not immediately start when I first set up the TEW-639GR. It happened infrequently on my XP laptops initially for about 2 months but now it happens all the time.
My XP laptops cannot connect to my TEW-639GR router over wifi. I get the "Limited or No Connectivity Message". The same 2 XP laptops can connect if they are wired without problems.My Ubuntu computer can connect to wifi and wired without problem."Limited or No Connectivity" usually means a DHCP problem in XP. I have DHCP turned on on my router. This problem did not immediately start when I first set up the TEW-639GR. It happened infrequently on my XP laptops initially for about 2 months but now it happens all the time
just got internet today and set up the wireless on the router using a laptop connected through LAN. All computer now connect to the router through wireless except the the laptop that was used to set it up.
i have a laptop and a desktop, everything was working fine until i messed with something in the router settings by accident, i changed some type of security setting and then changed it back because i was testing something.. at this point i had to remake the network for some reason, whcih was no problem i put in the pin and security code and i was able to connect through my desktop with no problem.. a few hours later i realized my laptop could no longer connect.. i recieved the unable to connect error.. i read that it could be the security settings, so i assumed i switched something before by accident and i restored to factory defaults...
after i did this my laptop could connect to the internet but my desktop couldnt connect! so it basically reversed itself.. i dunno what could be the problem.. i tried 2 of the 3 authentication modes because i am afraid if i try the 3rd i will lose internet completely then i will have no clue what to do..
I can't connect to one website. Not on my computer, not on my father's computer. I think the network is the problem, which is why I'm posting here. The website was working even yesterday but during yesterday evening, it stopped working and it's been like that since. I don't know how to fix it. My command prompt says my server can't find that one website and says my server failed. I tried other things like scan my computer, restart it, look at my Chrome settings, my firewall settings, nothing worked. I'm not sure what's going on here, because the network is private, and the contact information for 2Wire/Pace was useless for me, so I don't know what to do.
I'm having trouble trying to connect 3 computers via LAN for gaming using straight Ethernet cables and a net gear router. Only 2 computers seem to connect at a time. All 3 can connect to one another (one at a time) and the I.P. addresses have been set to 192.168.0.1 , 192.168.0.2 and 192.168.0.3. The cables work fine and the computers, but I'm wondering if I'm using the wrong kind of hub/router?
My laptop is connected to USB modem for internet connection. I would like to connect another computer to same internet connection. So i used LAN cable to establish connection. it worked well for first time. But now it is not connecting. how to connect two computers to same internet connection?
I want to connect my laptop with another one via remote connection. But I don't know how to connect. I'm having the team viewer software installed in my two laptops. How to get my PC's connected through remote assistance.
Due to the recent security issue with AnyConnect 2.5.2019, the ASA pushed AnyConnect 2.5.3041 to the all of the Windows and Mac computers. After the upgrade, some of the Mac OS X computers can't establish a VPN session when using the new client. Downgrading the client to 2.5.2019 resolves the issue.
I understand ip addressing and what a subnet is.But why is it sometimes I connect two things together,it always requires a subnet mask, and other times no? For example when I try to connect two computers together, it requires both IP and subnet mask.But if I use FTP software all it ask for is IP.Same thing when connecting to a website through their ip, doesn't require subnet.
