So I set up my router and modem and I have the modem connected to the linksys router and the ethernet port to my computer. The computer with the ethernet cable works fine, but all the other laptops can not connect to the wireless.
View 14 RepliesJust installed the E3200. Can connect other computers but not IOS devices to the router, except through the "guest" port.
View 2 Replies View RelatedEverything was working fine, and various computers, tablets, and even my smartphone, all hooked up to my router without any problems. Somehow, this week, first my Asus U56E wouldn't connect (before all this it was automatic), and then my Google chromebook wouldn't connect either. The Asus is my main computer. And the reason for writing. I just mention the chromebook because they both quit connecting at same time, pretty much. But still my old xp netbook connects, as does my new google nexus7 tablet. And my nexus one phone. All hook to wifi, with no problem.I tried everything I could think of: This is a Dlink Dir615 router. Even set a new wireless network up, but it doesn't seem to connect. I ran the Windows Network Diagnostics, and it reset everything, and looked like it was fixing it, but no go. It said to investigate router or access point issues. I did what it said, and what has always worked with these problems. Turned off router for about 1/2 minute, then restarted it. Then did the same with the Cox motorola modem, *and* the router, but still, just doesn't want to connect. Wireless, that is...no problem with ethernet.Finally pushed the little pin in in the back of router, and reset the router entirely. Set all up again. Same thing happens, it just doesn't seem to recognize these two computers. So just to be sure, I used my nexus one as a wifi point: and these computers hook up fine, so it seems to be something with the router. My ISP is Cox. Cable. Router D-Link Dir 615, latest firmware. Modem Cox issue Motorola Surfboard. Antivirus Microsoft Security Essentials, and Win7 Firewall (I tried with these two turned off, but still no).I include the xirrus app's output...My wireless network on that app is 'phubai' and that is the one that won't connect. I had trouble bringing it up on Xirrus, too. It would only show when I would attempt to connnect, then it would disappear again.
ipconfig /all
C:Windowssystem32>ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : geffASUSpc
rimary Dns Suffix . . . . . . . :
[code]...
just got internet today and set up the wireless on the router using a laptop connected through LAN. All computer now connect to the router through wireless except the the laptop that was used to set it up.
View 1 Replies View RelatedWhat would be the best way to connect 10 computers to a 4 port router?
View 1 Replies View RelatedI have a SMC Gateway Router and 2 computers connected to it with RJ-45 cable. They are (1 iMac + 1 PC) 150 feet apart both computers are wired to the router. I also have a Canon Pixma MP 560 Multifunction Inkjet printer that has the capability to be connected both wired and wireless. Right now it is only connected to the iMac via a USB connection as all 3 (router, iMac and printer) are on the same workstation.how to connect the printer so it could also support the 2nd computer a Windows PC which is located on the floor below. Can I do that through the wired router too? If not possible, I also have the capability to connect wirelessly although I would prefer to use the wired connnections.The PC has a Belkin USB 2.0 Network Adapter for wireless connection; both SMC Router and Belkin USB adapter are 902.11 N capable.
View 1 Replies View RelatedI have been searching the net for a hub of some sort for a home office. I need it to be able to support printers. It needs to be a wireless router and have a data storage which can be accessed by multiple computers. Like a backup. But the main thing im worried about is if it can be protected by antivirus and stuff.
View 1 Replies View RelatedI recently switched internet service providers from AT&T to Time Warner and ever since I have been unable to connect to my Netgear router with my computer's wifi. However, I have successfully connected my TV wirelessly to said router. One other note, my computer's wifi seems to recognize that the netgear router is there but it just refuses to connect me to the internet
View 7 Replies View RelatedI have a SMC Gateway Router and 2 computers connected to it with RJ-45 cable. They are (1 iMac + 1 PC) 150 feet apart both computers are wired to the router.I also have a Canon Pixma MP 560 Multifunction Inkjet printer that has the capability to be connected both wired and wireless. Right now it is only connected to the iMac via a USB connection as all 3 (router, iMac and printer) are on the same workstation.how to connect the printer so it could also support the 2nd computer a Windows PC which is located on the floor below. Can I do that through the wired router too?If not possible, I also have the capability to connect wirelessly although I would prefer to use the wired connnections.The PC has a Belkin USB 2.0 Network Adapter for wireless connection; both SMC Router and Belkin USB adapter are 902.11 N capable
View 7 Replies View RelatedI have and 880 W router. The LAN members can get out t o the internet. Now I want to configure NAT such that outside computers can access a couple of the machines using Remote Desktop (RDP). I am using Configuration Professional.
When I configure inside to outside, the remote computers can't connect to the target machines.When I configure outside to inside, the target machines acn't get to the internet.
When I try to use the advanced NAT definition wizard, I can't complete the task because the only inside pool (?) or LAN (?) is "designated" and not available to select. I can't free it up without deleting the one working NAT entry which is the one that enables all computers to reach the internet.
Why there is no parental control feature built in for WAP610N... how do i block website on all computers connected to my router?
View 4 Replies View RelatedI have two WRT54GL wireless routers. I have a computer and printer in my office connected to one of them. I'd like to add a computer and printer back in the shop to my network without using a wired connection. Can I use the 2nd wirelss router so that all computers and printers are on one network?
View 6 Replies View RelatedI ordered a linksys E1500 for a home office. There are 3 computers that connect wirelessly: a 8-year-old desktop with a Netgear USB adapter, a 1.5 year old laptop and a 3.5 year old netbook, both with internal wireless cards. The desktop and netbook are running Windows XP and the laptop runs WIndows 7.
The desktop (XP) and laptop (Windows 7) are able to connect with no problem. However, the netbook (XP) is having problems connecting. It is able to connect to the router using the WPA2 key, and says it has excellent signal. However, when I start up an internet browser, it gives me a DNS error for any page I try to access. Connecting directly to the router with a cable works fine.
I got on the phone with Linksys support. They told me the problem was that the computer wouldn't use WPA2, but when I switched to WEP, it didn't work at all! I switched back to WPA2 and have the same problem as before: it connects to the network but DNS error messages for any website I try to access (And I've tried both Chrome and Explorer).
To make things more interesting, I set up a guest network on the router, and the netbook connects fine through that so far!
Recently i have been having LOADS of problems with my wireless router. Every now and then it will decide that 2 of my 3 computers will not be allowed to connect to the internet. and i will have to spend hours of resetting and rebooting computers to get it to work again.. only for the issue to start again a few hours later. I recently added the third computer but im not sure how that would be an issue.
the router is a Linksys (cisco) WRT54G2.. a
I have a E2500 connected to a cable modem as the base of my home network. Hard wire connected to the E2500 is an linksys 8 port hub and a couple of computers. The 8 port hub is connected to a couple of computers and a xbox. I have the hub as a distro point to cut down on wiring. Wirelessly connected to the E2500 are a variety of laptops, netbooks, ipods, an ipad, a playbook, an iphone, a android phone, a wireless printer and a Ps3. Most of the devices are just using the wifi for internet access. Most devices have been setup with their own ip addresses to avoid ip conflicts. The computers and laptops/netbooks are running either Windows XP, Windows 7 or Mepis Linux. Up until now everything was going as good as can be expected, all the computers could see each other and most could transfer files between each other except when Windows gets picky.In the last few days no computers can see each other. Windows or Linux.Everything can accsess the internet and wirelessly print still just can't see each other. I reset the E2500. I updated the firmware on the E2500. I installed the Cisco Connect software (just in case I was too stupid too setup a router). Still nothing. I can ping other machines from a command prompt in windows or a terminal in Linux and get a good ping back. In the router setup via a browser I can go to the status page and see other devices on the local network but most are just ipods, ipad, playbook and the wireless printer, If I go to the administration page / diagnostics I can ping other computers and get a good answer. I just can see them from each other. I think I've rebooted every thing at least once. Yes the workgroup names are all the same (workgroup) and yes file sharing is turned on on all computers.
View 3 Replies View RelatedI've got an RV042 router at home and am connected from my office via the QuickVPN client ver 1.4.1.1.2. I can ping the RV042 and log into the administration page and make changes. However, I can not see other computers on the remote network. I can not ping them. When I open my Network page, I still see the computers on my local network.
All machines are running Windows 7 Ultimate. ISP is Comcast at both locations. WAN IP's are dynamic, but have not changed in over a year. Local IP's on the remote (home) network are static..[url]....
I have a mac 10.7.4 and an xbox 360 slim. Whenever I try to play online like cod or fifa and someone else is on the computer It is super lagy, Laging. Before when I had a **bleep**y netgear 33 mb it worked perfectly fine. Now this router is has 300 +mb and it stil doesnt work. This router cost me $80 dollars. Before cisco linsys I bought a netgear not the **bleep**ty neatgear but a newer one and it still had the same problem.
View 1 Replies View RelatedI purchased a E3000 Router to replace a dead Dlink about a week ago..I have 4 wired computers on my network. All in the same workgroup. I have 2 computers connected directly to the E3000, and 2 computers connected to a ProCurve managed switch on the other side of the house. I can ping the computers on the switch side of the network but i cannot see those computers in the network section of windows 7. I can also navigate to them via \ computername.
View 7 Replies View RelatedI just got a new WRT54GL wireless router to replace my WRT54GS failing router and I have a question. It's been awhile since I installed the old router and I remember something about not using the CD as it says before plugging in the new router because it messes everything up. All of my computers are running XP Pro SP3 with 2 of them being wired.
I remember something about just plugging the router in and typing in 192.168.1.1 in my browser and then setting everything up that way. Am I correct in doing this or am I forgetting something?
Oh, I am also running Network Magic so would I also have to reinstall it?
Recently installed an E4200 router to an MacPro following the setup as directed by Cisco Connection (connect Ethernet to router and then computer to router.) The wireless and the hard-wire connectivity works fine with accessing the internet. However, we have lost the ability to connect to other computers on our LAN via the Shared folder connection. This is usually accessed via the Sidebar (see image)
However with the E4200 in the mix, all we see is the router per its "given name" (what it was named on installation). I have tried to follow the advice mentioned in other threads, such as "Can't access network shares with E3000" and nothing worked-- and those threads seemed to apply to Windows and PCs anyway.
How can I see network rate of other computers connected to my WRT54GL wireless router?I have admin password and I want to see how much bytes/sec received and sent from all the computers connected to the router.
View 2 Replies View RelatedI have a EA3500 and my wireless computers keep getting disconnected about every ten to fifteen minuets. I have the newest firmware. My android phone also is having the same issue. My internet connection is stable and my wired connections do not get disconnected at all at any time. Is there something I need to setup in the configuration to resolve this?
View 1 Replies View RelatedI have two Windows 7 machines connected by wireless-N to my WAG160N. I frequently find that, although both computers can see the network, they can't see each other. I can temporarily solve this problem by disabling, and then re-enabling, the Wireless MAC filter.
View 9 Replies View RelatedI have a Linksys WRT54GS router that I have installed dd-wrt on.My household is overloaded with wireless devices, and living in a home of 6, speeds for everyone seem to slow down drastically later at night when everyone is simultaneously connected and streaming media -- whether it be Netflix, YouTube, etc.. My typical speed wired to the router with no other connections is around 25 mb/s down and 1-2 mb/s up.Obviously, it's going to slow to a crawl when we have an iPad, 3 iPod touches, an iPhone, a Wii (playing Netflix) and 4 PCs all connected simultaneously.What I need to do is give my personal computer priority and throttle all other devices. So that I myself will have decent speeds while hampering all of the other household connections. I rely on those speeds for my job and that should have priority over my brother watching music videos on YouTube.
View 1 Replies View RelatedIs the BEFSR41 Ver 3.1 compatible with Windows 7, 64 bit computers?
View 2 Replies View Relatedjust replaced a WRT54G with E4200. Most functions work well. 4 wireless computers (1 Macbook, 3 Win 7), 1 wireless android, 1 wired Win7 computer, 1 ethernet connected hard drive, 1 ethernet connected printer. All computers can ping router, access hard drive, access internet, ping android and ping Macbook.However, router, nor any computer, can't ping Win7 computers. Apparently IP based connections between WinX computers is blocked. My real applications are to Remote Desktop Connect from 1 Win7 computer to another, or to run a DLNA music server on 1 Win7 computer, accessed by another. (the LAN connected computer is the server, accessed by a wLAN client. All worked fine on WRT54G router, but can't connect thru E4200. When these apps failed, I tried PING, and that failed as well.All computer's IP addresses are properly served from E4200 via DHCP, and are visible thru the router's DHCP Reservation panel.
View 1 Replies View RelatedI just installed the E2500 to replace my older router. With my older router I was able to share files between the different computers in my house. All I did was replace the old router with the new one and now they cant share files? I looked through the router settings and cant find anything showing firewall blocking the file and print sharing. why I cant share the files and how to allow the file sharing?
View 1 Replies View RelatedI have 3 laptops connecting wirelessly to this router. One is running at 18Mbps, the other two at 0.4Mbps. the internet setting are the same and the security is the same (WPA2-Personal with AES encryption). One of the slow computers is brand new and WAY faster than my "fast internet" computer. The other is about the same as the "fast internet" computer. I updated the I connected the new computer to the router tusing an ethernet cable and it had superfast internet. I redid the Cisco connect on each computer, but it didnt change anything. Why is it so slow wirelessly?
View 4 Replies View RelatedI,ve used a network for a number of years with no problems. I have databases on computer 1 and access them with computer 2. After installing a Cisco e2500 I can connect to the databases but after a short period of time I am disconnected. If I search my network computer 1 is not found. Waiting a few minutes the network will find computer 1 again. At about the same time my firewall software has started to show an attack from an 2 different IP's I don't recognize but its always one of those 2 IP's. I'm assuming the two problems are related. I,ve considered going into my firewall and allowing the unknown IP access, BUT who knows where that IP is coming from. I've checked the Cisco setup but couldn't find an IP address that matched the attacking IP address.
View 1 Replies View RelatedBeen using the WRT160N for a while now and it works great except for one issue. Every few weeks the wireless can't be accessed by the other computers unless I change the SSID name. It was frustrating to figure out, but simply changing the name makes it accessible again.
View 1 Replies View RelatedRouter: E1200 2.0.02 build 3 Feb 15, 2012
These symptoms are stumping me:
WiFi drops 80% packets from new computers (Win7, IPv4 andIPv6 enabled) to reliable internet hosts. WiFi is OK (0% loss) from new computers to E1200 itself (ping E1200 IP address).Old computers, mobile devices, and wired are OK to reliable internet hosts.Basic Wireless Settings are Mixed, Auto Channel Width. Wireless Security is set to WPA2/WPA Mixed Mode. Guest Access enabled.
I'm having a bit of trouble with my e4200, It keeps on "dropping" connection, and by dropping I mean it constantly around 3-5 minutes the internet stops working with all my computers, it's connected by wifi with 2 PC's, and 1 PC is wired with an ethernet cable, and I also have 2 mobile devices connected at it. The internet would start working again within 30s, to 1m, but that it drops soon.Methods I've done to fix it:
-Updated firmware to the latest one
-Set the MTU to 1400
-Reset it, (30 second press)
-Rebooted, (Cooled down, doesn't really run hot just a little warm)
-Restored to factore defaults
I have a linksys wrvs4400n router on which:The wireless computers are connected to the home network (v lan 1)Port 1 is connected to the home network (v lan 1)Port 2 is connected to the office network (v lan 2)And the printers are connected to port 3.Now I'd like to setup the router in such a way that all computers have access to the printers (port 3), but I don't know what v lan settings I have to use on port 3, or if it is even possible...
View 5 Replies View Related